Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  One or more Power Seat Motors do not Operate  


DESCRIPTION

When a signal is input into the position control ECU and switch assembly, the ECU manages the signals received from the power seat switches, and operates each motors. If the position control ECU and switch assembly receives more than 2 motor operation signals, the motor is stopped. Manual operation is restarted after the position control ECU and switch assembly receives 1 signal only.

WIRING DIAGRAM

B352963E05
5.75,0.313 6.542,0.563 0.792,0.25 10 false SSRS 5.365,0.354 5.594,0.531 0.229,0.177 10 false Z10 5.365,0.781 5.625,0.958 0.26,0.177 10 false Z10 5.448,0.146 5.615,0.333 0.167,0.188 10 false 5 5.365,2.042 5.656,2.219 0.292,0.177 10 false Z10 5.448,1.865 5.615,2.052 0.167,0.188 10 false 4 5.75,0.76 6.177,0.938 0.427,0.177 10 false SGND 5.438,0.583 5.604,0.771 0.167,0.188 10 false 1 5.417,1.198 5.615,1.365 0.198,0.167 10 false Z9 5.75,1.188 6.125,1.354 0.375,0.167 10 false SLD+ 5.438,1 5.604,1.188 0.167,0.188 10 false 3 5.406,1.615 5.604,1.792 0.198,0.177 10 false Z9 5.75,1.594 6.115,1.771 0.365,0.177 10 false SLD- 5.438,1.417 5.604,1.604 0.167,0.188 10 false 4 3.125,0.271 3.26,0.438 0.135,0.167 10 false 5 3.125,0.698 3.26,0.854 0.135,0.156 10 false 6 3.135,1.125 3.25,1.302 0.115,0.177 10 false 4 3.125,1.51 3.229,1.677 0.104,0.167 10 false 3 5.417,2.875 5.604,3.052 0.188,0.177 10 false Z9 5.417,3.292 5.604,3.469 0.188,0.177 10 false Z9 5.75,2.865 6.104,3.063 0.354,0.198 10 false LFT+ 5.396,2.667 5.615,2.854 0.219,0.188 10 false 10 5.75,3.281 6.073,3.49 0.323,0.208 10 false LFT- 5.396,3.083 5.615,3.271 0.219,0.188 10 false 12 3.125,2.802 3.292,2.99 0.167,0.188 10 false 1 3.125,3.219 3.292,3.406 0.167,0.188 10 false 2 2.688,1.406 2.854,1.594 0.167,0.188 10 false M 2.688,3.083 2.823,3.271 0.135,0.188 10 false M 5.417,7.344 5.594,7.51 0.177,0.167 10 false Z9 5.385,6.5 5.677,6.677 0.292,0.177 10 false Z10 5.417,7.76 5.583,7.948 0.167,0.188 10 false Z9 5.75,7.344 6.167,7.51 0.417,0.167 10 false RCL+ 5.448,7.135 5.594,7.281 0.146,0.146 10 false 9 5.75,7.729 6.156,7.896 0.406,0.167 10 false RCL- 5.406,7.552 5.625,7.74 0.219,0.188 10 false 11 3.125,7.25 3.292,7.438 0.167,0.188 10 false 2 3.125,7.646 3.292,7.833 0.167,0.188 10 false 1 2.688,7.552 2.833,7.719 0.146,0.167 10 false M 0.271,0.615 0.552,0.802 0.281,0.188 10 false Z3 0.271,0.76 2.021,1.073 1.75,0.313 10 false Front Power Seat Position Motor LH (Slide Motor) 5.74,2.031 6.146,2.198 0.406,0.167 10 false SSRL 3.125,1.938 3.292,2.125 0.167,0.188 10 false 4 3.125,2.354 3.292,2.542 0.167,0.188 10 false 3 5.365,3.719 5.656,3.896 0.292,0.177 10 false Z10 3.135,3.708 3.427,3.885 0.292,0.177 10 false Z14 3.135,4.135 3.427,4.313 0.292,0.177 10 false Z14 3.177,4.542 3.365,4.719 0.188,0.177 10 false Z5 5.448,3.521 5.583,3.708 0.135,0.188 10 false 3 5.417,4.552 5.615,4.729 0.198,0.177 10 false Z9 5.417,4.969 5.615,5.135 0.198,0.167 10 false Z9 5.75,4.542 6.125,4.729 0.375,0.188 10 false FRV+ 5.448,4.333 5.667,4.521 0.219,0.188 10 false 8 5.75,4.969 6.156,5.135 0.406,0.167 10 false FRV- 5.448,4.76 5.573,4.948 0.125,0.188 10 false 5 3.229,4.344 3.344,4.521 0.115,0.177 10 false 2 3.219,4.76 3.385,4.948 0.167,0.188 10 false 1 2.688,4.76 2.823,4.948 0.135,0.188 10 false M 5.75,3.719 6.198,3.896 0.448,0.177 10 false SSFV 3.229,3.5 3.365,3.656 0.135,0.156 10 false 2 3.229,3.917 3.344,4.083 0.115,0.167 10 false 1 3.125,6.417 3.292,6.604 0.167,0.188 10 false 4 3.125,6.823 3.292,7.01 0.167,0.188 10 false 3 0.271,2.354 0.552,2.542 0.281,0.188 10 false Z4 0.271,2.51 1.927,2.823 1.656,0.313 10 false Front Power Seat Position Motor LH (Lifter Motor) 0.208,5.781 3.052,5.979 2.844,0.198 10 false Front Seat Cushion Frame Sub-assembly LH 5.76,6.531 6.219,6.719 0.458,0.188 10 false SSRR 5.406,6.281 5.646,6.469 0.24,0.188 10 false 11 0.271,6.823 0.552,7.01 0.281,0.188 10 false Z6 0.271,6.969 1.969,7.281 1.698,0.313 10 false Front Power Seat Position Motor LH (Reclining Motor) 0.219,8.156 2.865,8.354 2.646,0.198 10 false Front Seatback Frame Sub-assembly LH 0.271,4.125 1.969,4.438 1.698,0.313 10 false Front Power Seat Position Motor LH (Vertical Motor) 5.385,8.156 7,8.521 1.615,0.365 10 false Position Control ECU and Switch Assembly 3.188,4.979 3.385,5.156 0.198,0.177 10 false Z5

B352964E04
5.75,0.74 6.146,0.927 0.396,0.188 10 false +B1 5.417,0.74 5.594,0.917 0.177,0.177 10 false Z9 5.417,1.281 5.615,1.448 0.198,0.167 10 false Z9 5.448,0.521 5.615,0.708 0.167,0.188 10 false 7 5.75,1.292 6.198,1.49 0.448,0.198 10 false GND1 5.438,1.063 5.604,1.25 0.167,0.188 10 false 2 5.104,0.583 5.271,0.771 0.167,0.188 10 false 2 5.104,0.833 5.271,1.021 0.167,0.188 10 false 4 5.104,1.146 5.271,1.333 0.167,0.188 10 false 1 3.917,0.75 4.083,0.938 0.167,0.188 10 false 5 4.063,0.625 4.406,0.813 0.344,0.188 10 false Front 4.042,1.573 4.385,1.76 0.344,0.188 10 false Rear 3.917,1.25 4.083,1.438 0.167,0.188 10 false 3 3.135,0.802 3.302,0.99 0.167,0.188 10 false 2 3.115,1.292 3.281,1.479 0.167,0.188 10 false 1 2.688,1.135 2.823,1.313 0.135,0.177 10 false M 0.396,0.865 0.677,1.052 0.281,0.188 10 false Z8 0.292,3.448 0.573,3.635 0.281,0.188 10 false Z7 0.396,1.031 2.26,1.344 1.865,0.313 10 false Front Power Seat Cushion Control Motor LH (Leg Motor) 4.052,1.885 4.333,2.073 0.281,0.188 10 false Z15 4.052,2.073 5.188,2.563 1.135,0.49 10 false Front Power Seat Switch LH (Seat Cushion Control) 0.479,2.063 3.323,2.26 2.844,0.198 10 false Front Seat Cushion Frame Sub-assembly LH 5.75,3.344 6.063,3.5 0.313,0.156 10 false +B2 5.417,3.323 5.708,3.5 0.292,0.177 10 false Z9 5.417,3.76 5.594,3.938 0.177,0.177 10 false Z9 5.448,3.115 5.615,3.302 0.167,0.188 10 false 6 5.104,3.188 5.271,3.375 0.167,0.188 10 false 5 4.938,3.188 5.104,3.375 0.167,0.188 10 false B 4.063,3.323 4.229,3.51 0.167,0.188 10 false H 4.25,3.188 4.594,3.365 0.344,0.177 10 false Hold 4.177,4.271 4.74,4.458 0.563,0.188 10 false Release 4.063,3.823 4.229,4.01 0.167,0.188 10 false R 4.938,3.594 5.104,3.781 0.167,0.188 10 false E 5.104,3.594 5.271,3.781 0.167,0.188 10 false 2 3.906,3.344 4.073,3.531 0.167,0.188 10 false 3 3.906,3.844 4.073,4.031 0.167,0.188 10 false 1 5.76,3.771 6.24,3.958 0.479,0.188 10 false GND2 5.438,3.563 5.563,3.74 0.125,0.177 10 false 1 3.115,3.417 3.281,3.604 0.167,0.188 10 false 2 3.115,3.917 3.281,4.104 0.167,0.188 10 false 1 2.677,3.729 2.844,3.917 0.167,0.188 10 false M 0.292,3.635 2.313,3.948 2.021,0.313 10 false Front Lumbar Support Motor LH (Lumbar Motor) 4.031,4.656 4.313,4.844 0.281,0.188 10 false Z2 4.01,4.854 5.146,5.573 1.135,0.719 10 false Front Power Seat Switch LH (Lumbar Support Control) 0.615,4.656 3.094,4.865 2.479,0.208 10 false Lumbar Support Adjuster Assembly LH 5.448,4.302 7.063,4.667 1.615,0.365 10 false Position Control ECU and Switch Assembly

PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check which power seat functions are malfunctioning.

Result
Result Proceed to
One or more power seat functions do not operate A
All power seat functions do not operate B



A

2.CHECK FRONT POWER SEAT OPERATION

B

GO to OTHER FLOW CHART (Front Power Seat does not Operate with Front Power Seat Switch)

2.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the power seat switches (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

Result
Result Proceed to
Slide, front vertical and lifter functions do not operate A
Reclining functions do not operate B
Lumbar support adjustment function does not operate C
Leg support function does not operate D



A

3.READ VALUE USING TECHSTREAM (SLIDE, LIFTER, FRONT VERTICAL)

B

7.READ VALUE USING TECHSTREAM (RECLINING)

C

11.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (LUMBAR MOTOR)

D

15.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (LEG MOTOR)
3.READ VALUE USING TECHSTREAM (SLIDE, LIFTER, FRONT VERTICAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the Techstream.

Driver Seat
Tester Display Measurement item/Range Normal Condition Diagnostic Note
Front Vertical Down Front vertical switch signal (Downward) / ON or OFF ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
-
Front Vertical Up Front vertical switch signal (Upward) / ON or OFF ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
-
Lifter Switch Down Lifter switch signal (Downward) / ON or OFF ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off
-
Lifter Switch Up Lifter switch signal (Upward) / ON or OFF ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off
-
Slide Rear Sliding switch signal (Rearward) / ON or OFF ON: Sliding switch (Rearward) on
OFF: Sliding switch (Rearward) off
-
Slide Front Sliding switch signal (Forward) / ON or OFF ON: Sliding switch (Forward) on
OFF: Sliding switch (Forward) off
-

OK:

ON or OFF is displayed on the Techstream according to the table above.




OK

4.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE, LIFTER, VERTICAL MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

4.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE, LIFTER, VERTICAL MOTOR)
a.

Check the operation of the slide motor.

i.

Remove the front seat cushion frame sub-assembly LH (slide motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL).


ii.

Inspect the front seat cushion frame sub-assembly LH (slide motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION).



b.

Check the operation of the lifter motor.

i.

Remove the front seat cushion frame sub-assembly LH (lifter motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL).


ii.

Inspect the front seat cushion frame sub-assembly LH (lifter motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION).



c.

Check the operation of the vertical motor.

i.

Remove the front seat cushion frame sub-assembly LH (vertical motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL).


ii.

Inspect the front seat cushion frame sub-assembly LH (vertical motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION).




OK

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)

NG

REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z9 and Z10 position control ECU and switch assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-5 (SSRS) - Z3-5 Always Below 1 Ω
Z9-3 (SLD+) - Z3-4 Always Below 1 Ω
Z9-4 (SLD-) - Z3-3 Always Below 1 Ω
Z10-1 (SGND) - Z3-6 Always Below 1 Ω
Z10-3 (SSFV) - Z14-2 Always Below 1 Ω
Z9-8 (FRV+) - Z5-2 Always Below 1 Ω
Z9-5 (FRV-) - Z5-1 Always Below 1 Ω
Z10-1 (SGND) - Z14-1 Always Below 1 Ω
Z10-4 (SSRL) - Z4-4 Always Below 1 Ω
Z9-10 (LFT+) - Z4-1 Always Below 1 Ω
Z9-12 (LFT-) - Z4-2 Always Below 1 Ω
Z10-1 (SGND) - Z4-3 Always Below 1 Ω
Z10-5 (SSRS) or Z3-5 - Body ground Always 10 kΩ or higher
Z9-3 (SLD+) or Z3-4 - Body ground Always 10 kΩ or higher
Z9-4 (SLD-) or Z3-3 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z3-6 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z14-1 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z4-3 - Body ground Always 10 kΩ or higher
Z10-3 (SSFV) or Z14-2 - Body ground Always 10 kΩ or higher
Z9-8 (FRV+) or Z5-2 - Body ground Always 10 kΩ or higher
Z9-5 (FRV-) or Z5-1 - Body ground Always 10 kΩ or higher
Z10-4 (SSRL) or Z4-4 - Body ground Always 10 kΩ or higher
Z9-10 (LFT+) or Z4-1 - Body ground Always 10 kΩ or higher
Z9-12 (LFT-) or Z4-2 - Body ground Always 10 kΩ or higher




OK

6.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Temporarily replace the position control ECU and switch assembly with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).


b.

Check the front power seat control system (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

OK:

Power seat operates normally.




OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

7.READ VALUE USING TECHSTREAM (RECLINING)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the Techstream.

Driver Seat
Tester Display Measurement item/Range Normal Condition Diagnostic Note
Reclining Rear Reclining switch signal (Rearward) / ON or OFF ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
-
Reclining Front Reclining switch signal (Forward) / ON or OFF ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
-

OK:

ON or OFF is displayed on the Techstream according to the table above.




OK

8.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

8.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)
a.

Check the operation of the reclining motor.

i.

Remove the front seatback frame sub-assembly LH (reclining motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL).


ii.

Inspect the front seatback frame sub-assembly LH (reclining motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION).




OK

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)

NG

REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z9 and Z10 position control ECU and switch assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-11 (SSRR) - Z6-4 Always Below 1 Ω
Z9-9 (RCL+) - Z6-2 Always Below 1 Ω
Z9-11 (RCL-) - Z6-1 Always Below 1 Ω
Z10-1 (SGND) - Z6-3 Always Below 1 Ω
Z10-11 (SSRR) or Z6-4 - Body ground Always 10 kΩ or higher
Z9-9 (RCL+) or Z6-2 - Body ground Always 10 kΩ or higher
Z9-11 (RCL-) or Z6-1 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z6-3 - Body ground Always 10 kΩ or higher




OK

10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Temporarily replace the position control ECU and switch assembly with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).


b.

Check the front power seat control system (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

OK:

Power seat operates normally




OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH

11.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (LUMBAR MOTOR)
a.

Check the operation of the lumbar motor.

i.

Remove the lumbar support adjuster assembly LH (lumbar motor) (See page Vehicle Interior>SEAT>LUMBAR SUPPORT ADJUSTER ASSEMBLY>REMOVAL).


ii.

Inspect the lumbar support adjuster assembly LH (lumbar motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT LUMBAR SWITCH>INSPECTION).




OK

12.INSPECT FRONT POWER SEAT SWITCH LH (LUMBAR SUPPORT CONTROL)

NG

REPLACE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (LUMBAR MOTOR)

12.INSPECT FRONT POWER SEAT SWITCH LH (LUMBAR SUPPORT CONTROL)
a.

Check the operation of the lumbar support control.

i.

Remove the front power seat switch LH (lumbar support control) (See page Vehicle Interior>SEAT>FRONT POWER SEAT LUMBAR SWITCH>REMOVAL).


ii.

Inspect the front power seat switch LH (lumbar support control) (See page Vehicle Interior>SEAT>FRONT POWER SEAT LUMBAR SWITCH>INSPECTION).




OK

13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT POWER SEAT SWITCH LH)

NG

REPLACE FRONT POWER SEAT SWITCH LH

13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT POWER SEAT SWITCH LH)
a.

Disconnect the Z9 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z9-6 (+B2) - Z2-5 (B) Always Below 1 Ω
Z9-1 (GND2) - Z2-2 (E) Always Below 1 Ω
Z9-6 (+B2) or Z2-5 (B) - Body ground Always 10 kΩ or higher
Z9-1 (GND2) or Z2-2 (E) - Body ground Always 10 kΩ or higher




OK

14.CHECK HARNESS AND CONNECTOR (LUMBAR SUPPORT ADJUSTER ASSEMBLY LH - FRONT POWER SEAT SWITCH LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (LUMBAR SUPPORT ADJUSTER ASSEMBLY LH - FRONT POWER SEAT SWITCH LH)
a.

Disconnect the Z7 lumbar support adjuster assembly LH (lumbar motor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z2-1 (R) - Z7-1 Always Below 1 Ω
Z2-3 (H) - Z7-2 Always Below 1 Ω
Z2-1 (R) or Z7-1 - Body ground Always 10 kΩ or higher
Z2-3 (H) or Z7-2 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (LEG MOTOR)
a.

Check the operation of the leg motor.

i.

Remove the front seat cushion frame sub-assembly LH (leg motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL).


ii.

Inspect the front seat cushion frame sub-assembly LH (leg motor) )(See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION).




OK

16.INSPECT FRONT POWER SEAT SWITCH LH (SEAT CUSHION CONTROL)

NG

REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

16.INSPECT FRONT POWER SEAT SWITCH LH (SEAT CUSHION CONTROL)
a.

Check the operation of the seat cushion control.

i.

Remove the front power seat switch LH (seat cushion control) (See page Vehicle Interior>SEAT>SEAT VARIABLE CUSHION SWITCH>REMOVAL).


ii.

Inspect the front power seat switch LH (seat cushion control) (See page Vehicle Interior>SEAT>SEAT VARIABLE CUSHION SWITCH>INSPECTION).




OK

17.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT POWER SEAT SWITCH LH)

NG

REPLACE FRONT POWER SEAT SWITCH LH

17.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT POWER SEAT SWITCH LH)
a.

Disconnect the Z9 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z9-7 (+B1) - Z15-2 Always Below 1 Ω
Z9-2 (GND1) - Z15-1 Always Below 1 Ω
Z9-2 (GND1) - Z15-4 Always Below 1 Ω
Z9-7 (+B1) or Z15-2 - Body ground Always 10 kΩ or higher
Z9-2 (GND1) or Z15-1 - Body ground Always Below 1 Ω
Z9-2 (GND1) or Z15-4 - Body ground Always Below 1 Ω




OK

18.CHECK HARNESS AND CONNECTOR (FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH - FRONT POWER SEAT SWITCH LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH - FRONT POWER SEAT SWITCH LH)
a.

Disconnect the Z8 front seat cushion frame sub-assembly LH (leg motor) connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
Z15-5 - Z8-2 Always Below 1 Ω
Z15-3 - Z8-1 Always Below 1 Ω
Z15-5 or Z8-2 - Body ground Always 10 kΩ or higher
Z15-3 or Z8-1 - Body ground Always 10 kΩ or higher



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR