Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  SYSTEM DESCRIPTION  


SYSTEM DESCRIPTION


HINT:

The skid control ECU is built into the VSC actuator.


a.

ABS (Anti-lock Brake System)

The ABS helps prevent the wheels from locking when the brakes are applied firmly or on a slippery surface.

C211688E01
0.402,1.033 1.224,1.404 0.823,0.371 10 Each Speed Sensor 2.33,1.007 3.153,1.368 0.823,0.361 10 Skid Control ECU 3.916,0.776 4.711,0.981 0.795,0.205 10 Pump Motor 3.881,1.512 4.843,1.668 0.961,0.156 10 Solenoid Valve 1.915,2.838 3.481,3.021 1.566,0.184 10 Warning/Indicator Lights 3.949,2.78 5.174,2.936 1.225,0.156 10 Combination Meter 3.949,3.078 5.739,3.234 1.790,0.156 10 - ABS Warning Light 3.949,3.366 5.898,3.522 1.949,0.156 10 - SLIP Indicator Light 4.442,2.346 5.355,2.509 0.913,0.163 10 VSC Actuator 5.944,1.05 6.774,1.428 0.830,0.378 10 Each Wheel Cylinder 0.83,3.854 2.944,4.031 2.114,0.177 10 CAN Communication Line 0.83,4.148 1.972,4.304 1.142,0.156 10 Signal Line 0.83,4.463 2.180,4.619 1.350,0.156 10 Brake Fluid Pressure

i.

Operation description

The skid control ECU detects wheel lock conditions by receiving vehicle speed signals from each speed sensor, and sends control signals to the pump motor and solenoid valve to prevent the wheels from locking by controlling the brake fluid pressure of each wheel cylinder.

The ABS warning light and SLIP indicator light come on when the ABS system malfunctions.



b.

EBD (Electronic Brake Force Distribution)

The EBD control utilizes the ABS, performing proper brake force distribution between the front and rear wheels in accordance with the driving conditions. When the brakes are applied while cornering, it also controls the braking forces of the rear right and rear left wheels, helping to maintain vehicle stability.

C152734E03
0.419,1.359 1.241,1.730 0.823,0.371 10 Each Speed Sensor 2.338,1.38 3.189,1.702 0.850,0.323 10 Skid Control ECU 3.83,1.513 4.792,1.669 0.961,0.156 10 Solenoid Valve 1.93,3.159 3.467,3.343 1.538,0.184 10 Warning/Indicator Lights 3.851,2.944 5.077,3.100 1.225,0.156 10 Combination Meter 3.851,3.201 5.338,3.357 1.487,0.156 10 - ABS Warning Light 3.851,3.444 5.412,3.600 1.561,0.156 10 - BRAKE Warning Light 3.851,3.682 5.195,3.838 1.343,0.156 10 - SLIP Indicator Light 5.354,2.501 6.246,2.663 0.892,0.163 10 VSC Actuator 5.967,1.338 6.796,1.716 0.830,0.378 10 Each Wheel Cylinder 1.119,3.842 2.789,4.019 1.670,0.177 10 CAN Communication Line 1.098,4.137 2.796,4.292 1.698,0.156 10 Signal Line 1.098,4.452 2.449,4.608 1.350,0.156 10 Brake Fluid Pressure

i.

Operation description

The skid control ECU receives speed signals from each speed sensor to detect the slip conditions of the wheels and sends control signals to the solenoid.

The solenoid valve controls the brake fluid pressure of each wheel cylinder, and divides the control power properly between the front and rear wheels and the rear right and rear left wheels.

The ABS and BRAKE warning lights and SLIP indicator light come on to indicate malfunctions in the EBD system.



c.

BA (Brake Assist)

The primary purpose of the brake assist system is to provide auxiliary brake force to assist drivers who cannot generate a brake force large enough during emergency braking, thus helping to maximize the vehicle's braking performance.

C152735E04
0.434,1.514 1.257,1.885 0.823,0.371 10 Each Speed Sensor 2.281,1.566 3.205,1.921 0.924,0.355 10 Skid Control ECU 3.986,1.22 4.781,1.425 0.795,0.205 10 Pump Motor 3.888,1.935 4.849,2.090 0.961,0.156 10 Solenoid Valve 5.455,3.469 6.347,3.632 0.892,0.163 10 VSC Actuator 5.982,1.493 6.812,1.871 0.830,0.378 10 Each Wheel Cylinder 1.114,4.688 2.784,4.864 1.670,0.177 10 CAN Communication Line 1.093,4.982 2.790,5.138 1.698,0.156 10 Signal Line 1.093,5.297 2.443,5.453 1.350,0.156 10 Brake Fluid Pressure 3.825,2.441 4.911,3.058 1.086,0.617 10 Master Cylinder Brake Fluid Pressure Sensor 1.941,3.985 3.479,4.169 1.538,0.184 10 Warning/Indicator Lights 3.748,3.919 4.974,4.075 1.225,0.156 10 Combination Meter 3.748,4.176 5.235,4.332 1.487,0.156 10 - ABS Warning Light 3.748,4.419 5.108,4.575 1.360,0.156 10 - SLIP Indicator Light

i.

Operation description

The skid control ECU receives speed signals from each speed sensor and the fluid pressure signal from the master cylinder pressure sensor to determine whether brake assist is necessary. If brake assist is deemed necessary, the skid control ECU sends control signals to the pump motor and solenoid. The pump and the solenoid valve then control the pressure applied to each wheel cylinder. The ABS warning light and the SLIP indicator light come on to indicate malfunctions in the BA system.



d.

Changing of TRAC, AUTO LSD and VSC operation permission / disablement through VSC OFF switch

i.
C152736E01
0.085,0.008 1.193,0.164 1.107,0.156 10 VSC OFF Switch

Changing modes

Through the VSC OFF switch, the vehicle can be changed to normal mode, TRAC OFF mode, AUTO LSD mode and VSC OFF mode.

C179467E03
4.938,1.76 6.063,1.958 1.125,0.198 10 false TRAC OFF mode 2.854,0.927 3.833,1.188 0.979,0.26 10 false Normal mode 2.74,2.698 3.927,2.958 1.188,0.26 10 false AUTO LSD mode 0.76,1.802 1.833,2.021 1.073,0.219 10 false VSC OFF mode 0.542,0 1.5,0.208 0.958,0.208 10 false Switch Control 0.531,0.323 3.531,0.542 3,0.219 10 false 2WD vehicles and 4WD vehicles in 2H mode: 1.208,3.469 4.823,3.677 3.615,0.208 10 false : VSC OFF switch is pressed for a short amount of time 1.219,3.854 5.979,4.073 4.76,0.219 10 false : Vehicle is stopped and VSC OFF switch is pressed for 3 seconds or more 1.208,4.208 7.042,4.458 5.833,0.25 10 false : VSC OFF switch is pressed for a short amount of time or the ignition switch is turned off

2WD vehicles and 4WD vehicles in 2H mode
Control Mode Indicator Light
TRAC OFF Indicator Light*1 TRAC OFF Indicator*2 AUTO LSD Indicator Light VSC OFF Indicator Light
Normal mode - - - -
TRAC OFF mode - - ○ -
AUTO LSD mode - - ○ ○
VSC OFF mode ○ ○ - ○

*1: w/o Multi-information Display

*2: w/ Multi-information Display


HINT:
·

○: Illuminated

·

-: Not illuminated



C212001E02
4.948,1.813 6.073,2.01 1.125,0.198 10 false TRAC OFF mode 2.865,0.99 3.844,1.25 0.979,0.26 10 false Normal mode 0.771,1.854 1.844,2.073 1.073,0.219 10 false VSC OFF mode 0.552,0.052 1.51,0.26 0.958,0.208 10 false Switch Control 0.542,0.385 2.313,0.552 1.771,0.167 10 false 4WD vehicles in H4L mode: 1.271,2.604 4.885,2.813 3.615,0.208 10 false : VSC OFF switch is pressed for a short amount of time 1.25,2.958 6.01,3.177 4.76,0.219 10 false : Vehicle is stopped and VSC OFF switch is pressed for 3 seconds or more 1.25,3.323 6.781,3.521 5.531,0.198 10 false : VSC OFF switch is pressed for a short amount of time or the ignition switch is turned off

4WD vehicles in H4L mode
Control Mode Indicator Light
TRAC OFF Indicator Light*1 TRAC OFF Indicator*2 VSC OFF Indicator Light
Normal mode - - -
TRAC OFF mode ○ ○ -
VSC OFF mode ○ ○ ○

*1: w/o Multi-information Display

*2: w/ Multi-information Display


HINT:
·

○: Illuminated

·

-: Not illuminated



C179469E05
0.979,0.948 1.958,1.208 0.979,0.26 10 false Normal mode 4.958,0.99 6.031,1.208 1.073,0.219 10 false VSC OFF mode 0.594,0.021 1.552,0.229 0.958,0.208 10 false Switch Control 0.583,0.354 2.344,0.531 1.76,0.177 10 false 4WD vehicles in L4L mode: 0.979,1.885 5.74,2.104 4.76,0.219 10 false : Vehicle is stopped and VSC OFF switch is pressed for 3 seconds or more 1,2.25 6.802,2.5 5.802,0.25 10 false : VSC OFF switch is pressed for a short amount of time or the ignition switch is turned off

4WD vehicles in L4L mode
Control Mode Indicator Light
TRAC OFF Indicator Light*1 TRAC OFF Indicator*2 VSC OFF Indicator Light
Normal mode - - ○
VSC OFF mode ○ ○ ○

*1: w/o Multi-information Display

*2: w/ Multi-information Display


HINT:
·

○: Illuminated

·

-: Not illuminated




ii.

Drive mode and each function

Drive Mode VSC OFF Switch Brake Control
ABS EBD BA TRAC A-TRAC AUTO LSD VSC
2WD vehicles and 4WD vehicles in 2H mode Normal mode ○ ○ ○ ○ - - ○
TRAC OFF mode ○ ○ ○ - - ○ ○
AUTO LSD mode ○ ○ ○ - - ○ -
VSC OFF mode ○ ○ ○ - - - -
4WD vehicles in H4L mode Normal mode ○ ○ ○ - ○ - ○
TRAC OFF mode ○ ○ ○ - - - ○
VSC OFF mode ○ ○ ○ - - - -
4WD vehicles in L4L mode Normal mode ○ ○ ○ - ○ - -
VSC OFF mode ○ ○ ○ - - - -

HINT:
·

○: Operates

·

-: Does not operate





e.

TRAC (Traction Control) (for 2WD vehicles or 4WD vehicles in 2H mode)

The TRAC system helps prevent the drive wheels from slipping if the driver presses down on the accelerator pedal excessively when starting off or accelerating on a slippery surface.

C295409E01
0.226,1.197 1.044,1.568 0.818,0.371 10 Each Speed Sensor 0.224,0.5 1.352,0.719 1.128,0.218 10 VSC OFF Switch 2.284,0.953 3.092,1.285 0.809,0.332 10 Skid Control ECU 3.738,1.841 4.533,2.045 0.795,0.205 10 Pump Motor 3.743,2.607 4.705,2.763 0.961,0.156 10 Solenoid Valve 5.538,3.366 6.780,3.706 1.243,0.340 10 VSC OFF Indicator Light 5.671,4.137 6.596,4.477 0.925,0.340 10 SLIP Indicator Light 5.67,4.907 6.618,5.247 0.948,0.340 10 AUTO LSD Indicator Light 5.538,2.613 6.840,2.943 1.302,0.330 10 TRAC OFF Indicator Light*1 3.092,3.268 3.991,3.431 0.899,0.163 10 VSC Actuator 5.94,1.768 6.770,2.146 0.830,0.378 10 Each Wheel Cylinder 1.012,5.026 2.682,5.203 1.670,0.177 10 CAN Communication Line 1.012,5.32 2.709,5.476 1.698,0.156 10 Signal Line 1.012,5.636 2.362,5.791 1.350,0.156 10 Brake Fluid Pressure 0.315,3.396 1.263,3.802 0.948,0.406 10 Steering Angle Sensor 0.567,4.251 0.945,4.448 0.378,0.198 10 ECM 0.217,1.967 1.220,2.442 1.003,0.475 10 Yaw Rate and Deceleration Sensor 5.618,6.465 6.830,6.621 1.211,0.156 10 Combination Meter 3.652,0.476 4.727,1.018 1.075,0.541 10 Master Cylinder Brake Fluid Pressure Sensor 5.389,5.687 6.971,6.047 1.582,0.360 10 Multi-information Display -TRAC OFF Indicator*2 0.409,5.934 2.472,6.137 2.063,0.202 10 *1: w/o Multi-information Display 0.409,6.224 2.472,6.426 2.063,0.202 10 *2: w/ Multi-information Display

i.

Operation description

The skid control ECU detects the vehicle's slip condition by receiving signals from each speed sensor and the ECM via CAN communication.

The skid control ECU controls engine torque with the ECM via CAN communication and brake fluid pressure through the pump and solenoid valve. The SLIP indicator light blinks when the system is operating. The SLIP indicator light comes on when the TRAC system malfunctions.



f.

VSC (Vehicle Stability Control)

The VSC system helps prevent the vehicle from slipping sideways when front or rear wheel skidding occurs while cornering.

C295241E01
0.184,1.088 1.480,1.459 1.297,0.371 10 Each Speed Sensor 0.212,0.343 1.340,0.561 1.128,0.218 10 VSC OFF Switch 2.117,0.856 2.926,1.189 0.809,0.332 10 Skid Control ECU 3.96,1.604 4.754,1.808 0.795,0.205 10 Pump Motor 3.862,2.286 4.823,2.442 0.961,0.156 10 Solenoid Valve 5.302,4.142 6.561,4.482 1.259,0.340 10 VSC OFF Indicator Light 5.253,4.975 6.519,5.186 1.266,0.211 10 SLIP Indicator Light 5.099,5.642 6.761,5.981 1.663,0.340 10 Multi-information Display -TRAC OFF Indicator*2 5.263,3.396 6.593,3.725 1.330,0.330 10 TRAC OFF Indicator Light*1 3.08,3.171 3.979,3.334 0.899,0.163 10 VSC Actuator 6.058,1.858 6.888,2.236 0.830,0.378 10 Each Wheel Cylinder 0.997,5.013 2.667,5.189 1.670,0.177 10 CAN Communication Line 0.997,5.307 2.695,5.463 1.698,0.156 10 Signal Line 0.997,5.622 2.348,5.778 1.350,0.156 10 Brake Fluid Pressure 0.303,3.429 1.250,3.835 0.948,0.406 10 Steering Angle Sensor 0.555,4.312 0.933,4.509 0.378,0.198 10 ECM 0.205,1.87 1.208,2.345 1.003,0.475 10 Yaw Rate and Deceleration Sensor 5.438,6.477 6.649,6.633 1.211,0.156 10 Combination Meter 3.77,0.38 4.845,0.921 1.075,0.541 10 Master Cylinder Brake Fluid Pressure Sensor 0.439,5.962 2.553,6.146 2.114,0.184 10 *1: w/o Multi-information Display 0.439,6.278 2.553,6.461 2.114,0.184 10 *2: w/ Multi-information Display

i.

Operation description

The skid control ECU determines the vehicle condition by receiving signals from the speed sensor, yaw rate and deceleration sensor and steering angle sensor. The skid control ECU controls driving torque with the ECM via CAN communication, and brake fluid pressure with the solenoid valve.

The SLIP indicator light blinks when the system is operating. When there is a malfunction in the VSC system, the SLIP indicator light comes on.

The VSC OFF switch stops VSC operation.



g.

A-TRAC (Active Traction Control) (for 4WD)

During rugged off-road driving, this system controls the engine output and the brake fluid pressure that is applied to the slipping wheel and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an LSD (Limited Slip Differential) effect.

HINT:

The A-TRAC system operates when the 4WD control switch is set to 4L or 4H.


C295241E01
0.184,1.088 1.480,1.459 1.297,0.371 10 Each Speed Sensor 0.212,0.343 1.340,0.561 1.128,0.218 10 VSC OFF Switch 2.117,0.856 2.926,1.189 0.809,0.332 10 Skid Control ECU 3.96,1.604 4.754,1.808 0.795,0.205 10 Pump Motor 3.862,2.286 4.823,2.442 0.961,0.156 10 Solenoid Valve 5.302,4.142 6.561,4.482 1.259,0.340 10 VSC OFF Indicator Light 5.253,4.975 6.519,5.186 1.266,0.211 10 SLIP Indicator Light 5.099,5.642 6.761,5.981 1.663,0.340 10 Multi-information Display -TRAC OFF Indicator*2 5.263,3.396 6.593,3.725 1.330,0.330 10 TRAC OFF Indicator Light*1 3.08,3.171 3.979,3.334 0.899,0.163 10 VSC Actuator 6.058,1.858 6.888,2.236 0.830,0.378 10 Each Wheel Cylinder 0.997,5.013 2.667,5.189 1.670,0.177 10 CAN Communication Line 0.997,5.307 2.695,5.463 1.698,0.156 10 Signal Line 0.997,5.622 2.348,5.778 1.350,0.156 10 Brake Fluid Pressure 0.303,3.429 1.250,3.835 0.948,0.406 10 Steering Angle Sensor 0.555,4.312 0.933,4.509 0.378,0.198 10 ECM 0.205,1.87 1.208,2.345 1.003,0.475 10 Yaw Rate and Deceleration Sensor 5.438,6.477 6.649,6.633 1.211,0.156 10 Combination Meter 3.77,0.38 4.845,0.921 1.075,0.541 10 Master Cylinder Brake Fluid Pressure Sensor 0.439,5.962 2.553,6.146 2.114,0.184 10 *1: w/o Multi-information Display 0.439,6.278 2.553,6.461 2.114,0.184 10 *2: w/ Multi-information Display

i.

Operation description

The SLIP indicator light blinks when the system is operating. The SLIP indicator light comes on to indicate a malfunction in the A-TRAC system.



h.

AUTO LSD (Auto Limited Slip Differential)

For 2WD vehicles and 4WD vehicles in 2H mode, the AUTO LSD will operate with the VSC OFF switch on (approximately 1 second) and the accelerator pedal depressed.

The AUTO LSD system is used to restrain brake pressure and reduce differential movement, thus transmitting drive torque to the other drive wheel to ensure startability under the following conditions:

·

Wheels run off the road.

·

Drive wheels slip when starting on a slope with one wheel on snow/ice.


HINT:

Depressing the brake pedal cancels control of the AUTO LSD system.


C247663E03
0.439,0.98 1.261,1.351 0.823,0.371 10 Each Speed Sensor 0.299,0.21 1.427,0.428 1.128,0.218 10 VSC OFF Switch 2.358,0.723 3.167,1.055 0.809,0.332 10 Skid Control ECU 3.97,1.534 4.765,1.738 0.795,0.205 10 Pump Motor 3.949,2.377 4.910,2.533 0.961,0.156 10 Solenoid Valve 5.822,3.529 6.727,3.869 0.905,0.340 10 VSC OFF Indicator Light 5.801,2.709 6.748,3.049 0.948,0.340 10 AUTO LSD Indicator Light 5.811,4.287 6.738,4.617 0.927,0.330 10 SLIP Indicator Light 3.167,3.038 4.066,3.201 0.899,0.163 10 VSC Actuator 5.938,1.755 6.768,2.133 0.830,0.378 10 Each Wheel Cylinder 1.14,4.79 2.810,4.967 1.670,0.177 10 CAN Communication Line 1.14,5.084 2.838,5.240 1.698,0.156 10 Signal Line 1.14,5.4 2.491,5.555 1.350,0.156 10 Brake Fluid Pressure 0.366,3.182 1.314,3.588 0.948,0.406 10 Steering Angle Sensor 0.642,4.021 1.020,4.218 0.378,0.198 10 ECM 0.292,1.764 1.295,2.240 1.003,0.475 10 Yaw Rate and Deceleration Sensor 5.693,5.148 6.904,5.304 1.211,0.156 10 Combination Meter 3.846,0.286 4.921,0.827 1.075,0.541 10 Master Cylinder Brake Fluid Pressure Sensor

i.

Operation description

The SLIP indicator light blinks and the AUTO LSD indicator light remains on when the system is operating.

The SLIP indicator light comes on to indicate a malfunction in the AUTO LSD system.

When the vehicle is in normal mode and the VSC OFF switch is pressed for 3 seconds or more, AUTO LSD operation becomes possible. During AUTO LSD mode, the combination meter's AUTO LSD indicator light and VSC OFF indicator light illuminate, and TRAC operation is disabled.

When the vehicle speed is more than 50 km/h (31 mph), the vehicle automatically returns to normal mode. When the vehicle speed is 50 km/h (31 mph) or less, the vehicle returns to AUTO LSD mode.



i.

Trailer Sway Control

Trailer sway control is a part of VSC. If the vehicle is towing a trailer with an inappropriate hitch load, trailer sway could be caused by crosswinds, imbalance caused by the load, or the driver's steering. Trailer sway control reduces trailer sway by controlling the engine output and the braking of each wheel.



ABS with EBD, BA, TRAC and VSC OPERATION


a.

The skid control ECU calculates vehicle stability tendency based on the signals from the 4 wheel speed sensors, the yaw rate and deceleration sensor and the steering angle sensor. In addition, it evaluates the results of the calculations to determine whether any control actions (control of the engine output torque by electronic throttle control and of the brake fluid pressure by the VSC actuator) should be implemented.


b.

The SLIP indicator light blinks to inform the driver that the VSC system is operating. The SLIP indicator light also blinks when traction control is operating, and the operation being performed is displayed.



FAIL-SAFE FUNCTION


a.

When a failure occurs in the ABS with BA, TRAC and VSC systems, the ABS warning light and SLIP indicator light come on, and the operation of those systems is prohibited. In addition to this, when a failure which disables the EBD operation occurs, the BRAKE warning light comes on and EBD operation is prohibited.


b.

If control is prohibited due to a malfunction during operation, control is disabled gradually to avoid sudden vehicle instability.


c.

w/o Multi-information Display:

When there is an engine failure related to VSC, VSC continues as much as possible and the TRAC OFF indicator light comes on.

w/ Multi-information Display:

When there is an engine failure related to VSC, VSC continues as much as possible and TRAC OFF is displayed on the multi-information display.



INITIAL CHECK


a.

When the vehicle speed first reaches approximately 23 km/h (14 mph) or more after the ignition switch is turned ON, each solenoid valve and the motor of the VSC actuator are sequentially activated to perform electrical checks. During the initial check, the operating sound of the motor can be heard from the engine compartment, but this does not indicate a malfunction.



FUNCTION OF COMPONENTS


Components Functions
Front speed sensor
(Semiconductor speed sensor, magnetic sensor rotor)
·

Detects the wheel speed and sends a signal to the skid control ECU.

·

The magnetic sensor rotor is equipped with north and south poles (48 poles each), which are evenly spaced around its circumference.

·

The magnetic field changes as the magnetic sensor rotor rotates. The semiconductor speed sensor detects the change and outputs it as the vehicle speed pulse.


Rear control sensor
(Semiconductor speed sensor, magnetic sensor rotor)
·

The skid control sensor (semiconductor speed sensor) and the sensor rotor (magnetic sensor rotor) are installed on the rear axle carrier.

·

The skid control sensor has the same structure and functions as the front speed sensor.


Skid control ECU
(Housed in VSC actuator)
·

Processes the signals from each sensor to control the ABS, BA, TRAC, and VSC.

·

Sends and receives control signals to and from the ECM, yaw rate and deceleration sensor, steering angle sensor, etc. via CAN communication.


VSC actuator
·

Consists of the master cylinder cut solenoid valve, holding solenoid valve, pressure reduction solenoid valve, pump motor, and reservoir, and adjusts the brake fluid pressure applied to each wheel cylinder.

·

Houses the skid control ECU.


Motor relay
·

Supplies power source to the pump motor.

·

Housed in the skid control ECU.


Solenoid relay
·

Supplies power to each solenoid.

·

Housed in the skid control ECU.


Steering angle sensor
·

Detects the steering extent and direction and sends signals to the skid control ECU via CAN communication.

·

Has a magnetic resistance element which detects the rotation of the magnet housed in the detection gear in order to detect the changes in magnetic resistance and the steering amount and direction.


Yaw rate and deceleration sensor
·

Yaw rate sensor detects the vehicle's angular velocity (yaw rate) in the vertical direction based on the extent and direction of the quartz tuning fork due to the Coriolis force.

·

Deceleration sensor measures the capacity of the condenser that changes with the distance between the electrodes depending on G force, which occurs when the vehicle is accelerated, and converts the measured value into electrical signals.

·

Sends signals to the skid control ECU via CAN communication.


Master cylinder brake fluid pressure sensor
·

Detects the brake fluid pressure in the master cylinder.

·

Housed in the VSC actuator.


ECM

Controls the engine output when TRAC and VSC are operating with the skid control ECU via CAN communication.


VSC OFF indicator light

Illuminates to inform the driver when VSC OFF mode or AUTO LSD mode is entered.


TRAC OFF indicator light*1
·

Illuminates to inform the driver when VSC OFF mode is entered.

·

for 4WD: Illuminates to inform the driver when TRAC OFF mode is entered.


TRAC OFF indicator*2
·

Displays to inform the driver when VSC OFF mode is entered.

·

for 4WD: Displays to inform the driver when TRAC OFF mode is entered.


VSC OFF switch

For 2WD vehicles or 4WD vehicles in 2H mode: Operation of the VSC OFF switch changes the vehicle from normal mode to TRAC OFF mode to AUTO LSD mode to VSC OFF mode.

For 4WD vehicles in 4H or 4L mode: Operation of the VSC OFF switch changes the vehicle from normal mode to VSC OFF mode.


ABS warning light
·

Illuminates to inform the driver that a malfunction in the ABS has occurred.

·

Blinks to indicate DTCs that relate to the ABS.


BRAKE warning light
·

Illuminates to inform the driver that the parking brake is ON when the system is normal, and when the amount of brake fluid has decreased.

·

Illuminates to inform the driver that a malfunction in the EBD has occurred.


SLIP indicator light
·

Illuminates to inform the driver when the engine has failed. However, VSC continues as much as possible.

·

Blinks to inform the driver that TRAC, VSC, AUTO LSD or trailer sway control is operating.

·

Illuminates to inform the driver that a malfunction has occurred in the TRAC or VSC system.

·

Blinks to indicate DTCs that relate to the VSC.


AUTO LSD indicator light Illuminates to inform the driver that the AUTO LSD is ready to operate.
Stop light control relay
(BRK NO. 1)
Receives a signal from the skid control ECU and illuminates the stop light when the vehicle decelerates due to trailer sway control.
Stop light control relay
(BRK NO. 2)
Because the brake pedal could move down when the VSC system is activated (booster solenoid is turned ON) even though the driver is not depressing the brake pedal, this relay prevents the stop light from turning ON.

*1: w/o Multi-information Display

*2: w/ Multi-information Display