Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM27M0U _58 Vehicle Interior _049137 DOOR LOCK _0234323 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. This DTC is output when the applicable RDA signal cannot be received within 1 second of the PRG signal being output from the main body ECU.

DTC No. DTC Detection Condition Trouble Area
B1242 In diagnostic mode, applicable RDA signal cannot be received within 1 second of PRG signal being output from main body ECU
·

Harness or connector

·

Door control receiver

·

Main body ECU



WIRING DIAGRAM

U152757E02
0.938,1.135 1.344,1.333 0.406,0.198 10 false PRG 0.948,1.969 1.344,2.167 0.396,0.198 10 false RDA 5.969,1.115 6.375,1.313 0.406,0.198 10 false PRG 5.979,1.948 6.375,2.146 0.396,0.198 10 false RDA 1.063,2.823 1.302,3.052 0.24,0.229 10 false +B 0.948,3.667 1.375,3.823 0.427,0.156 10 false GND 4.26,3.833 5.208,4.031 0.948,0.198 10 false from Battery 0.208,5.146 1.677,5.344 1.469,0.198 10 false Door Control Receiver 5.76,5.188 6.792,5.406 1.031,0.219 10 false Main Body ECU 5.677,1 5.979,1.313 0.302,0.313 10 false 10 5.667,1.854 5.969,2.167 0.302,0.313 10 false 12 1.375,3.531 1.677,3.844 0.302,0.313 10 false 1 1.375,2.698 1.677,3.01 0.302,0.313 10 false 5 1.375,1.844 1.677,2.156 0.302,0.313 10 false 2 1.375,1.01 1.677,1.323 0.302,0.313 10 false 3 2.844,2.958 3.552,3.125 0.708,0.167 10 false ECU-B1 0.198,4.99 0.594,5.188 0.396,0.198 10 false Q7 5.771,5.021 6.167,5.219 0.396,0.198 10 false J3

PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTC (see page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1242 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
B443029E01
0.24,1.396 0.635,1.625 0.396,0.229 0.354,3.625 0.75,3.854 0.396,0.229 2.385,1.281 2.688,1.198 true 0.719,1.813 1.177,1.594 true 1.25,4.417 1.479,3.99 true 1.896,4.417 1.708,4 true 0.188,0.167 2.448,0.542 2.26,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.208,2.5 2.469,2.875 2.26,0.375 10 false Front view of wire harness connector: (to Door Control Receiver) 0.365,1.427 0.573,1.604 0.208,0.177 10 false J3 0.458,3.656 0.667,3.833 0.208,0.177 10 false Q7 2.75,1.115 3.208,1.313 0.458,0.198 10 false PRG 0.5,1.844 0.844,2.042 0.344,0.198 10 false RDA 0.917,4.354 1.375,4.552 0.458,0.198 10 false RDA 1.948,4.375 2.406,4.573 0.458,0.198 10 false PRG

a.

Disconnect the J3 ECU connector.


b.

Disconnect the Q7 receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J3-12 (RDA) - Q7-2 (RDA) Always Below 1 Ω
J3-10 (PRG) - Q7-3 (PRG)
J3-12 (RDA) or Q7-2 (RDA) - Body ground Always 10 kΩ or higher
J3-10 (PRG) or Q7-3 (PRG) - Body ground




OK

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
U151864E02
1.208,2.146 0.99,2.448 true 2.208,2.135 2.469,2.438 true 0.104,0.167 2.375,0.615 2.271,0.448 10 false Front view of wire harness connector: (to Door Control Receiver) 2.521,2.385 2.844,2.583 0.323,0.198 10 false +B 0.646,2.385 1.01,2.583 0.365,0.198 10 false GND 0.385,1.792 0.677,2.083 0.292,0.292 10 false Q7

a.

Disconnect the Q7 receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q7-1 (GND) - Body ground Always Below 1 Ω


Standard voltage:
Tester Connection Condition Specified Condition
Q7-5 (+B) - Body ground Always 11 to 14 V




OK

5.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new one.

i.

For Regular Cab, refer to the following procedures (see page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(for Regular Cab)>COMPONENTS).


ii.

For Double Cab, refer to the following procedures (see page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(for Double Cab)>COMPONENTS).


iii.

For CrewMax, refer to the following procedures (see page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(for CrewMax)>REMOVAL).



b.

Perform the REGISTRATION procedures (see page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>REGISTRATION).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTC (see page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1242 is not output.




OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)