Home › Vehicle Interior › THEFT DETERRENT › THEFT DETERRENT SYSTEM
RM27M0U _58 Vehicle Interior _049155 THEFT DETERRENT _0234426 THEFT DETERRENT SYSTEM J

THEFT DETERRENT  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is built into the hood lock. This switch turns on when the engine hood is opened and turns off when the engine hood is closed.


WIRING DIAGRAM

B160791E02
4.625,1.177 5.052,1.354 0.427,0.177 10 false HCTY 5.01,1.927 5.271,2.104 0.26,0.177 10 false J4 1.823,1.51 2.177,1.677 0.354,0.167 10 false A29 4.344,1.063 4.51,1.24 0.167,0.177 10 false 16 1.979,1.083 2.094,1.24 0.115,0.156 10 false 2 2.781,1.083 2.896,1.24 0.115,0.156 10 false 1 1.813,1.656 3.417,2.188 1.604,0.531 10 false Hood Lock Assembly (Engine Hood Courtesy Switch) 5,2.094 6.073,2.323 1.073,0.229 10 false Main Body ECU

PROCEDURE

1.READ VALUE USING TECHSTREAM (ENGINE HOOD COURTESY SWITCH)
a.

Using the Techstream, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Hood Courtesy Switch Engine hood courtesy switch /
ON or OFF
ON: Engine hood is open
OFF: Engine hood is closed
-

OK:

ON (engine hood is open) appears on screen.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
B165961E01
0.606,2.243 1.735,2.424 1.129,0.181 10 UNLOCK Position 3.203,2.243 4.131,2.424 0.928,0.181 10 LOCK Position 4.548,0.076 7.012,0.424 2.465,0.348 10 Component without harness connected: (Hood Lock Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 UNLOCK position Below 1 Ω
LOCK position 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE HOOD COURTESY SWITCH AND BODY GROUND)

NG

REPLACE HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE HOOD COURTESY SWITCH AND BODY GROUND)
a.

Disconnect the J4 main body ECU connector.

B443056E02
4.427,1.583 4.781,1.802 0.354,0.219 0.781,1.552 1.135,1.771 0.354,0.219 2.563,1.792 2.979,2.229 false 0.844,0.115 3.188,0.552 2.344,0.438 10 false Front view of wire harness connector: (to Main Body ECU) 4.219,0.104 6.563,0.542 2.344,0.438 10 false Front view of wire harness connector: (to Engine Hood Courtesy Switch) 3.042,2.188 3.563,2.385 0.521,0.198 10 false HCTY 0.875,1.573 1.146,1.771 0.271,0.198 10 false J4 4.479,1.604 4.75,1.802 0.271,0.198 10 false A29


b.

Disconnect the A29 engine hood courtesy switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J4-16 (HCTY) - A29-1 Always Below 1 Ω
A29-2 - Body ground
J4-16 (HCTY) or A29-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR