Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM27M0U _58 Vehicle Interior _049137 DOOR LOCK _0234323 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning lights and/or wireless door lock buzzer answer-back function(s) do not operate. In such cases, the main body ECU's hazard warning lights and wireless door lock buzzer signal outputs may be malfunctioning.

NOTICE:

Troubleshooting should be started after confirming that the customize status of the answer-back function has been switched ON.


WIRING DIAGRAM

B443030E01
2.917,2.219 4.688,2.427 1.771,0.208 10 false Wireless Door Lock Buzzer 2.927,2.063 3.219,2.25 0.292,0.188 10 false A34 3.323,1.833 3.479,2.01 0.156,0.177 10 false E 3.604,1.833 3.76,2.01 0.156,0.177 10 false B 3.125,1.719 3.281,1.896 0.156,0.177 10 false 2 3.802,1.719 3.958,1.896 0.156,0.177 10 false 1 5.688,1.625 5.823,1.813 0.135,0.188 10 false 7 5.635,1.833 5.792,2.01 0.156,0.177 10 false J1 5.906,1.833 6.24,2.031 0.333,0.198 10 false BZR 5.906,3.906 6.24,4.104 0.333,0.198 10 false HAZ 5.635,3.917 5.792,4.094 0.156,0.177 10 false J2 5.656,3.708 5.792,3.896 0.135,0.188 10 false 4 5.042,2.948 5.375,3.146 0.333,0.198 10 false HAZ 4.76,2.844 4.969,3.031 0.208,0.188 10 false 12 4.438,3.198 4.708,3.396 0.271,0.198 10 false J29 4.438,3.375 4.958,3.729 0.521,0.354 10 false Flasher Relay 1.938,3.281 2.271,3.469 0.333,0.188 10 false J127 1.927,3.448 3.854,3.656 1.927,0.208 10 false Hazard Warning Signal Switch 2.146,3.063 2.479,3.25 0.333,0.188 10 false GND 2.625,3.063 2.958,3.25 0.333,0.188 10 false HAZ 1.99,2.854 2.177,3.021 0.188,0.167 10 false 5 2.948,2.854 3.135,3.021 0.188,0.167 10 false 1 5.792,4.344 6.854,4.542 1.063,0.198 10 false Main Body ECU

PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTION
a.

Check the wireless door lock control functions by operating the transmitter switch.

Result
Result Proceed to
Wireless door lock functions are normal but hazard warning light answer-back does not occur A
Wireless door lock functions are normal but wireless door lock buzzer answer-back does not occur B
Doors cannot be locked and unlocked with transmitter C



A

2.PERFORM ACTIVE TEST USING TECHSTREAM (TURN SIGNAL FLASHER RELAY)

B

3.PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS DOOR LOCK BUZZER)

C

2.PERFORM ACTIVE TEST USING TECHSTREAM (TURN SIGNAL FLASHER RELAY)
a.

Select the Active Test, use the Techstream to generate a control command, and then check that the hazard warning lights flash.

Main body
Tester Display Test Part Control Range Diagnostic Note
Hazard Flasher relay ON/OFF -


OK:

Hazard warning lights turn ON or OFF.



OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

NG

3.PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS DOOR LOCK BUZZER)
a.

Select the Active Test, use the Techstream to generate a control command, and then check that the wireless buzzer operates normally.

Main body
Tester Display Test Part Control Range Diagnostic Note
Wireless Buzzer Sounds wireless buzzer ON/OFF -


OK:

Wireless buzzer turns ON or OFF.



OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

NG

4.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU AND BODY GROUND)
U152755E01
0.178,2.081 2.594,2.495 2.416,0.414 10 Front view of wire harness connector: (to Main Body ECU) 0.178,0.132 2.594,0.546 2.416,0.414 10 Front view of wire harness connector: (to Wireless Door Lock Buzzer) 0.448,1.04 0.816,1.212 0.368,0.172 10 A34 0.484,2.852 0.697,3.024 0.213,0.172 10 J1 0.353,3.702 0.680,3.884 0.327,0.182 10 BZR 0.886,1.727 1.015,1.909 0.129,0.182 10 B 2.443,1.727 2.572,1.909 0.129,0.182 10 E 0.745,3.766 0.938,3.766 0.938,3.766 1.414,3.941 false 1.043,1.811 1.192,1.811 1.192,1.811 1.461,1.633 false 2.434,1.811 2.285,1.811 2.285,1.811 2.016,1.633 false

a.

Disconnect the A34 buzzer connector.


b.

Disconnect the J1 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A34-1 (B) - J1-7 (BZR) Always Below 1 Ω
A34-2 (E) - Body ground
A34-1 (B) or J1-7 (BZR) - Body ground Always 10 kΩ or higher




OK

5.CHECK WIRELESS DOOR LOCK BUZZER (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRELESS DOOR LOCK BUZZER (OPERATION)
a.

Temporarily replace the wireless door lock buzzer with a new or normally functioning one (see page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>COMPONENTS).


b.

Check that the buzzer sounds when using the transmitter LOCK and UNLOCK switches.

OK:

The buzzer sounds.


NOTICE:

When battery voltage is directly applied to the buzzer, the buzzer does not sound.


HINT:

The buzzer circuit is built into the main body ECU, not into the buzzer itself.




OK

END (WIRELESS DOOR LOCK BUZZER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)