Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2650  Slide Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite forward or rearward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2650 The forward and rearward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Front seat cushion frame sub-assembly LH (slide motor)

·

Harness or connector



WIRING DIAGRAM

B352948E02
1.024,2.333 1.418,2.474 0.394,0.141 10 Z3 1.024,2.476 2.729,2.835 1.705,0.360 10 Front Power Seat Position Motor LH (Slide Motor) 0.471,3.254 3.308,3.441 2.837,0.187 10 Front Seat Cushion Frame Sub-assembly LH 2.227,1.969 2.621,2.144 0.394,0.175 10 6 2.227,0.957 2.621,1.134 0.394,0.177 10 3 2.227,0.453 2.621,0.629 0.394,0.175 10 4 2.227,1.465 2.621,1.639 0.394,0.173 10 5 5.161,2.06 5.584,2.201 0.423,0.141 10 SGND 4.826,2.537 6.470,2.952 1.644,0.415 10 Position Control ECU and Switch Assembly 5.161,1.047 5.556,1.188 0.394,0.141 10 SLD- 5.161,0.544 5.556,0.685 0.394,0.141 10 SLD+ 5.161,1.556 5.580,1.697 0.419,0.141 10 SSRS 4.774,2.06 5.060,2.201 0.286,0.141 10 Z10 4.814,1.047 5.070,1.188 0.256,0.141 10 Z9 4.814,0.544 5.070,0.685 0.256,0.141 10 Z9 4.774,1.556 5.046,1.697 0.272,0.141 10 Z10 4.852,1.852 4.958,1.993 0.106,0.141 10 1 4.852,0.84 4.958,0.981 0.106,0.141 10 4 4.852,0.336 4.958,0.477 0.106,0.141 10 3 4.852,1.348 4.958,1.490 0.106,0.141 10 5

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (SEAT SLIDE OPERATION)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Seat Slide Operation Seat sliding operation Front / OFF / Rear -

OK:

Motor operates normally.




OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)

NG

5.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE MOTOR)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)
a.
U152016E02
0.76,1.052 0.969,1.229 0.208,0.177 10 false Z3 0.115,0.115 0.323,0.292 0.208,0.177 10 false *a

Disconnect the front seat cushion frame sub-assembly LH (slide motor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z3-5 - Z3-6 Sliding switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Front Seat Cushion Frame Sub-assembly LH [Slide Motor])



OK

3.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
3.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE MOTOR)
a.
U152017E02
0.094,0.104 0.385,0.333 0.292,0.229 10 false *a 0.75,1 0.948,1.188 0.198,0.188 10 false Z3

Reconnect the front seat cushion frame sub-assembly LH (slide motor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z3-5 - Body ground Sliding switch on 4.5 to 4.8 V


Text in Illustration
*a Component with harness connected
(Front Seat Cushion Frame Sub-assembly LH [Slide Motor])



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z10 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-5 (SSRS) - Z3-5 Always Below 1 Ω
Z10-1 (SGND) - Z3-6 Always Below 1 Ω
Z10-5 (SSRS) or Z3-5 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z3-6 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE MOTOR)
a.

Remove the front seat cushion frame sub-assembly LH (slide Motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL).


b.

Inspect the front seat cushion frame sub-assembly LH (slide motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)

NG

REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z9 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z9-3 (SLD+) - Z3-4 Always Below 1 Ω
Z9-4 (SLD-) - Z3-3 Always Below 1 Ω
Z9-3 (SLD+) or Z3-4 - Body ground Always 10 kΩ or higher
Z9-4 (SLD-) or Z3-3 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR