Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › TRAILER BRAKE CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234409 TRAILER BRAKE CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  TRAILER BRAKE CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Chassis / Trailer Brake Controller / Data List.


e.

According to the display on the Techstream, read the Data List.

Trailer Brake Controller:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Slider Switch Position Sensor #1 Slider switch position sensor #1 / min.: 0%, max.: 100% Actual manual trailer brake output slider position -
Slider Switch Position Sensor #2 Slider switch position sensor #2 / min.: 0%, max.: 100% Actual manual trailer brake output slider position -
Gain Rocker Switch (+) GAIN (+) selection button / ON or OFF ON: GAIN (+) selection button ON
OFF: GAIN (+) selection button OFF
-
Gain Rocker Switch (-) GAIN (-) selection button / ON or OFF ON: GAIN (-) selection button ON
OFF: GAIN (-) selection button OFF
-
Type Push Button Switch Trailer brake TYPE selection button / ON or OFF ON: Trailer brake TYPE selection button ON
OFF: Trailer brake TYPE selection button OFF
-
Shift Position Shift Position information / D, R, Fail, Undetermined Actual shift Position -
Brake Fluid Pressure Brake fluid pressure value / min.: 0.000 Mpa max.: 786.420 Mpa - -
TBC Output Voltage TBC output voltage / min.: 0.000 V, max.: 18.000 V - -
Command Value Trailer Brake Output Command value trailer brake output / min.: 0.000%, max.: 100.000% - -
Trailer Brake Light Trailer brake light / ON or OFF ON: Trailer brake light ON
OFF: Trailer brake light OFF
-
Battery Voltage Battery voltage / min.: 0.000 V, max.: 18.000 V 11 to 14 V -
Terminal Temperature Terminal temperature / min.: -30.000°C, max.: 100.000°C Actual terminal temperature -
Manual Gain Manual gain value / min.: 0.0, max.: 10.0 Gain value set when GAIN (+/-) selection button is operated -
Trailer Brake Type Trailer brake type / Electric or Electric + Hydraulic Electric: Trailer brake type set to "Electric" by trailer brake TYPE selection button operation
Electric + Hydraulic: Trailer brake type set to "Electric + Hydraulic" by trailer brake TYPE selection button operation
-
DTC 1 DTC 1 / C14A0, C14A1, C14A2, C14A3, C14A4, C14A5, C14A6, C14A7, U0101, U0129, U0155, - First DTC stored after clearing the DTCs When DTC is not stored, "-" is displayed
DTC1 ODO DTC1 ODO / min.: 0.0000 km, max.: 1609343.0000 km Driving distance when first DTC is stored after clearing the DTCs When DTC is not stored, "-" is displayed
DTC 2 DTC 2/ C14A0, C14A1, C14A2, C14A3, C14A4, C14A5, C14A6, C14A7, U0101, U0129, U0155, - Second DTC stored after clearing the DTCs When DTC is not stored, "-" is displayed
DTC2 ODO DTC2 ODO / min.: 0.0000 km, max.: 1609343.0000 km Driving distance when second DTC is stored after clearing the DTCs When DTC is not stored, "-" is displayed
DTC 3 DTC 3 / C14A0, C14A1, C14A2, C14A3, C14A4, C14A5, C14A6, C14A7, U0101, U0129, U0155, - Third DTC stored after clearing the DTCs When DTC is not stored, "-" is displayed
DTC3 ODO DTC3 ODO / min.: 0.0000 km, max.: 1609343.0000 km Driving distance when third DTC is stored after clearing the DTCs When DTC is not stored, "-" is displayed
DTC 4 DTC 4/ C14A0, C14A1, C14A2, C14A3, C14A4, C14A5, C14A6, C14A7, U0101, U0129, U0155, - Fourth DTC stored after clearing the DTCs When DTC is not stored, "-" is displayed
DTC4 ODO DTC4 ODO / min.: 0.0000 km, max.: 1609343.0000 km Driving distance when fourth DTC is stored after clearing the DTCs When DTC is not stored, "-" is displayed
DTC 5 DTC 5/ C14A0, C14A1, C14A2, C14A3, C14A4, C14A5, C14A6, C14A7, U0101, U0129, U0155, - Fifth DTC stored after clearing the DTCs When DTC is not stored, "-" is displayed
DTC5 ODO DTC5 ODO / min.: 0.0000 km, max.: 1609343.0000 km Driving distance when fifth DTC is stored after clearing the DTCs When DTC is not stored, "-" is displayed



PERFORM ACTIVE TEST


a.

Connect the trailer brake connector to the trailer socket.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Chassis / Trailer Brake Controller / Active Test.

HINT:

The ignition switch must be turned ON to proceed to the Active Test using the Techstream.


Trailer Brake Controller:
Tester Display Test Part Control Range Diagnostic Note
Trailer Brake Output Trailer brake output 0 to 100% Can be operated in the following conditions
·

DTC C14A4 not output

·

Vehicle speed = 0 km/h (0 mph)