Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM27M0U _58 Vehicle Interior _049154 AIR CONDITIONING _0234412 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the air conditioning amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the air conditioning amplifier. Then, the magnetic clutch relay (MG CLT) turns on to operate the magnetic clutch.

WIRING DIAGRAM

E146216E05
5.332,2.631 6.964,2.801 1.631,0.170 10 Air Conditioning Amplifier 5.514,1.551 5.896,1.720 0.381,0.170 10 MGC 4.786,3.662 5.167,3.831 0.381,0.170 10 MG+ 2.469,1.911 3.075,2.081 0.606,0.170 10 MG CLT 1.156,3.994 1.705,4.164 0.549,0.170 10 A/C IG 2.576,4.169 3.956,4.339 1.380,0.170 10 from IG1 No.2 Relay 4.967,4.169 6.095,4.339 1.128,0.170 10 Magnetic Clutch 1.914,2.517 3.660,2.687 1.745,0.170 10 Engine Room Relay Block 5.332,2.456 5.644,2.626 0.312,0.170 10 J19 4.473,5.237 6.500,5.407 2.027,0.170 10 Air Conditioning Compressor 4.473,5.062 4.785,5.232 0.312,0.170 10 D60 5.18,1.438 5.416,1.608 0.236,0.170 10 20 3.746,1.539 3.878,1.709 0.132,0.170 10 1 1.691,1.539 1.823,1.709 0.132,0.170 10 1 3.746,1.04 3.878,1.210 0.132,0.170 10 1 3.204,1.427 3.336,1.597 0.132,0.170 10 2 3.204,0.928 3.336,1.097 0.132,0.170 10 3 4.754,3.412 4.886,3.582 0.132,0.170 10 3 4.543,3.849 4.675,4.019 0.132,0.170 10 1 1.691,1.04 1.823,1.210 0.132,0.170 10 1 2.222,1.427 2.354,1.597 0.132,0.170 10 1 2.222,0.928 2.354,1.097 0.132,0.170 10 5

PROCEDURE

1.READ VALUE USING TECHSTREAM (A/C SIGNAL)
a.

Use the Data List to check if the air conditioning signal is functioning properly.

Engine and ECT
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
A/C Signal Air conditioning switch signal /
ON or OFF
ON: Air conditioning ON
OFF: Air conditioning OFF
-

OK:

The display is as specified in the normal condition.




OK

NG

2.INSPECT FUSE (A/C IG)
2.INSPECT FUSE (A/C IG)
a.

Remove the A/C IG fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A/C IG fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK, JUNCTION BLOCK - BATTERY)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK, JUNCTION BLOCK - BATTERY)
E280657E02
1.24,2.76 1.24,3.01 false 0.125,0.021 2.802,0.396 2.677,0.375 10 false Component without relay connected: (Engine Room Relay Block, Junction Block) 0.177,3.052 2.281,3.26 2.104,0.208 10 false Magnetic Clutch Relay (MG CLT)

a.

Remove the magnetic clutch relay (MG CLT) from the engine room relay block, junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Engine room relay block magnetic clutch relay terminal 5 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
Engine room relay block magnetic clutch relay terminal 1 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

4.INSPECT MAGNETIC CLUTCH RELAY (MG CLT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAGNETIC CLUTCH RELAY (MG CLT)
A378301E02
1.698,0.448 1.99,0.729 false 2.635,0.708 2.906,0.438 false 2.51,1.125 2.896,0.99 false 2.51,1.615 2.896,1.677 false 0.219,0.771 0.375,0.969 0.156,0.198 10 false 3 1.198,0.771 1.354,0.969 0.156,0.198 10 false 5 0.24,1.313 0.396,1.51 0.156,0.198 10 false 2 1.208,1.302 1.365,1.5 0.156,0.198 10 false 1 1.573,0.313 1.729,0.51 0.156,0.198 10 false 1 2.948,0.313 3.104,0.51 0.156,0.198 10 false 2 2.969,0.927 3.125,1.125 0.156,0.198 10 false 5 2.948,1.604 3.104,1.802 0.156,0.198 10 false 3

a.

Remove the magnetic clutch relay from the engine room relay block, junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 5 When battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
When battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

REPLACE MAGNETIC CLUTCH RELAY

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
U152750E02
1.344,2.448 1,2.906 false 0.479,0.385 2.74,0.771 2.26,0.385 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier) 0.708,2.427 0.99,2.646 0.281,0.219 10 false J19 0.792,2.948 1.198,3.125 0.406,0.177 10 false MGC

a.

Disconnect the J19 air conditioning amplifier connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J19-20 (MGC) - Body ground Ignition switch OFF Below 1 V
Ignition switch ON 11 to 14 V




OK

6.CHECK AIR CONDITIONING AMPLIFIER (MGC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK AIR CONDITIONING AMPLIFIER (MGC VOLTAGE)
U152745E02
1.365,2.104 1.031,2.688 false 0.333,0.323 2.604,0.688 2.271,0.365 10 false Component with harness connected: (Air Conditioning Amplifier) 1.771,1.438 2.031,1.625 0.26,0.188 10 false J19 0.833,2.719 1.229,2.896 0.396,0.177 10 false MGC

a.

Reconnect the J19 air conditioning amplifier connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J19-20 (MGC) - Body ground Engine is running
Blower switch LO
A/C switch ON
Below 1 V
Engine is running
Blower switch LO
A/C switch OFF
11 to 14 V




OK

7.INSPECT AIR CONDITIONING COMPRESSOR (COMPRESSOR HARNESS)

NG

REPLACE AIR CONDITIONING AMPLIFIER

7.INSPECT AIR CONDITIONING COMPRESSOR (COMPRESSOR HARNESS)
E146414E01
0.158,0.121 2.640,0.430 2.482,0.309 10 Component without harness connected: (Air Conditioning Compressor) 0.158,2.674 2.633,2.982 2.475,0.309 10 Component without harness connected: (Magnetic Clutch) 1.722,1.738 2.377,2.065 false 2.395,1.99 2.753,2.174 0.357,0.184 10 MG+

a.

Disconnect the D60 air conditioning compressor connector.


b.

Disconnect the magnetic clutch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 (MG+) - 1 Always Below 1 Ω
3 (MG+) or 1 - Body ground Always 10 kΩ or higher




OK

8.INSPECT MAGNETIC CLUTCH

NG

REPAIR AIR CONDITIONING COMPRESSOR

8.INSPECT MAGNETIC CLUTCH
a.
E146516E01
0.223,0.397 2.775,0.747 2.552,0.350 10 Component without harness connected: (Magnetic Clutch)

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - Body ground Always 3.4 to 3.8 Ω



b.

When connector terminal 1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound can be heard, and 2) the magnetic clutch's hub and rotor lock.



OK

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING COMPRESSOR - ENGINE ROOM RELAY BLOCK, JUNCTION BLOCK)

NG

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING COMPRESSOR - ENGINE ROOM RELAY BLOCK, JUNCTION BLOCK)
U152848E01
0.523,0.064 2.887,0.434 2.364,0.371 10 Front view of wire harness connector: (to Air Conditioning Compressor) 0.918,1.526 1.195,1.747 0.278,0.222 10 D60 4.263,0.057 7.102,0.446 2.839,0.390 10 Component without relay connected: (Engine Room Relay Block, Junction Block) 1.865,2.159 3.965,2.364 2.100,0.204 10 Magnetic Clutch Relay (MG CLT) 4.7,2.348 3.992,2.239 false 1.664,1.748 1.395,1.989 false 1.054,1.975 1.405,2.131 0.350,0.156 10 MG+

a.

Disconnect the D60 air conditioning compressor connector.


b.

Remove the magnetic clutch relay (MG CLT) from the engine room relay block, junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D60-3 (MG+) - Engine room relay block magnetic clutch relay terminal 3 Always Below 1 Ω
D60-3 (MG+) or Engine room relay block magnetic clutch relay terminal 3 - Body ground Always 10 kΩ or higher




OK

REPLACE AIR CONDITIONING AMPLIFIER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR