Home › Suspension › SUSPENSION › REAR LEAF SPRING
RM27M0U _53 Suspension _049152 SUSPENSION _0234400 REAR LEAF SPRING A

SUSPENSION  REAR LEAF SPRING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (see page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 48210Q 1.INSTALL REAR SPRING SHACKLE BUSH

C159334

a.

Install the 2 shackle bushes to the frame.


Hide 2.INSTALL TUBE

C156237

a.

Install the tube to the bush.


Hide 48220 3.TEMPORARILY INSTALL REAR SPRING ASSEMBLY LH

C156232E02
1.5,1.417 1.5,1.792 false 2.25,0.813 1.823,0.813 false 0.052,0.052 0.781,0.406 0.729,0.354 10 true Rear Side: 0.958,1.781 2.354,2.083 1.396,0.302 10 true Shackle Outer Plate 2.271,0.719 3.271,1.375 1,0.656 10 true No. 2 Spring Shackle Plate

a.

Temporarily install the spring with the No. 2 spring shackle plate, shackle outer plate, 2 washers and 2 nuts to the rear side.


b.
C244388E02
0.052,0.052 0.885,0.458 0.833,0.406 10 true Front Side:

Temporarily install the spring with the bolt, washer and nut to the front side.


Hide 48306 4.INSTALL REAR SPRING BUMPER SUB-ASSEMBLY

C159335E01
0.668,1.785 1.426,1.927 0.758,0.142 10 Center Bolt 1.123,1.359 1.682,0.907 false 1.123,1.359 1.123,1.771 false

a.

Install the spring bumper.

NOTICE:

Align the leaf spring center bolt and nut with the installation hole of the rear axle housing and spring bumper so that they are not loose.



Hide 48046A 5.TEMPORARILY INSTALL REAR SPRING U BOLT

C156238E02
1.188,1.563 1.281,1.708 0.094,0.146 10 true 1 2.219,1.417 2.354,1.698 0.135,0.281 10 true 2 1.667,1.781 1.781,1.927 0.115,0.146 10 false 3 1.896,1.333 2.01,1.573 0.115,0.24 10 true 4

a.

Temporarily install the spring seat and 2 U bolts with the 4 washers and 4 nuts.

NOTICE:
·

Tighten the nuts in the order shown in the illustration.

·

Install the U bolts so that the lengths of the 4 ends under the spring seat are the same.




Hide 46430 6.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

C156229E02
0.969,1.177 1.104,1.344 0.135,0.167 10 true A 2.406,1.448 2.531,1.625 0.125,0.177 10 true B 1.427,0.448 1.542,0.594 0.115,0.146 10 true A

a.

Connect the parking brake cable to the vehicle with the 3 bolts.

Torque:
for Bolt A : 19 N*m (194 kgf*cm, 14 ft.*lbf)
for Bolt B : 14 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 48220 8.TIGHTEN REAR SPRING ASSEMBLY LH

a.

Tighten the 3 nuts.

Torque:
105 N*m (1071 kgf*cm, 77 ft.*lbf)


Hide 48046A 9.TIGHTEN REAR SPRING U BOLT

a.

Tighten the 4 nuts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 10.INSTALL REAR WHEEL

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 11.INSTALL SPARE TIRE

Hide 12.REMOVE SAFETY STANDS