Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2652  Front Vertical Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2652 The upward and downward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Front seat cushion frame sub-assembly LH (vertical motor)

·

Harness or connector



WIRING DIAGRAM

B352949E01
2.3,1.051 2.694,1.192 0.394,0.141 10 Z5 2.264,1.558 2.659,1.699 0.394,0.141 10 Z14 2.264,2.066 2.659,2.207 0.394,0.141 10 Z14 2.3,0.543 2.694,0.684 0.394,0.141 10 Z5 0.968,2.388 2.772,2.748 1.804,0.360 10 Front Power Seat Position Motor LH (Vertical Motor) 0.57,3.254 3.407,3.441 2.837,0.187 10 Front Seat Cushion Frame Sub-assembly LH 2.344,1.852 2.739,1.993 0.394,0.141 10 1 2.344,0.84 2.739,0.981 0.394,0.141 10 1 2.344,0.336 2.739,0.477 0.394,0.141 10 2 2.344,1.348 2.739,1.490 0.394,0.141 10 2 5.161,2.06 5.584,2.201 0.423,0.141 10 SGND 4.826,2.537 6.470,2.952 1.644,0.415 10 Position Control ECU and Switch Assembly 5.161,1.047 5.556,1.188 0.394,0.141 10 FRV- 5.161,0.544 5.556,0.685 0.394,0.141 10 FRV+ 5.161,1.556 5.580,1.697 0.419,0.141 10 SSFV 4.774,2.06 5.060,2.201 0.286,0.141 10 Z10 4.814,1.047 5.070,1.188 0.256,0.141 10 Z9 4.814,0.544 5.070,0.685 0.256,0.141 10 Z9 4.774,1.556 5.046,1.697 0.272,0.141 10 Z10 4.852,1.852 4.958,1.993 0.106,0.141 10 1 4.852,0.84 4.958,0.981 0.106,0.141 10 5 4.852,0.336 4.958,0.477 0.106,0.141 10 8 4.852,1.348 4.958,1.490 0.106,0.141 10 3

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (FRONT VERTICAL OPERATION)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Front Vertical Operation Seat front vertical operation Up / OFF / Down -

OK:

Motor operates normally.




OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (VERTICAL MOTOR CIRCUIT)

NG

5.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (VERTICAL MOTOR)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (VERTICAL MOTOR CIRCUIT)
a.
U152035E02
0.688,0.865 0.979,1.042 0.292,0.177 10 false Z14 0.125,0.125 0.333,0.302 0.208,0.177 10 false *a

Disconnect the front seat cushion frame sub-assembly LH (vertical motor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z14-1 - Z14-2 Front vertical switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Front Seat Cushion Frame Sub-assembly LH [Vertical Motor])



OK

3.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (VERTICAL MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
3.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (VERTICAL MOTOR)
a.
U152036E02
0.115,0.083 0.323,0.313 0.208,0.229 10 false *a 0.688,0.948 0.979,1.146 0.292,0.198 10 false Z14

Reconnect the front seat cushion frame sub-assembly LH (vertical motor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z14-2 - Body ground Front vertical switch on 4.5 to 4.8 V


Text in Illustration
*a Component with harness connected
(Front Seat Cushion Frame Sub-assembly LH [Vertical Motor])



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z10 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-3 (SSFV) - Z14-2 Always Below 1 Ω
Z10-1 (SGND) - Z14-1 Always Below 1 Ω
Z10-3 (SSFV) or Z14-2 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z14-1 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (VERTICAL MOTOR)
a.

Remove the front seat cushion frame sub-assembly LH (vertical motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL).


b.

Inspect the front seat cushion frame sub-assembly LH (vertical motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)

NG

REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z9 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z9-8 (FRV+) - Z5-2 Always Below 1 Ω
Z9-5 (FRV-) - Z5-1 Always Below 1 Ω
Z9-8 (FRV+) or Z5-2 - Body ground Always 10 kΩ or higher
Z9-5 (FRV-) or Z5-1 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR