Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM27M0U _58 Vehicle Interior _049157 METER / GAUGE / DISPLAY _0234436 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the combination meter. This circuit provides 2 power source types: one is a constant power source mainly used as a backup power source, and other is a power source mainly used for signal transmission. The constant power source is mainly used as a backup power source of the meter CPU. However, it is also used for communication. If a voltage of 12 V is not applied to terminal IG+ when the ignition switch ON, the indicator will not operate.

WIRING DIAGRAM

E146026E03
5.817,3.188 6.110,3.389 0.293,0.201 10 J28 6.123,0.634 6.619,0.835 0.496,0.201 10 B 5.847,0.523 6.048,0.724 0.201,0.201 10 1 3.023,0.453 3.546,0.654 0.523,0.201 10 MET-B 4.387,1.476 4.754,1.677 0.367,0.201 10 MET 2.497,1.606 3.509,1.807 1.011,0.201 10 from IG2 Relay 1.105,3.653 2.116,3.854 1.011,0.201 10 Battery 6.123,1.611 6.619,1.812 0.496,0.201 10 IG+ 5.847,1.5 6.048,1.701 0.201,0.201 10 2 6.123,2.545 6.619,2.746 0.496,0.201 10 ES 5.847,2.434 6.048,2.635 0.201,0.201 10 24 5.817,3.392 7.049,3.594 1.233,0.201 10 Combination Meter

PROCEDURE

1.INSPECT FUSE (MET, MET-B)
a.

Remove the MET and MET-B fuses from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MET fuse Always Below 1 Ω
MET-B fuse




OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)
U152712E02
2.115,1.448 2.542,1.667 false 2.594,0.938 2.25,1.365 false 2.688,1.156 2.323,1.354 false 0.083,0.021 2.427,0.406 2.344,0.385 10 false Rear view of wire harness connector: (to Combination Meter) 0.354,1.177 0.604,1.354 0.25,0.177 10 false J28 2.76,1.052 2.906,1.219 0.146,0.167 10 false B 2.615,0.781 2.875,0.969 0.26,0.188 10 false IG+ 2.573,1.604 2.875,1.792 0.302,0.188 10 false ES

a.

Disconnect the J28 meter connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J28-24 (ES) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
J28-1 (B) - Body ground Always 11 to 14 V
J28-2 (IG+) - Body ground Ignition switch ON




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR