Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234441 INTUITIVE PARKING ASSIST SYSTEM U

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  TERMINALS OF ECU  


CHECK CLEARANCE WARNING ECU ASSEMBLY


U152937E02
3.479,0.25 3.813,0.427 0.333,0.177 10 false J35

a.

Disconnect the J35 clearance warning ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J35-11 (IG) - J35-16 (E) BE - W-B Power source (IG) Ignition switch ON, back sonar or clearance sonar switch assembly OFF Below 1 V
Ignition switch ON, back sonar or clearance sonar switch assembly ON 11 to 14 V
J35-16 (E) - Body ground W-B - Body ground ECU ground Always Below 1 Ω


c.

Reconnect the J35 clearance warning ECU assembly connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J35-2 (ER) - J35-16 (E) V - W-B Clearance warning buzzer Ignition switch ON, back sonar or clearance sonar switch assembly ON, shift lever in R and sensor is detecting state (buzzer sounding) Pulse generation (See waveform 1)
Buzzer not sounding 11 to 14 V
J35-3 (BOF) - J35-16 (E) R - W-B Ultrasonic sensor power source Ignition switch ON, back sonar or clearance sonar switch assembly ON 7.2 to 8.8 V
J35-4 (E5) - J35-16 (E) G - W-B ECU ground Always Below 1 Ω
J35-5 (SOF) - J35-4 (E5) L - G Front sensor communication signal Ignition switch ON, back sonar or clearance sonar switch assembly ON, shift lever except R Pulse generation (See waveform 3)
J35-6 (PL) - J35-16 (E) GR - W-B Parking position signal Ignition switch ON, shift lever not in P position Below 1.5 V
Ignition switch ON, shift lever in P position 7 V or higher
J35-7 (L1) - J35-16 (E) G - W-B Rear corner ultrasonic sensor RH Clearance warning indicator LED for rear corner sensor RH illuminates Below 3 V
J35-8 (L2) - J35-16 (E) GR - W-B Rear corner ultrasonic sensor LH Clearance warning indicator LED for rear corner sensor RH illuminates Below 3 V
J35-9 (L4) - J35-16 (E) B - W-B Front corner ultrasonic sensor RH Clearance warning indicator LED for front corner sensor RH illuminates Below 3 V
J35-10 (L10) - J35-16 (E) R - W-B Clearance warning ECU signal Clearance warning indicator's operation indicator illuminates Below 3 V
J35-12 (BOR) - J35-16 (E) Y - W-B Ultrasonic sensor power source Ignition switch ON, back sonar or clearance sonar switch assembly ON 7.2 to 8.8 V
J35-13 (E1) - J35-16 (E) GR - W-B ECU ground Always Below 1 Ω
J35-14 (SOR) - J35-13 (E1) LG - GR Rear sensor communication signal Ignition switch ON, back sonar or clearance sonar switch assembly ON, shift lever in R Pulse generation (See waveform 2)
J35-17 (SPD) - J35-16 (E) V - W-B Vehicle speed signal Ignition switch ON, drive wheels are turned slowly Alternating between 1.5 to 4.5 V
J35-21 (RL) - J35-16 (E) W - W-B Reverse position signal Ignition switch ON, shift lever not in R Below 1.5 V
Ignition switch ON, shift lever in R 7 V or higher
J35-23 (L3) - J35-16 (E) BE - W-B Rear center ultrasonic sensor Clearance warning indicator LED for rear center sensor illuminates Below 3 V
J35-24 (L5) - J35-16 (E) LG - W-B Front corner ultrasonic sensor LH Clearance warning indicator LED for front corner sensor LH illuminates Below 3 V


e.
E285889E02
0.083,1.698 0.531,1.948 0.448,0.25 10 false GND

Using an oscilloscope, check waveform 1.

Measurement Condition
Item Content
Terminal No. (Symbol) J35-2 (ER) - J35-16 (E)
Tool Setting 2 V/DIV., 200 μsec./DIV.
Condition Ignition switch ON, back sonar or clearance sonar switch assembly ON, shift lever in R and sensor is detecting state (buzzer sounding)


f.
E235241E03
0.177,0.948 0.531,1.094 0.354,0.146 10 false GND

Using an oscilloscope, check waveform 2.

Measurement Condition
Item Content
Terminal No. (Symbol) J35-14 (SOR) - J35-13 (E1)
Tool Setting 2 V/DIV., 200 μsec./DIV.
Condition Ignition switch ON, back sonar or clearance sonar switch assembly ON, shift lever in R


g.
E235241E03
0.177,0.948 0.531,1.094 0.354,0.146 10 false GND

Using an oscilloscope, check waveform 3.

Measurement Condition
Item Content
Terminal No. (Symbol) J35-5 (SOF) - J35-4 (E5)
Tool Setting 2 V/DIV., 200 μsec./DIV.
Condition Ignition switch ON, back sonar or clearance sonar switch assembly ON, shift lever except R