Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM27M0U _58 Vehicle Interior _049154 AIR CONDITIONING _0234411 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1497/97  BUS IC Communication Malfunction  


DESCRIPTION

The air conditioning harness connects the air conditioning amplifier and each servo motor. The air conditioning amplifier supplies power and sends operation instructions to each servo motor through the air conditioning harness. Each servo motor sends the damper position information to the air conditioning amplifier.

DTC Code DTC Detection Condition Trouble Area
B1497/97 Communication line error or open
·

Air conditioning harness

·

No. 1 damper servo sub-assembly (air mix servo motor)

·

No. 1 damper servo sub-assembly (air outlet servo motor)

·

Air inlet servo motor

·

Air conditioning amplifier

·

Harness or connector



WIRING DIAGRAM

E282762E01
1.671,4.205 1.790,4.407 0.119,0.202 10 B 1.922,4.212 2.165,4.389 0.243,0.177 10 J19 1.96,1.529 2.137,1.706 0.177,0.177 10 z1 1.96,1.137 2.137,1.313 0.177,0.177 10 z1 1.96,0.73 2.137,0.907 0.177,0.177 10 z1 1.298,1.529 1.815,1.731 0.517,0.202 10 BUS G 1.456,1.137 1.816,1.339 0.360,0.202 10 BUS 1.326,0.73 1.815,0.933 0.489,0.202 10 B BUS 2,1.349 2.130,1.520 0.130,0.171 10 2 2,0.957 2.130,1.128 0.130,0.171 10 3 2,0.551 2.130,0.722 0.130,0.171 10 4 1.958,4.036 2.130,4.190 0.173,0.154 10 21 2.562,6.037 2.858,6.192 0.297,0.155 10 A/C 1.13,5.89 1.944,6.095 0.814,0.205 10 from Battery 0.434,5.128 2.039,5.332 1.605,0.205 10 Air Conditioning Amplifier 3.739,5.842 5.321,6.042 1.581,0.200 10 Air Conditioning Harness 5.385,5.46 6.723,5.660 1.338,0.200 10 Air Inlet Servo Motor 4.853,3.61 7.079,3.956 2.226,0.346 10 No. 1 Damper Servo Sub-assembly (Air Outlet Servo Motor) 4.874,1.803 7.132,2.302 2.258,0.498 10 No. 1 Damper Servo Sub-assembly (Air Mix Servo Motor)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Select the Active Test, using the Techstream to generate a control command, and then check that the servo motor operates.

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Air Mix Servo Targ Pulse (D) No. 1 damper servo sub-assembly (air mix servo motor) pulse Min.: 5, Max.: 104 -
Air Outlet Servo Pulse (D) No. 1 damper servo sub-assembly (air outlet servo motor) pulse Min.: 9, Max.: 97 -
Air Inlet Damper Targ Pulse Air inlet damper target pulse Min.: 7, Max.: 28 -


OK:

Arm of the servo motor selected in the Active Test moves smoothly


Result
Result Proceed to
One of the servo motors is malfunctioning A
All of the servo motor are malfunctioning B


A

2.SYSTEM CHECK

B

6.CHECK AIR CONDITIONING HARNESS
2.SYSTEM CHECK
a.

According to the test, proceed to the next step.

Result
Result Proceed to
Only the No. 1 damper servo sub-assembly (air mix servo motor) is malfunctioning A
Only the No. 1 damper servo sub-assembly (air outlet servo motor) is malfunctioning B
Only the air inlet control servo motor is malfunctioning C



A

3.CHECK NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR MIX SERVO MOTOR)

B

4.CHECK NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET SERVO MOTOR)

C

5.CHECK AIR INLET SERVO MOTOR
3.CHECK NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR MIX SERVO MOTOR)
a.

Replace the No. 1 damper servo sub-assembly (air mix servo motor) (See page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.



b.

Check for DTC (See page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1497/97 is not output A
DTC B1497/97 is output B



A

END (NO. 1 DAMPER SERVO SUB-ASSEMBLY [AIR MIX SERVO MOTOR] IS DEFECTIVE)

B

6.CHECK AIR CONDITIONING HARNESS
4.CHECK NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET SERVO MOTOR)
a.

Replace the No. 1 damper servo sub-assembly (air outlet servo motor) (See page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.



b.

Check for DTC (See page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1497/97 is not output A
DTC B1497/97 is output B



A

END (NO. 1 DAMPER SERVO SUB-ASSEMBLY [AIR OUTLET SERVO MOTOR] IS DEFECTIVE)

B

6.CHECK AIR CONDITIONING HARNESS
5.CHECK AIR INLET SERVO MOTOR
a.

Replace the air inlet servo motor (See page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.



b.

Check for DTC (See page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1497/97 is not output A
DTC B1497/97 is output B



A

END (AIR INLET SERVO MOTOR IS DEFECTIVE)

B

6.CHECK AIR CONDITIONING HARNESS
6.CHECK AIR CONDITIONING HARNESS
a.

Replace the air conditioning harness.

HINT:

Since the air conditioning harness cannot be inspected while it is removed from the vehicle, replace the air conditioning harness with a new or a known good one and check that the condition returns to normal.



b.

Check for DTC (See page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1497/97 is not output A
DTC B1497/97 is output B



A

END (AIR CONDITIONING HARNESS IS DEFECTIVE)

B

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
7.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
U152810E02
2.5,2.531 2.573,2.865 false 0.156,0.354 2.406,0.771 2.25,0.417 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier) 2.552,2.906 2.708,3.063 0.156,0.156 10 false B 0.823,2.375 1.115,2.583 0.292,0.208 10 false J19

Disconnect the J19 air conditioning amplifier connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
J19-21 (B) - Body ground Always 11 to 14 V




OK

REPLACE AIR CONDITIONING AMPLIFIER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR