Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM27M0U _58 Vehicle Interior _049154 AIR CONDITIONING _0234411 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1443/43  Air Outlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 damper servo sub-assembly (air outlet servo motor) sends pulse signals to inform the air conditioning amplifier of the damper position. The air conditioning amplifier activates the motor (normal, reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet switching.

HINT:

Confirm that no mechanical problem is present because this diagnostic trouble code can be output when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1443/43 Air outlet damper position sensor value does not change even if air conditioning amplifier operates No. 1 damper servo sub-assembly (air outlet servo motor)
·

No. 1 damper servo sub-assembly (air outlet servo motor)

·

Air conditioning harness

·

Air conditioning amplifier



WIRING DIAGRAM

E147168E11
5.271,1 5.75,1.208 0.479,0.208 10 false B BUS 5.271,1.615 5.677,1.813 0.406,0.198 10 false BUS 5.281,2.271 5.792,2.479 0.51,0.208 10 false BUS G 5.01,0.896 5.188,1.042 0.177,0.146 10 false 4 5.01,1.521 5.188,1.667 0.177,0.146 10 false 3 5.01,2.167 5.188,2.313 0.177,0.146 10 false 2 0.344,3.073 2.531,3.469 2.188,0.396 10 false No. 1 Damper Servo Sub-assembly (Air Outlet Servo Motor) 3.146,3.083 4.729,3.281 1.583,0.198 10 false Air Conditioning Harness 5.177,2.958 5.469,3.146 0.292,0.188 10 false z1 5.177,3.115 6.844,3.313 1.667,0.198 10 false Air Conditioning Amplifier

PROCEDURE

1.READ VALUE USING TECHSTREAM (AIR OUTLET SERVO MOTOR TARGET PULSE)
a.

Use the Data List to check if the servo motor is functioning properly.

Air Conditioner
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Air Outlet Servo Pulse (D) No. 1 damper servo sub-assembly (air outlet servo motor) target pulse /
Min.: 0, Max.: 255
FACE: 9 (pulse)
MID: 25 (pulse)
B/L: 32 (pulse)
MID: 39 (pulse)
FOOT: 56 (pulse)
MID: 77 (pulse)
FOOT/DEF: 83 (pulse)
MID: 91 (pulse)
DEF: 97 (pulse)
-

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
OK (Checking from the DTC) A
OK (Checking from the PROBLEM SYMPTOMS TABLE) B
NG C



A

2.REPLACE NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET SERVO MOTOR)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER

2.REPLACE NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET SERVO MOTOR)
a.

Temporarily replace the No. 1 damper servo sub-assembly (air outlet servo motor) with a new one (see page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new one and check that the condition returns to normal.




NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

OK

END (NO. 1 DAMPER SERVO SUB-ASSEMBLY [AIR OUTLET SERVO MOTOR] IS DEFECTIVE)

NG

4.REPLACE AIR CONDITIONING HARNESS
4.REPLACE AIR CONDITIONING HARNESS
a.

Replace the air conditioning harness.



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

OK

END (AIR CONDITIONING HARNESS IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER