Home › Vehicle Interior › ENGINE HOOD / DOOR › REAR DOOR(for CrewMax)
RM27M0U _58 Vehicle Interior _049138 ENGINE HOOD / DOOR _0234341 REAR DOOR(for CrewMax) A

ENGINE HOOD / DOOR  REAR DOOR(for CrewMax)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 67872 1.INSTALL REAR DOOR WEATHERSTRIP LH

a.
B169270

Attach the 41 clips to install the weatherstrip.

HINT:

If clips are damaged during installation, replace them.



b.
B170112

Attach the 2 clips.


Hide 68640A 2.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.
B166256

Apply MP grease to the sliding areas of the door check.


b.

Install the door check to the door panel with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 67888A 3.INSTALL REAR NO. 2 DOOR WEATHERSTRIP LH

a.
B169269

Attach the 10 clips to install the weatherstrip.


Hide 69332 4.INSTALL REAR DOOR LOCK OPEN ROD LH

Hide 69204A 5.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B169266

Slide the outside handle frame to install it.

NOTICE:

If the release plate is not pulled and held when installing the outside handle, it will strike against the outside handle and become damaged.



b.

Using a T30 "TORX" wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Install the front and rear outside handle pads.


Hide 69240 6.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
U151970

Install the handle by pushing it in the direction of the arrow in the illustration.

NOTICE:

If the bellcrank lever is not pulled and held when installing the handle, the bellcrank lever will interfere with the handle and become damaged.



Hide 69227L 7.INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

a.
B170110

Using a T30 ''TORX'' socket, install the cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Install the hole plug.


Hide 67836H 8.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

Hide 69780B 9.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B167682E02
1.927,0.552 2.073,0.552 2.073,0.552 2.219,1.135 false 0.406,0.49 1.906,0.854 1.5,0.365 10 true End Cap (Color: Yellow)

Install the rear door inside locking cable.


b.
B266908

Attach the 3 claws.


Hide 69740D 10.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B169264E02
2.031,1.031 2.031,1.5 false 1.396,1.51 2.771,1.854 1.375,0.344 10 true End Cap (Color: Blue)

Install the rear door lock remote control cable.


b.
B266912

Attach the claw.


Hide 69060A 11.INSTALL REAR DOOR LOCK ASSEMBLY LH

a.

Apply MP grease to the sliding and rotating parts of the rear door lock.


b.

Install a new door lock wire harness packing to the door lock.

NOTICE:
·

When reusing a door lock that has been removed, replace the packing in the connecting part with new packing.

·

Be careful that no grease or dirt sticks to the packing surface in the connecting part.

·

Reusing removed packing or using damaged packing will allow water to penetrate through to the connecting part, resulting in a malfunction of the door lock.




c.
B169263

Using a T30 ''TORX'' wrench, install the door lock with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the connector.


Hide 85720D 12.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.

Apply MP grease to the sliding and rotating areas of the regulator motor.


b.
B166252

Using a T25 ''TORX'' driver, install the motor with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

For a new rear window regulator, the installation position of the regulator will be set when the self-tapping screws are installed.



Hide 69804 13.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the rear door power window regulator.


b.
U151969E02
2.781,1.208 1.583,0.479 1.583,0.479 1.292,0.479 false 0.25,0.396 1.26,0.74 1.01,0.344 10 true Temporary Bolt 2.688,1.51 2.833,1.708 0.146,0.198 10 true 1 3.188,1.083 3.323,1.292 0.135,0.208 10 true 2 3.042,1.5 3.188,1.698 0.146,0.198 10 true 3 2.844,1.167 2.99,1.365 0.146,0.198 10 true 4 2.073,1.813 2.219,2.01 0.146,0.198 10 false 5 2.302,1.802 2.448,2 0.146,0.198 10 false 6

Loosely install the temporary bolt onto the window regulator.


c.

Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.


d.

Temporarily install the window regulator with the 5 bolts, and tighten the temporary bolt so that it contacts the door panel.


e.

Tighten the 6 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68163 14.INSTALL REAR OUTER DOOR GLASS WEATHERSTRIP

Hide 68192B 15.INSTALL REAR NO. 2 DOOR GLASS RUN LH

a.

Install the rear door glass run to the rear door window front lower guide.


Hide 67406B 16.INSTALL REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH

a.
B169261

Install the rear door front window guide to the door panel with the 2 bolts.


Hide 68104 17.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

a.
B171301

Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

NOTICE:

Be careful not to damage the glass.



b.

Install the door glass to the window regulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67408F 18.INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

a.
B169259

Install the rear door rear lower window frame to the door panel with the 2 bolts.


Hide 68152C 19.INSTALL REAR DOOR GLASS RUN LH

a.
B169257

Install the rear door glass run.


Hide 67842E 20.INSTALL REAR DOOR SERVICE HOLE COVER LH

a.
B169256

Attach the 5 clamps to install the rear door service hole cover.

NOTICE:
·

When installing the service hole cover, pull out the links through the service hole cover.

·

There should be no wrinkles or folds after attaching the service hole cover.

·

After attaching the service hole cover, check the sealing quality.




Hide 67626C 22.INSTALL REAR NO. 2 DOOR TRIM BRACKET

a.
B266909

Install the bracket with the 2 screws.


Hide 68174A 23.INSTALL REAR INNER DOOR GLASS WEATHERSTRIP LH

Hide 86160Y 24.INSTALL REAR NO. 2 SPEAKER ASSEMBLY (for 12 Speakers)

Hide 67604 25.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B165684E04
2.531,1.51 2.698,1.958 2.698,1.958 2.458,1.958 false 2.167,0.875 2.792,0.167 2.792,0.167 2.417,0.167 false 0.927,0.063 2.385,0.458 1.458,0.396 10 true End Cap (Color: White) 1.021,1.854 2.49,2.156 1.469,0.302 10 true End Cap (Color: Green)

Connect the 2 cables to the inside handle.


b.
B169254E02
0.531,1 0.531,1.333 false 0.542,3.333 0.542,3.656 false 0.427,1.333 0.76,1.552 0.333,0.219 10 false Clip 0.417,3.688 0.75,3.906 0.333,0.219 10 false Clip 0.052,2.271 1.333,2.646 1.281,0.375 12 true for 12 Speakers: 0.052,0 1.167,0.406 1.115,0.406 12 true for Standard:

Attach the inside handle's knob to the door trim board.


c.

for 12 Speakers:

i.

Connect the connector.



d.

Attach the 10 clips to install the door trim board.


e.

Install the inside handle and door trim board to the door trim panel with the screw.


f.

Install the door trim board to the door panel with the screw.


g.

Install the clip.


Hide 74222A 26.INSTALL REAR DOOR ARMREST COVER LH

Hide 67674A 27.INSTALL REAR DOOR FRAME GARNISH LH

a.
B169253

Attach the 5 clips to install the rear door frame garnish.


Hide 84810D 28.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 74272A 29.INSTALL REAR UPPER DOOR ARMREST BASE PANEL LH

a.
E278383

Connect the connector.


b.
E278385

Attach the 2 clips and 5 claws to install the rear upper door armrest base panel LH.


Hide 69284D 30.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B168093

Attach the 4 claws to install the bezel plug.


Hide 31.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL