Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2653  Lifter Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2653 The upward and downward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Front seat cushion frame sub-assembly RH (lifter motor)

·

Harness or connector



WIRING DIAGRAM

B352948E05
1.004,2.333 1.398,2.474 0.394,0.141 10 Z4 1.004,2.476 2.665,2.835 1.661,0.360 10 Front Power Seat Position Motor LH (Lifter Motor) 0.527,3.254 3.364,3.441 2.837,0.187 10 Front Seat Cushion Frame Sub-assembly LH 2.227,1.969 2.621,2.110 0.394,0.141 10 3 2.227,0.957 2.621,1.098 0.394,0.141 10 2 2.227,0.453 2.621,0.594 0.394,0.141 10 1 2.227,1.465 2.621,1.607 0.394,0.141 10 4 5.161,2.06 5.584,2.201 0.423,0.141 10 SGND 4.826,2.537 6.470,2.952 1.644,0.415 10 Position Control ECU and Switch Assembly 5.161,1.047 5.556,1.188 0.394,0.141 10 LFT- 5.161,0.544 5.556,0.685 0.394,0.141 10 LFT+ 5.161,1.556 5.580,1.697 0.419,0.141 10 SSRL 4.774,2.06 5.060,2.201 0.286,0.141 10 Z10 4.814,1.047 5.070,1.188 0.256,0.141 10 Z9 4.814,0.544 5.070,0.685 0.256,0.141 10 Z9 4.774,1.556 5.046,1.697 0.272,0.141 10 Z10 4.852,1.852 4.958,1.993 0.106,0.141 10 1 4.82,0.84 5.004,0.981 0.184,0.141 10 12 4.82,0.336 5.050,0.477 0.230,0.141 10 10 4.852,1.348 5.036,1.490 0.184,0.141 10 4

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (LIFTER OPERATION)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Lifter Operation Seat lifter operation Up / OFF / Down -

OK:

Motor operates normally.




OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)

NG

5.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (LIFTER MOTOR)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)
a.
U152031E02
0.052,0 0.26,0.208 0.208,0.208 10 false *a 0.375,0.958 0.573,1.156 0.198,0.198 10 false Z4

Disconnect the front seat cushion frame sub-assembly LH (lifter motor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z4-3 - Z4-4 Lifter switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Front Seat Cushion Frame Sub-assembly [Lifter Motor])



OK

3.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (LIFTER MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
3.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (LIFTER MOTOR)
a.
U152034E02
0.094,0.073 0.302,0.292 0.208,0.219 10 false *a 0.302,0.99 0.531,1.177 0.229,0.188 10 false Z4

Reconnect the front seat cushion frame sub-assembly LH (lifter motor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z4-4 - Body ground Lifter switch on 4.5 to 4.8 V


Text in Illustration
*a Component with harness connected
(Front Seat Cushion Frame Sub-assembly LH [Lifter Motor])



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z10 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-4 (SSRL) - Z4-4 Always Below 1 Ω
Z10-1 (SGND) - Z4-3 Always Below 1 Ω
Z10-4 (SSRL) or Z4-4 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z4-3 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (LIFTER MOTOR)
a.

Remove the front seat cushion frame sub-assembly LH (lifter motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL).


b.

Inspect the front seat cushion frame sub-assembly LH (lifter motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)

NG

REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z9 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z9-10 (LFT+) - Z4-1 Always Below 1 Ω
Z9-12 (LFT-) - Z4-2 Always Below 1 Ω
Z9-10 (LFT+) or Z4-1 - Body ground Always 10 kΩ or higher
Z9-12 (LFT-) or Z4-2 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR