Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM27M0U _58 Vehicle Interior _049156 ENGINE IMMOBILISER _0234432 ENGINE IMMOBILISER SYSTEM J

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the transponder key ECU.

WIRING DIAGRAM

E146075E02
5.341,2.554 5.514,2.757 0.172,0.202 10 16 4.345,1.779 4.633,1.921 0.288,0.142 10 IGN 3.491,1.084 3.779,1.226 0.288,0.142 10 IMB 5.675,2.676 6.026,2.879 0.351,0.202 10 GND 5.665,1.606 5.932,1.809 0.267,0.202 10 IG 5.637,0.911 5.904,1.114 0.267,0.202 10 +B 5.424,1.476 5.545,1.679 0.121,0.202 10 2 5.424,0.821 5.545,1.023 0.121,0.202 10 1 5.407,3.714 5.687,3.885 0.280,0.170 10 J26 0.961,2.647 2.146,3.280 1.185,0.633 10 from IG2 Relay 0.1,2.594 0.981,2.871 0.881,0.278 10 from Battery 5.407,3.877 6.933,4.100 1.526,0.223 10 Transponder Key ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT FUSE (IMB, IGN)
a.

Remove the IMB fuse and IGN fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
IMB fuse Always Below 1 Ω
IGN fuse




OK

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
a.
U151854E02
0.542,1.719 0.854,2.031 false 2.542,2.323 2.844,2.531 false 0.677,1.344 1.052,2.01 false 0.104,0.094 2.365,0.49 2.26,0.396 10 false Front view of wire harness connector: (to Transponder Key ECU) 0.333,1.615 0.563,1.813 0.229,0.198 10 false +B 2.865,2.469 3.25,2.667 0.385,0.198 10 false GND 0.531,1.24 0.76,1.438 0.229,0.198 10 false IG 1.646,1.26 1.906,1.458 0.26,0.198 10 false J26

Disconnect the J26 ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J26-16 (GND) - Body ground Always Below 1 Ω

Standard voltage:
Tester Connection Switch Condition Specified Condition
J26-1 (+B) - Body ground Always 11 to 14 V
J26-2 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR