Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234402 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

In case of replacing the skid control ECU, perform the zero point calibration of the steering angle sensor, master cylinder pressure sensor, and yaw rate and deceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

Hide 44540 1.INSTALL VSC ACTUATOR WITH ACTUATOR BRACKET ASSEMBLY

a.
C155484E01
0.959,1.726 1.073,1.887 0.114,0.161 10 A 0.976,0.358 1.090,0.519 0.114,0.161 10 B 3.088,0.919 3.220,1.080 0.133,0.161 10 C

Install the VSC actuator with actuator bracket with the 3 nuts.

NOTICE:

Do not drop the actuator. If dropped, replace it.



b.

Tighten the 3 nuts uniformly in alphabetical order.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 47312 2.CONNECT BRAKE TUBE

a.
U152153E01
0.347,1.407 0.528,1.553 0.181,0.147 10 *2 0.383,2.224 0.544,2.371 0.161,0.147 10 *4 2.573,1.353 2.755,1.518 0.181,0.165 10 *3 1.009,0.437 1.186,0.616 0.177,0.179 10 *5 0.348,0.07 0.533,0.249 0.185,0.179 10 *6 1.485,0.757 1.666,0.923 0.181,0.165 10 *1 1.544,2.203 0.644,1.487 0.644,1.487 0.547,1.487 false 1.714,2.476 0.574,2.316 false 2.052,1.577 2.172,1.434 2.172,1.434 2.556,1.434 false

Set each brake line to the correct position on the brake actuator as shown in the illustration.

HINT:
·

*1: FR RH

·

*2: FR LH

·

*3: RR RH

·

*4: RR LH

·

*5: FR Master Cylinder

·

*6: RR Master Cylinder




b.

Install a new clamp onto the VSC actuator bracket.


c.
C208908

Using a union nut wrench, connect the 4 brake tubes.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 47311 3.INSTALL BRAKE TUBE

a.
C208907

Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



b.
C208906

Using a union nut wrench, connect the 2 brake tubes to the VSC actuator.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 44540 4.CONNECT VSC ACTUATOR CONNECTOR

a.
C154435

Connect the VSC actuator connector.


Hide 28800 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 6. BLEED BRAKE SYSTEM