Home › Vehicle Interior › ENGINE HOOD / DOOR › FRONT DOOR(for CrewMax)
RM27M0U _58 Vehicle Interior _049138 ENGINE HOOD / DOOR _0234340 FRONT DOOR(for CrewMax) A

ENGINE HOOD / DOOR  FRONT DOOR(for CrewMax)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 67862 1.INSTALL FRONT DOOR WEATHERSTRIP LH

a.
B166219

Attach the 38 clips to install the weatherstrip.

HINT:

If clips are damaged during installation, replace them.



Hide 68620 2.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.
B165675

Apply MP grease to the sliding areas of the door check.


b.

Install the door check to the door panel with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 67856B 3.INSTALL FRONT DOOR PANEL PROTECTOR LH

a.
B166214

Attach the 8 clips to install the door panel protector.


Hide 67924 4.INSTALL FRONT NO. 2 DOOR STIFFENER CUSHION

a.
B165680

Install the stiffener cushion with the 2 clips.


Hide 69332 5.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.

Install the lock open rod to the outside handle frame.


Hide 69202A 6.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B165673

Slide the outside handle frame to install it.

NOTICE:

If the release plate is not pulled and held when installing the outside handle, it will strike against the outside handle and become damaged.



b.

Using a T30 "TORX" wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Install the front and rear outside handle pads.


Hide 69220 7.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B165681

Install the handle by pushing it in the direction of the arrow in the illustration.

NOTICE:

If the bellcrank lever is not pulled and held when installing the handle, the bellcrank lever will interfere with the handle and become damaged.



Hide 69760C 8.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B165672E03
2.125,0.958 2,0.167 2,0.167 1.781,0.167 false 0.406,0.083 1.771,0.521 1.365,0.438 10 true End Cap (Color: Blue)

Install the front door inside locking cable.


b.
B266907

Attach the 3 claws.


Hide 69720B 9.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B165670E06
2.125,1.125 2.125,1.594 false 1.375,1.625 2.854,2 1.479,0.375 10 true End Cap (Color: Yellow)

Install the front door lock remote control cable.


Hide 69320 10.INSTALL FRONT DOOR LOCK ASSEMBLY LH

a.

Apply MP grease to the sliding and rotating areas of the door lock.


b.

Install a new door lock wire harness packing to the door lock.

NOTICE:
·

When reusing a door lock that has been removed, replace the packing in the connecting part with new packing.

·

Be careful that no grease or dirt sticks to the packing surface in the connecting part.

·

Reusing removed packing or using damaged packing will allow water to penetrate through to the connecting part, resulting in a malfunction of the door lock.




c.
B165669

Using a T30 ''TORX'' wrench, install the door lock with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the door lock connector.


Hide 69217F 11.INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH

a.
B165665E01
0.607,1.626 1.345,1.928 0.738,0.303 10 Hole Plug 2.889,1.739 1.377,1.739 false

Using a T30 ''TORX'' socket, install the cover (with the door key cylinder) with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Install the hole plug.


Hide 67402F 12.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH

a.
B165663

Install the frame with the 2 bolts.


Hide 67404F 13.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B165682

Install the frame with the 2 bolts.


Hide 68151E 14.INSTALL FRONT DOOR GLASS RUN LH

a.
B165689

Install the front door glass run.


Hide 68210C 15.INSTALL FRONT OUTER DOOR GLASS WEATHERSTRIP ASSEMBLY LH

Hide 89860A 16.INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH

a.
B166953

Install the side airbag sensor with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.

Connect the connector.


Hide 85720A 17.INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B165662

Apply MP grease to the sliding and rotating areas of the regulator motor.


b.

Using a T25 ''TORX'' driver, install the motor with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

For a new front window regulator, the installation position of the regulator will be set when the self-tapping screws are installed.



Hide 69802 18.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B166218E03
1.604,1.188 1.813,1.333 0.208,0.146 1.469,1.052 1.74,1.063 1.74,1.063 2.365,1.406 false 0.479,0.979 1.458,1.354 0.979,0.375 10 true Temporary Bolt

Apply MP grease to the sliding and rotating areas of the window regulator.

NOTICE:

Do not apply grease to the spring of the window regulator.



b.

Loosely install the temporary bolt onto the window regulator.


c.

Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.


d.

Temporarily install the window regulator with the 5 bolts, and tighten the temporary bolt so that it contacts the door panel.


e.

Tighten the 6 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.

Connect the connector.


Hide 68102 19.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.
B442527

Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

NOTICE:

Be careful not to damage the glass.



b.
B166216

Install the door glass to the window regulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67832 20.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.

Install the front door service hole cover to the door panel.

NOTICE:
·

When installing the service hole cover, pull out the links through the service hole cover.

·

There should be no wrinkles or folds after attaching the service hole cover.

·

After attaching the service hole cover, check the sealing quality.




b.

Connect the connector.


Hide 67625A 21.INSTALL FRONT NO. 1 DOOR TRIM BRACKET

a.
B165656

Install the bracket with the 2 screws.


Hide 87940 23.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 89430 24.INSTALL OUTER MIRROR CONTROL ECU

a.
B166706

Install the ECU with the 2 screws.


b.

Connect the 2 ECU connectors.


Hide 84927 25.INSTALL SEAT MEMORY SWITCH (w/ Seat Memory Switch)

a.
B166227

Install the seat memory with the 2 screws.


Hide 68172A 26.INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH

Hide 67602 27.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B165684E04
2.531,1.51 2.698,1.958 2.698,1.958 2.458,1.958 false 2.167,0.875 2.792,0.167 2.792,0.167 2.417,0.167 false 0.927,0.063 2.385,0.458 1.458,0.396 10 true End Cap (Color: White) 1.021,1.854 2.49,2.156 1.469,0.302 10 true End Cap (Color: Green)

Connect the 2 cables to the inside handle.


b.

Connect the connector.


c.

Attach the inside handle's knob to the door trim board.


d.
B354849E01
2.355,0.263 2.691,0.456 0.336,0.193 10 Clip 3.26,1.547 2.784,0.361 2.784,0.361 2.704,0.361 false

Attach the 9 clips to install the door trim board.


e.

Install the inside handle and door trim board to the door trim panel with the screw.


f.

Install the door trim board to the door panel with the screw.


g.

Install the clip.


Hide 74222A 28.INSTALL FRONT DOOR ARMREST COVER LH

Hide 67492A 30.INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH

a.
B168274E04
0.063,0 1.188,0.333 1.125,0.333 12 false for Standard: 0.042,2.344 1.74,2.677 1.698,0.333 12 false for 12 Speakers:

Attach the 3 clips to install the front lower door frame bracket garnish.


Hide 84820 31.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

Hide 74232 32.INSTALL FRONT UPPER ARMREST BASE PANEL LH

a.

Connect the master switch connector.


b.
B360330

Attach the 2 clips and 5 claws to install the front upper armrest base panel LH.


Hide 69284C 33.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

a.
U151897E01
1.213,1.893 1.231,1.875 1.231,1.875 1.245,1.875 false

Attach the 4 claws to install the bezel plug.


Hide 34.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
w/ Jam Protection Function:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION).


Hide 35. CHECK SRS WARNING LIGHT