Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM27M0U _58 Vehicle Interior _049157 METER / GAUGE / DISPLAY _0234436 METER / GAUGE SYSTEM D

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  OPERATION CHECK  


INSPECT INDICATOR/WARNING LIGHT


a.

Check the following indicators and warning lights.

Indicator/Warning light Switch Condition Specified Condition
ABS warning light Ignition switch OFF → ON Comes on for 3 seconds
SLIP indicator light
SRS warning light Ignition switch OFF → ON Comes on for 6 seconds
CHARGE warning light Ignition switch OFF → ON Illuminates when the ignition switch is turned ON. Turns off when engine is started.
MIL



INSPECT SPEEDOMETER


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on Techstream, read the "Data List".

Reference:
for mph:
Techstream Display (mph) Speedometer Display (mph)
20 19.1 to 21.6
40 39.3 to 42.1
60 59.6 to 62.4
80 79.8 to 83
100 99.9 to 103.3
120 120 to 125.5

for km/h:
Techstream Display (km/h) Speedometer Display (km/h)
20 18.3 to 22.3
40 38.5 to 43
60 58.8 to 63.3
80 78.9 to 83.9
100 99.2 to 104.2
120 119.6 to 124.6
140 139.9 to 144.9
160 160.3 to 165.3
180 180.6 to 185.6
200 201 to 206


NOTICE:

Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.



f.

Check the deflection width of the speedometer indicator.

Reference:

0.5 km/h (0.3 mph)




INSPECT TACHOMETER


a.

Connect a tune-up tachometer, and start the engine.


b.

Compare the test results with the tachometer indicator.

DC 13.5 V, at 25°C (77°F):
Standard indication (rpm) Acceptable range
Data in ( ) is for reference (rpm)
700 630 to 770
1000 (900 to 1100)
2000 (1850 to 2150)
3000 2800 to 3200
4000 (3800 to 4200)
5000 4800 to 5200
6000 (5750 to 6250)
7000 6700 to 7300


If the result is not as specified, the speedometer may have a malfunction.



INSPECT METER/GAUGE


a.

Connect the Techstream to the DLC3.


b.

Perform "Active Test" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

Each meter/gauge's needle indication is normal.




INSPECT WARNING/INDICATOR LIGHT


a.

Connect the Techstream to the DLC3.


b.

Perform "Active Test" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

Each warning/indicator light turns ON and OFF using the Techstream.




INSPECT MULTI-INFORMATION DISPLAY


a.

Connect the Techstream to the DLC3.


b.

Perform "Active Test" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display area's background may turn white. If this occurs, end this Active Test and turn the ignition switch off.


OK:

All dots in the multi-information display turn ON and OFF using the Techstream.