Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › FRONT SPEED SENSOR
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234403 FRONT SPEED SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  FRONT SPEED SENSOR  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 42603 3.REMOVE FRONT WHEEL

Hide 89516 4.REMOVE FRONT SKID CONTROL SENSOR WIRE LH

a.
C154445E01
2.226,4.049 2.344,4.201 0.118,0.152 10 A 1.345,3.236 1.463,3.389 0.118,0.152 10 B 0.718,3.095 0.836,3.247 0.118,0.152 10 B 1.474,3.503 1.592,3.655 0.118,0.152 10 B 0.078,2.472 0.195,2.624 0.118,0.152 10 C

Disconnect the connector (labeled A) from the front speed sensor.


b.

Detach the 3 clips (labeled B) and remove the clamp bolt (labeled C).


c.
C154447E03
2.323,0.417 2.448,0.573 0.125,0.156 10 false D 0.396,0.448 0.521,0.604 0.125,0.156 10 false E 0.979,1.927 1.104,2.083 0.125,0.156 10 false F 3.146,2.188 3.271,2.344 0.125,0.156 10 false E 2.083,2.042 2.208,2.198 0.125,0.156 10 false F 3.26,1.344 3.385,1.5 0.125,0.156 10 false F 0.75,2.417 0.875,2.573 0.125,0.156 10 true E

Disconnect the connector (labeled D).


d.

Remove the 3 bolts (labeled E), 3 harness clamps (labeled F) and sensor wire.


Hide 89543 5.REMOVE FRONT SPEED SENSOR LH

C155492E01
2.999,2.188 3.141,2.344 0.142,0.156 10 A 2.859,2.009 3.001,2.165 0.142,0.156 10 B 0.399,2.425 0.541,2.581 0.142,0.156 10 C 0.498,1.06 0.640,1.215 0.142,0.156 10 D

a.

Remove the hexagon socket head cap bolt (labeled A) and speed sensor (labeled B) from the knuckle.


Hide 88266B 6.REMOVE FRONT SKID CONTROL SENSOR CLAMP LH

a.

Remove the bolt (labeled C) and skid control sensor clamp (labeled D) from the knuckle.


Hide 89516 7.REMOVE FRONT SKID CONTROL SENSOR WIRE RH

a.
C154444E01
1.181,3.991 1.304,4.151 0.123,0.161 10 A 2.089,3.242 2.212,3.402 0.123,0.161 10 B 2.617,3.098 2.741,3.258 0.123,0.161 10 B 2.004,3.481 2.128,3.642 0.123,0.161 10 B 3.294,2.473 3.417,2.633 0.123,0.161 10 C

Disconnect the connector (labeled A) from the front speed sensor.


b.

Detach the 3 clips (labeled B) and remove the clamp bolt (labeled C).


c.
C154446E05
2.042,0.021 2.167,0.177 0.125,0.156 10 false D 2.927,2.479 3.052,2.635 0.125,0.156 10 false E 2.677,0 2.802,0.156 0.125,0.156 10 false E 3.302,1.542 3.406,1.698 0.104,0.156 10 false F 2.104,1.958 2.229,2.115 0.125,0.156 10 true F 0.042,0.854 0.167,1.01 0.125,0.156 10 true G 0.396,0.448 0.521,0.604 0.125,0.156 10 false H

Disconnect the connector (labeled D).


d.

Remove the connector (labeled D) from the skid control sensor clamp (labeled H).


e.

Remove the 2 bolts (labeled E) and 2 harness clamps (labeled F).


f.

Remove the bolt (labeled G) and skid control sensor clamp (labeled H).


Hide 89542 8.REMOVE FRONT SPEED SENSOR RH

a.
C155493E01
0.124,2.378 0.266,2.541 0.142,0.163 10 A 0.275,2.175 0.417,2.338 0.142,0.163 10 B 3.148,2.626 3.290,2.789 0.142,0.163 10 C 3.109,1.087 3.251,1.250 0.142,0.163 10 D

Remove the hexagon socket head cap bolt (labeled A) and speed sensor (labeled B) from the knuckle.


Hide 88266C 9.REMOVE FRONT SKID CONTROL SENSOR CLAMP RH

a.

Remove the bolt (labeled C) and skid control sensor clamp (labeled D) from the knuckle.