When the air conditioning amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the air conditioning amplifier. Then, the magnetic clutch relay (MG CLT) turns on to operate the magnetic clutch.
Use the Data List to check if the air conditioning signal is functioning properly.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| A/C Signal | A/C switch signal /
ON or OFF |
ON: A/C switch ON
OFF: A/C switch OFF |
- |
The display is as specified in the normal condition.
OK
NG
Remove the A/C IG fuse from the main body ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A/C IG fuse | Always | Below 1 Ω |
OK
NG
Remove the magnetic clutch relay (MG CLT) from the engine room relay block, junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Engine room relay block, junction block magnetic clutch relay terminal 5 - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| Engine room relay block, junction block magnetic clutch relay terminal 1 - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
OK
NG
Remove the magnetic clutch relay from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | When battery voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
OK
NG
Disconnect the J19 air conditioning amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J19-20 (MGC) - Body ground | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 11 to 14 V |
OK
NG
Reconnect the J19 air conditioning amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J19-20 (MGC) - Body ground | Engine is running
Blower switch LO A/C switch ON |
Below 1 V |
| Engine is running
Blower switch LO A/C switch OFF |
11 to 14 V |
OK
NG
Disconnect the D60 air conditioning compressor connector.
Disconnect the magnetic clutch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (MG+) - 1 | Always | Below 1 Ω |
| 3 (MG+) or 1 - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - Body ground | Always | 3.4 to 3.8 Ω |
When connector terminal 1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound can be heard, and 2) the magnetic clutch's hub and rotor lock.
OK
NG
Disconnect the D60 air conditioning compressor connector.
Remove the magnetic clutch relay (MG CLT) from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D60-3 (MG+) - Engine room relay block, junction block magnetic clutch relay terminal 3 | Always | Below 1 Ω |
| D60-3 (MG+) or Engine room relay block, junction block magnetic clutch relay terminal 3 - Body ground | Always | 10 kΩ or higher |
OK
NG