Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049158 NAVIGATION / MULTI INFO DISPLAY _0234440 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

This circuit sends a microphone signal from the telephone microphone assembly to the navigation receiver assembly.

It also supplies power from the navigation receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM

E280091E18
0.469,2.688 2.271,3.063 1.802,0.375 10 false Roof Console Box Assembly 0.792,0.604 1.573,1.698 0.781,1.094 10 false Telephone Microphone Assembly 1.865,0.854 2.229,1.01 0.365,0.156 10 false MI1+ 1.885,1.25 2.229,1.406 0.344,0.156 10 false MIC- 1.865,0.458 2.313,0.615 0.448,0.156 10 false ACC 4.323,1.865 4.938,2.021 0.615,0.156 10 false Shielded 3.156,1.875 3.771,2.031 0.615,0.156 10 false Shielded 2.313,2.052 2.563,2.208 0.25,0.156 10 false 14 2.313,0.885 2.521,1.042 0.208,0.156 10 false 9 2.313,1.271 2.521,1.427 0.208,0.156 10 false 8 2.313,0.469 2.563,0.625 0.25,0.156 10 false 10 5.469,2.063 5.594,2.219 0.125,0.156 10 false 6 5.396,1.656 5.583,1.813 0.188,0.156 10 false 18 5.469,0.875 5.583,1.031 0.115,0.156 10 false 5 5.396,1.271 5.583,1.427 0.188,0.156 10 false 19 5.469,0.469 5.594,0.625 0.125,0.156 10 false 4 5.469,2.677 6.833,3.323 1.365,0.646 10 false Navigation Receiver Assembly 0.469,2.531 0.948,2.74 0.479,0.208 10 false W7 5.469,2.521 5.896,2.698 0.427,0.177 10 false J135 5.708,0.948 6.146,1.104 0.438,0.156 10 false MIN+ 5.708,1.344 6.146,1.5 0.438,0.156 10 false MIN- 5.708,1.729 6.198,1.885 0.49,0.156 10 false SGND 5.708,0.521 6.146,0.677 0.438,0.156 10 false MACC 1.802,2.042 2.333,2.198 0.531,0.156 10 false SGND 5.708,2.115 6.146,2.271 0.438,0.156 10 false SNS2

PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
U152834E02
2.052,1.333 2.167,1.927 2.167,1.927 2.396,1.927 true 2.177,1.333 2.406,1.698 2.406,1.698 2.635,1.698 true 2.167,1.094 2.49,0.406 2.49,0.406 2.719,0.406 true 2.427,1.833 2.792,2.01 0.365,0.177 10 false MIN- 2.656,1.615 3.104,1.792 0.448,0.177 10 false SGND 2.76,0.323 3.208,0.5 0.448,0.177 10 false MACC 0.083,0.083 0.323,0.26 0.24,0.177 10 false *a 0.229,1.031 0.573,1.208 0.344,0.177 10 false J135

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J135-19 (MIN-) - Body ground Always Below 1 Ω
J135-18 (SGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J135-4 (MACC) - Body ground Ignition switch ACC 4.75 to 5.25 V


Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)

Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY)

B

C

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY)
a.

Disconnect the J135 navigation receiver assembly connector.


b.

Disconnect the W7 roof console box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J135-4 (MACC) - W7-10 (ACC) Always Below 1 Ω
J135-5 (MIN+) - W7-9 (MI1+) Always Below 1 Ω
J135-19 (MIN-) - W7-8 (MIC-) Always Below 1 Ω
J135-6 (SNS2) - W7-14 (SGND) Always Below 1 Ω
J135-4 (MACC) - Body ground Always 10 kΩ or higher
J135-5 (MIN+) - Body ground Always 10 kΩ or higher
J135-19 (MIN-) - Body ground Always 10 kΩ or higher
J135-18 (SGND) - Body ground Always 10 kΩ or higher
J135-6 (SNS2) - Body ground Always 10 kΩ or higher




OK

3.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL).


b.

Check if the same problem occurs again.

OK:

Malfunction disappears.




OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE ROOF CONSOLE BOX ASSEMBLY