Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM27M0U _58 Vehicle Interior _049156 ENGINE IMMOBILISER _0234432 ENGINE IMMOBILISER SYSTEM U

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK TRANSPONDER KEY AMPLIFIER


U151953E02
3.438,0.292 3.75,0.5 0.313,0.208 10 false J20

a.

Disconnect the J20 amplifier connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
J20-7 (AGND) - Body ground GR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J20 amplifier connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
J20-1 (VC5) - J20-7 (AGND) G - GR Power supply No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder 4.6 to 5.4 V
J20-4 (CODE) - J20-7 (AGND) LG - GR Demodulated signal of key code data No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (see waveform 1)
J20-5 (TXCT) - J20-7 (AGND) L - GR Key code output signal No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (see waveform 2)
J20-7 (AGND) - Body ground GR - Body ground Ground Always Below 1 Ω

If the result is not as specified, the amplifier may have a malfunction.


e.
B443023E01
0.063,0.042 0.854,0.24 0.792,0.198 10 false Waveform 1: 0.323,1.01 0.635,1.198 0.313,0.188 10 false GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference):
Terminal No. (Symbols) Tool Setting Condition
J20-4 (CODE) - J20-7 (AGND) 5 V/DIV., 20 msec./DIV. Key inserted in ignition key cylinder


f.
B443024E01
0.323,1.073 0.781,1.271 0.458,0.198 10 false GND 0.083,0.063 0.865,0.24 0.781,0.177 10 false Waveform 2:

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference):
Terminal No. (Symbols) Tool Setting Condition
J20-5 (TXCT) - J20-7 (AGND) 5 V/DIV., 20 msec./DIV. Key inserted in ignition key cylinder



CHECK TRANSPONDER KEY ECU


B443025E01
3.313,0.219 3.677,0.448 0.365,0.229 3.385,0.25 3.844,0.448 0.458,0.198 10 false J26

a.

Disconnect the J26 ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
J26-16 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J26-1 (+B) - J26-16 (GND) G - W-B Battery Always 11 to 14 V
J26-2 (IG) - J26-16 (GND) GR - W-B Ignition switch Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
J26-3 (KSW) - J26-16 (GND) LG - W-B Unlock warning switch No key in ignition key cylinder 10 kΩ or higher
Key inserted in ignition key cylinder Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J26 ECU connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
J26-14 (VC5) - J26-16 (GND) G - W-B Power source No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder 4.6 to 5.4 V
J26-7 (CTY) - J26-16 (GND) Y - W-B Door courtesy Door closed 10 kΩ or higher
Door open Below 1 Ω
J26-4 (TXCT) - J26-16 (GND) L - W-B Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (see waveform 1)
J26-15 (CODE) - J26-16 (GND) LG - W-B Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (see waveform 2)
J26-13 (EFIO) - J26-16 (GND) Y - W-B ECM output signal Ignition switch off Below 1 V
Ignition switch ON Pulse generation (see waveform 3)
J26-12 (EFII) - J26-16 (GND) SB - W-B ECM input signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected Pulse generation (see waveform 4)
J26-8 (IND) - J26-16 (GND) V - W-B Security indicator light signal Immobiliser set status Alternating between 11 to 14 V and below 1 V
Immobiliser unset status Below 1 V
J26-9 (D) - J26-16 (GND) BE - W-B Diagnosis tester communication Always Pulse generation

If the result is not as specified, the ECU may have a malfunction.


e.
B443024E02
0.073,0.052 0.896,0.24 0.823,0.188 10 false Waveform 1: 0.313,1.073 0.771,1.271 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference):
Terminal No. (Symbols) Tool Setting Condition
J26-4 (TXCT) - J26-16 (GND) 5 V/DIV., 20 msec./DIV. Key inserted in ignition key cylinder


f.
B443023E02
0.063,0.042 0.854,0.24 0.792,0.198 10 false Waveform 2: 0.323,1.01 0.635,1.198 0.313,0.188 10 false GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference):
Terminal No. (Symbols) Tool Setting Condition
J26-15 (CODE) - J26-16 (GND) 5 V/DIV., 20 msec./DIV. Key inserted in ignition key cylinder


g.
B443040E01
0.094,0.052 0.885,0.26 0.792,0.208 10 false Waveform 3: 0.323,1.125 0.781,1.323 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference):
Terminal No. (Symbols) Tool Setting Condition
J26-13 (EFIO) - J26-16 (GND) 10 V/DIV., 100 msec./DIV. Ignition switch ON


h.
B229710E28
0.188,0.74 0.521,0.938 0.333,0.198 10 false GND 0.052,0.021 0.813,0.198 0.76,0.177 10 false Waveform 4:

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference):
Terminal No. (Symbols) Tool Setting Condition
J26-12 (EFII) - J26-16 (GND) 5 V/DIV., 500 msec./DIV. Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected