Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TEST MODE PROCEDURE  


HINT:
·

By switching the skid control ECU from normal mode to test mode, abnormality detection sensitivity is enhanced and troubleshooting can be conducted efficiently.

·

Perform a sensor check in test mode after the speed sensor or sensor rotor has been repaired or replaced.

·

If the ignition switch is turned from ON to ACC or off during test mode, DTCs related to the signal check function will not be erased. During test mode, do not change to normal mode.

·

During test mode, the skid control ECU stores all DTCs related to the signal check function, and the DTCs are erased if normality is confirmed. Any remaining DTCs indicate abnormalities that were found.



TEST MODE (SIGNAL CHECK) PROCEDURE (WHEN USING TECHSTREAM)


a.

Place the vehicle on a level surface with an inclination of less than +/-1°.


b.

Turn the ignition switch off.


c.

Check that the steering wheel is in the centered position.


d.

Check that the shift lever is in parking or neutral and apply the parking brake.

CAUTION:

Application of the parking brake is not necessary for entering test mode. However, apply the parking brake for safety.



e.

Connect the Techstream to the DLC3.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Switch the skid control ECU to test mode using the Techstream.

Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.


i.
C353023E01
0.031,0.042 2.115,0.25 2.083,0.208 10 false Blinking pattern in TEST MODE: 0.427,0.583 1.156,0.781 0.729,0.198 10 false 0.125 sec. 2.052,0.594 2.781,0.792 0.729,0.198 10 false 0.125 sec. 0.219,0.906 0.521,1.073 0.302,0.167 10 false ON 0.24,1.708 0.563,1.875 0.323,0.167 10 false OFF

Check that the ABS warning light and SLIP indicator light blink as shown in the illustration.


j.

Start the engine.



TEST MODE (SIGNAL CHECK) PROCEDURE (WHEN USING SST CHECK WIRE)


a.

Place the vehicle on a level surface with an inclination of less than +/-1°.


b.

Turn the ignition switch off.


c.

Check that the steering wheel is in the centered position.


d.

Check that the shift lever is in parking or neutral and apply the parking brake.

CAUTION:

Application of the parking brake is not necessary for entering test mode. However, apply the parking brake for safety.



e.
H102392E80
2.367,0.304 2.600,0.454 0.234,0.150 10 CG 1.605,0.895 2.265,0.457 false 1.128,1.809 1.358,1.974 0.230,0.165 10 TS 1.579,1.435 1.242,1.809 false 0.092,0.03 1.396,0.204 1.304,0.174 10 Front view of DLC3:

Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  


f.

Turn the ignition switch to ON.


g.
C353023E01
0.031,0.042 2.115,0.25 2.083,0.208 10 false Blinking pattern in TEST MODE: 0.427,0.583 1.156,0.781 0.729,0.198 10 false 0.125 sec. 2.052,0.594 2.781,0.792 0.729,0.198 10 false 0.125 sec. 0.219,0.906 0.521,1.073 0.302,0.167 10 false ON 0.24,1.708 0.563,1.875 0.323,0.167 10 false OFF

Check that the ABS warning light and SLIP indicator light blink as shown in the illustration.


h.

Start the engine.



MASTER CYLINDER PRESSURE SENSOR CHECK


a.

Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.

HINT:

If the sensor check has been completed normally, DTC C1281/81 is cleared and the ABS warning light turns on for 3 seconds.




DECELERATION SENSOR CHECK


a.

Release the parking brake and drive the vehicle at a speed of 3 km/h (2 mph) or more, and turn the steering wheel either to the left or right 90° or more to turn the vehicle 180°.

HINT:
·

The skid control ECU checks whether the lateral acceleration reaches 0.1 G or more while the vehicle is turning.

·

The table shows the vehicle speeds and turning radius under which the lateral acceleration reaches 0.1 G or more.

Reference
Vehicle Speed
km/h (mph)
Turning Radius
m (ft.)
10 (6) 7.87 (25.82)
15 (9) 17.72 (58.13)
20 (12) 31.49 (103.31)
25 (16) 49.21 (161.45)

·

If the sensor check has been completed normally, DTC C1279/79 is cleared.

·

Do not spin the wheels.





SPEED SENSOR CHECK


a.
C353023E01
0.031,0.042 2.115,0.25 2.083,0.208 10 false Blinking pattern in TEST MODE: 0.427,0.583 1.156,0.781 0.729,0.198 10 false 0.125 sec. 2.052,0.594 2.781,0.792 0.729,0.198 10 false 0.125 sec. 0.219,0.906 0.521,1.073 0.302,0.167 10 false ON 0.24,1.708 0.563,1.875 0.323,0.167 10 false OFF

Check that the ABS warning light is blinking as shown in the illustration.


b.

Check the forward signal.

U152352E02
2.51,4.021 3.063,4.021 3.063,4.021 3.063,3.448 false 2.823,0.906 2.823,0.49 2.823,0.49 2.99,0.49 false 1.74,2.385 1.74,1.635 1.74,1.635 1.833,1.635 false 3.5,1.698 3.5,1.375 3.5,1.375 3.208,1.271 false 6.042,1.573 6.125,1.573 6.125,1.573 6.448,2.063 false 4.813,2.385 4.906,1.969 4.906,1.969 4.948,1.969 false 0.073,0.083 2.594,0.292 2.521,0.208 10 false Light illumination pattern when normal: 0.448,0.823 1.448,1.188 1,0.365 10 false Vehicle Speed (km/h) 3.042,0.417 4.656,0.615 1.615,0.198 10 false Do not spin the wheels 1.885,1.563 2.51,1.958 0.625,0.396 10 false Vehicle stopped 5,1.875 6.063,2.073 1.063,0.198 10 false Vehicle stopped 3.219,1.75 4.281,1.938 1.063,0.188 10 false Driving forward 5.583,1.448 6.156,1.646 0.573,0.198 10 false Driving 0.25,2.625 1.25,2.833 1,0.208 10 false Light Condition 0.708,3.958 2.469,4.323 1.76,0.365 10 false Sensor check completion 45 km/h (28 mph) or more 1.24,2.885 1.531,3.094 0.292,0.208 10 false ON 1.219,3.25 1.552,3.458 0.333,0.208 10 false OFF 1.365,1.292 1.563,1.479 0.198,0.188 10 false 45 1.438,2.427 1.583,2.615 0.146,0.188 10 false 0

i.

Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

NOTICE:

The signal check may not be completed if the vehicle has its wheels spun or the steering wheel is turned during this check.




c.

Stop the vehicle.

NOTICE:
·

The speed sensor signal check may not be completed if the speed sensor signal check is started while turning the steering wheel or spinning the wheels.

·

If the signal check has not been completed, the ABS warning light blinks while driving and the ABS system does not operate.



HINT:

When the signal check has been completed, the ABS warning light turns off while driving and blinks in the test mode pattern while stationary.




READ SIGNAL CHECK FUNCTION DTCs (WHEN USING TECHSTREAM)


a.

Read the DTC(s) by following the instructions on the Techstream screen.



READ SENSOR SIGNAL CHECK FUNCTION DTCs (WHEN USING SST CHECK WIRE)


a.
H102392E93
2.289,0.304 2.522,0.454 0.234,0.150 10 CG 1.605,0.895 2.265,0.457 false 1.128,1.809 1.358,1.974 0.230,0.165 10 TS 1.579,1.435 1.242,1.809 false 1.917,1.809 2.147,1.974 0.230,0.165 10 TC 1.81,1.435 2.032,1.809 false 0.079,0.061 1.420,0.273 1.341,0.211 10 Front view of DLC3:

Using SST, connect terminals 4 (CG), 12 (TS) and 13 (TC) of the DLC3.

SST
09843-18040  


b.

Turn the ignition switch to ON.


c.

Read the number of blinks of the ABS warning light.

HINT:
C353023E02
0.031,0.042 2.115,0.25 2.083,0.208 10 false Normal System Code: 0.427,0.583 1.156,0.781 0.729,0.198 10 false 0.25 sec. 2.052,0.594 2.781,0.792 0.729,0.198 10 false 0.25 sec.

If all sensors are normal, a normal system code is output (the light comes on at 0.25 second intervals).



d.

After the check, disconnect SST from terminals 4 (CG), 12 (TS) and 13 (TC) of the DLC3.


e.

Turn the ignition switch off.



SENSOR SIGNAL CHECK FUNCTION DTCs


ABS sensor:
DTC Code Diagnosis Trouble Areas
C1271/71 Low output signal of front speed sensor RH
·

Front speed sensor RH

·

Speed sensor circuit

·

Sensor installation


C1272/72 Low output signal of front speed sensor LH
·

Front speed sensor LH

·

Speed sensor circuit

·

Sensor installation


C1273/73 Low output signal of rear speed sensor RH
·

Rear speed sensor RH

·

Speed sensor circuit

·

Sensor installation


C1274/74 Low output signal of rear speed sensor LH
·

Rear speed sensor LH

·

Speed sensor circuit

·

Sensor installation


C1275/75 Abnormal change in output signal of front speed sensor RH
·

Sensor installation

·

Speed sensor rotor

·

Foreign matter on sensor tip or sensor rotor


C1276/76 Abnormal change in output signal of front speed sensor LH
·

Sensor installation

·

Speed sensor rotor

·

Foreign matter on sensor tip or sensor rotor


C1277/77 Abnormal change in output signal of rear speed sensor RH
·

Sensor installation

·

Speed sensor rotor

·

Foreign matter on sensor tip or sensor rotor


C1278/78 Abnormal change in output signal of rear speed sensor LH
·

Sensor installation

·

Speed sensor rotor

·

Foreign matter on sensor tip or sensor rotor


C1279/79 Deceleration sensor output voltage malfunction
·

Yaw rate sensor and deceleration sensor

·

Sensor installation


C1281/81 Master cylinder pressure sensor output malfunction
·

Master cylinder brake fluid pressure sensor

·

Master cylinder brake fluid pressure sensor circuit

·

Stop light switch circuit

·

VSC actuator (skid control ECU)

·

Brake booster assembly



HINT:
·

The DTCs in this table are only output in test mode.

·

Detection of DTCs from C1271/71 to C1274/74 is completed before the vehicle speed reaches 5 km/h (3 mph).

·

Detection of DTCs from C1275/75 to C1278/78 is completed before the vehicle speed reaches 45 km/h (28 mph).

·

C1271/71 to C1274/74: Speed sensor output from only one wheel is extremely low despite the other wheel speed outputs reaching 5 km/h (3 mph).

·
F100272E05
0.023,0 0.812,0.208 0.789,0.208 10 Example: 0.035,0.514 0.668,0.715 0.634,0.201 10 Normal 0.035,1.265 0.824,1.466 0.789,0.201 10 Abnormal

C1275/75 to C1278/78: Abnormal speed sensor output frequency is as shown in the illustration.