Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM27M0U _58 Vehicle Interior _049154 AIR CONDITIONING _0234412 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1413/13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor is installed on the evaporator in the air conditioner unit to detect the cooled air temperature that has passed through the evaporator and control the air conditioning. It sends appropriate signals to the air conditioning amplifier. The resistance of the No. 1 cooler thermistor changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This sensor is used for frost prevention.

DTC Code DTC Detection Condition Trouble Area
B1413/13 Open or short in evaporator temperature sensor circuit
·

No. 1 cooler thermistor

·

Air conditioning harness

·

Air conditioning amplifier



WIRING DIAGRAM

E147578E09
1.041,1.263 2.781,1.592 1.739,0.330 10 No. 1 Cooler Thermistor 5.385,2.37 5.613,2.529 0.229,0.160 10 z1 5.385,2.539 7.020,2.708 1.635,0.170 10 Air Conditioning Amplifier 3.676,2.539 5.283,2.708 1.607,0.170 10 Air Conditioning Harness 5.487,0.944 5.830,1.148 0.343,0.205 10 TEA 5.487,1.772 5.830,1.976 0.343,0.205 10 SGA 5.288,0.845 5.441,0.998 0.152,0.152 10 6 5.288,1.674 5.441,1.826 0.152,0.152 10 5

PROCEDURE

1.READ VALUE USING TECHSTREAM (EVAPORATOR FIN THERMISTOR)
a.

Use the Data List to check if the No. 1 cooler thermistor is functioning properly.

Air Conditioner
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor No. 1 cooler thermistor /
Min.: -29.7°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual No. 1 cooler thermistor is displayed Open in circuit: -29.7°C (-21.46°F)
Short in circuit: 59.55°C (139.19°F)

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
NG A
OK (Checking from the PROBLEM SYMPTOMS TABLE) B
OK (Checking from the DTC) C



A

2.INSPECT NO. 1 COOLER THERMISTOR

B

C

REPLACE AIR CONDITIONING AMPLIFIER

2.INSPECT NO. 1 COOLER THERMISTOR
U152754E02
0.917,0.396 1.01,0.396 1.01,0.396 1.135,0.813 false 0.208,1.854 0.323,2.333 false 0.198,0.323 0.938,0.469 0.74,0.146 10 false Evaporator 0.104,2.354 1.688,2.531 1.583,0.177 10 false No. 1 Cooler Thermistor 2.375,2.344 3.958,2.521 1.583,0.177 10 false No. 1 Cooler Thermistor 2.031,1 2.51,1.365 0.479,0.365 10 false Sensor Area 2.604,0.385 4.333,0.74 1.729,0.354 10 false Component without harness connected: 4.542,0.021 5.604,0.24 1.063,0.219 10 false Resistance (kΩ) 5.26,2.458 6.625,2.698 1.365,0.24 10 false Temperature °C (°F)

a.

Remove the No. 1 cooler thermistor connector (see page Vehicle Interior>AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 -10°C (14°F) 7.30 to 9.10 kΩ
-5°C (23°F) 5.65 to 6.95 kΩ
0°C (32°F) 4.40 to 5.35 kΩ
5°C (41°F) 3.40 to 4.15 kΩ
10°C (50°F) 2.70 to 3.25 kΩ
15°C (59°F) 2.14 to 2.58 kΩ
20°C (68°F) 1.71 to 2.05 kΩ
25°C (77°F) 1.38 to 1.64 kΩ
30°C (86°F) 1.11 to 1.32 kΩ


NOTICE:
·

Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).




OK

3.REPAIR OR REPLACE AIR CONDITIONING HARNESS

NG

3.REPAIR OR REPLACE AIR CONDITIONING HARNESS
a.

Repair or replace the air conditioning harness.



NEXT

4.CHECK FOR DTC