Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049158 NAVIGATION / MULTI INFO DISPLAY _0234440 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E280105E08
5.625,0.76 6.083,0.958 0.458,0.198 10 false REV 5.427,0.656 5.885,0.854 0.458,0.198 10 false 2 5.51,1.354 5.969,1.552 0.458,0.198 10 false J135 5.531,1.521 6.729,2.135 1.198,0.615 10 false Navigation Receiver Assembly 4.208,0.646 4.667,0.844 0.458,0.198 10 false 1 3.927,0.635 4.385,0.833 0.458,0.198 10 false RL 3,1.104 3.458,1.302 0.458,0.198 10 false D35 3.01,1.271 4.385,1.99 1.375,0.719 10 false Park/Neutral Posistion Switch Assembly 0.313,0.771 1.656,0.979 1.344,0.208 10 false from BK/UP LP Fuse 3.115,0.667 3.573,0.865 0.458,0.198 10 false 2 3.313,0.635 3.771,0.833 0.458,0.198 10 false RB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E278094

Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK)].


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK NAVIGATION RECEIVER ASSEMBLY
2.CHECK NAVIGATION RECEIVER ASSEMBLY
U152702E01
0.067,0.058 0.309,0.243 0.242,0.186 10 *a 1.529,0.502 1.894,0.692 0.364,0.191 10 J135 0.063,0.733 0.392,0.904 0.330,0.171 10 REV 0.944,1.363 0.643,0.82 0.643,0.82 0.459,0.82 false

a.

Disconnect the navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J135-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
J135-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the J135 navigation receiver assembly connector.


b.

Disconnect the D35 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J135-2 (REV) - D35-1 (RL) Always Below 1 Ω
J135-2 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U152818E02
1.792,1.031 2.01,0.365 2.01,0.365 2.229,0.365 true 2.281,0.271 2.573,0.479 0.292,0.208 10 false RB 0.313,1.042 0.604,1.25 0.292,0.208 10 false D35 0.042,0 0.333,0.208 0.292,0.208 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D35-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/neutral Position Switch Assembly)

HINT:

If replacing the park/neutral position switch assembly, refer to the procedures below.





OK

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR