Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234441 INTUITIVE PARKING ASSIST SYSTEM D

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  OPERATION CHECK  


CHECK INITIAL CHECK FUNCTION


a.

Check the initial check function for the sensor.

·

Approximately 0.4 seconds after the ignition switch has been turned to the ON position and the back sonar or clearance sonar switch assembly has been turned ON, all sensors will be checked by the system.

·

When the vehicle has been shifted from P, the system will change to the obstacle detection operation according to the shift position.

·

If there are no changes in the conditions, such as those listed above (speed or shift position), the sensor check operation will be halted after approximately 5 seconds have elapsed. If one or more sensors are anomalous, check operation for all of the sensors will continue (sensors will continue transmitting).




MALFUNCTION DISPLAY (MULTI-INFORMATION DISPLAY)


a.

Open circuit indication

i.

If there is an open circuit between the ultrasonic sensor and the clearance warning ECU assembly or a sensor is malfunctioning, the malfunction is displayed as shown in the illustration.

E282795E02
1.896,1.823 1.719,2.208 1.719,2.208 1.594,2.208 true 5.146,1.813 4.365,2.083 4.365,2.083 4.177,2.083 true 5.146,0.875 4.375,2.083 true 5.844,1.781 6.406,1.781 true 5.823,0.865 6.219,1.115 6.219,1.115 6.219,1.771 true 5.469,1.823 5.833,2.188 5.833,2.188 5.948,2.188 true 0.135,0.083 1.406,0.406 1.271,0.323 12 false 5 cycles: 3.688,0.094 4.917,0.385 1.229,0.292 12 false After 5 cycles: 1.052,2.125 1.667,2.313 0.615,0.188 10 false Blinking 3.635,1.99 4.25,2.177 0.615,0.188 10 false Blinking 6.479,1.698 7.021,1.885 0.542,0.188 10 false Blinking 6.01,2.115 6.552,2.302 0.542,0.188 10 false Blinking

HINT:
·

The example shows an open circuit in the No. 2 ultrasonic sensor (rear corner sensor RH).

·

The rear right detection area blinks and the other indicator areas are not illuminated (5 cycles).

·

The rear right detection area blinks (after 5 cycles).

·
E275663

If "CHECK SONAR SYSTEM, SEE DEALER" is displayed, refer to "System check indication is displayed in self-check function" in the Problem Symptoms Table to inspect the problem (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTUITIVE PARKING ASSIST SYSTEM>PROBLEM SYMPTOMS TABLE).

·

It is not trouble other than the rear corner sensor RH in this example. Please do not change it other than the rear corner sensor RH.





b.

Frozen indication

i.

If a sensor is covered with foreign matter, such as mud or snow, the affected sensor is displayed as shown in the illustration.

E282796E02
5.167,0.938 5.292,0.469 5.292,0.469 6.229,0.469 true 5.823,0.938 5.948,0.469 true 1.99,1.917 1.813,2.302 1.813,2.302 1.688,2.302 true 5.792,1.885 5.698,2.323 5.698,2.323 4.458,2.323 true 5.135,1.896 5.031,2.323 true 5.469,1.896 5.385,2.323 true 0.115,0.094 1.417,0.417 1.302,0.323 12 false 5 cycles: 3.771,0.094 5,0.344 1.229,0.25 12 false After 5 cycles: 0.969,2.219 2.208,2.406 1.24,0.188 10 false Illuminated 3.708,2.188 4.521,2.375 0.813,0.188 10 false Illuminated 6.313,0.385 7.042,0.573 0.729,0.188 10 false Illuminated

HINT:
·

The example shows that the No. 2 ultrasonic sensor (rear corner sensor RH) is covered with foreign matter.

·

The rear right detection area illuminates and the other indicator areas are not illuminated (5 cycles).

·

All indicator areas illuminate (after 5 cycles).

·
E275659

If "CLEAN SONAR" is displayed, refer to "Frozen indication is displayed in self-check function" in the Problem Symptoms Table to inspect the problem (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTUITIVE PARKING ASSIST SYSTEM>PROBLEM SYMPTOMS TABLE).

·

It is not trouble other than the rear corner sensor RH in this example. Please do not change it other than the rear corner sensor RH.






DETECTION RANGE MEASUREMENT AND INDICATOR CHECK


NOTICE:

Make sure that the vehicle does not move by applying the parking brake firmly.


a.

Turn the ignition switch to ON.


b.

Move the shift lever to R to check the front corner sensors, rear corner sensors and back sensors.


c.

Move the shift lever to the D, S and N position to check the front corner sensors.


d.

Turn the back sonar or clearance sonar switch assembly ON.


e.

Move a pole around the sensor to measure the detection range of the sensor.

NOTICE:
·

These detection ranges are applicable when positioning the pole parallel or perpendicular to the ground.

·

The ranges vary depending on the measuring method and type of obstacle (such as walls).

·

For close-range, medium-range detection and long-range detection, the values shown are for when using a pole with a diameter of 60 mm (2.36 in.). For longest-range detection, the values shown are for when using a pole with a diameter of 400 mm (15.7 in.).

·

The detection range of the resin bumper and steel bumper are not the same, as their installation positions are slightly different.



i.

Front corner sensors detection range

E280636E02
1.229,0.698 1.49,0.396 1.49,0.396 1.552,0.396 false 1.385,0.875 1.531,0.719 1.531,0.719 1.76,0.719 false 4.344,2.76 3.927,2.865 false 1.625,0.292 4.615,0.521 2.99,0.229 10 false Approximately 600 +/-60 mm (23.6 +/-2.36 in.) 1.833,0.625 3.99,0.885 2.156,0.26 10 false Approximately 200 mm (7.87 in.) 3.01,2.177 4.083,2.594 1.073,0.417 10 false Approximately 440 mm (17.3 in.) 3.01,2.771 4.115,3.177 1.104,0.406 10 false Approximately 420 mm (16.5 in.)


ii.

Rear corner sensors detection range

E280660E02
2.969,0.76 3.115,0.313 3.115,0.313 3.531,0.313 false 6.125,2.521 6.698,1.521 6.698,1.521 6.417,1.521 false 6.125,2.771 6.563,3.208 6.563,3.208 6.177,3.208 false 2.615,0.813 2.583,0.49 2.583,0.49 2.323,0.49 false 3.625,0.208 5.542,0.573 1.917,0.365 10 false Approximately 850 +/-90 mm (33.5 +/-3.54 in.) 0.271,0.385 2.448,0.781 2.177,0.396 10 false Approximately 200 mm (7.87 in.) 4.375,1.427 6.49,1.823 2.115,0.396 10 false Approximately 550 mm (21.7 in.) 4.229,3.135 6.313,3.531 2.083,0.396 10 false Approximately 220 mm (8.7 in.)


iii.

Rear center sensors detection range

E280644E02
6.583,2.49 7.031,1.531 7.031,1.531 6.677,1.531 false 6.594,2.813 6.927,3.188 6.927,3.188 6.604,3.188 false 2.052,0.854 2.208,0.406 2.208,0.406 2.344,0.406 false 1.656,0.854 1.594,0.385 1.594,0.385 1.302,0.385 false 2.417,0.302 5.813,0.552 3.396,0.25 10 false Approximately 1800 +/-180 mm (70.9 +/-7.09 in.) 0.198,0.302 1.281,0.75 1.083,0.448 10 false Approximately 200 mm (7.87 in.) 4.573,3.125 6.656,3.563 2.083,0.438 10 false Approximately 200 mm (7.87 in.) 4.635,1.458 6.76,1.896 2.125,0.438 10 false Approximately 650 mm (25.6 in.)



f.

When the No. 1 ultrasonic sensors (front corner sensor) have detected an obstacle, check the multi-information display displays and buzzer sounds.

Operation Condition
Ignition Switch Back Sonar or Clearance Sonar Switch Assembly Shift Lever Position Vehicle Speed
ON ON D, S, N, R 10 km/h (6.2 mph) or less

i.

Check the buzzer sounds with the back sonar or clearance sonar switch assembly ON.

E270548E03
0.125,0.219 1.792,0.427 1.667,0.208 10 false 1. Close-range Detection 0.125,1.083 2.156,1.292 2.031,0.208 10 false 2. Medium-range Detection 0.125,2.333 1.917,2.542 1.792,0.208 10 false 3. Long-range Detection 2.469,0.438 2.771,0.583 0.302,0.146 10 false ON 2.469,0.854 2.833,1 0.365,0.146 10 false OFF 2.469,1.729 2.771,1.875 0.302,0.146 10 false ON 2.469,2.146 2.833,2.292 0.365,0.146 10 false OFF 2.469,2.969 2.771,3.115 0.302,0.146 10 false ON 2.469,3.385 2.833,3.531 0.365,0.146 10 false OFF 1.198,1.385 2.75,1.594 1.552,0.208 10 false 0.75 +/-0.075 seconds 1.188,2.594 2.75,2.781 1.563,0.188 10 false 0.15 +/-0.015 seconds 4.625,2.594 6.25,2.75 1.625,0.156 10 false 0.15 +/-0.015 seconds 4.323,1.375 6,1.531 1.677,0.156 10 false 0.75 +/-0.07.5 seconds

Front corner detection range
Detection Distance
1. Close-range detection Within 300 +/-30 mm (11.8 +/-1.18 in.)
2. Medium-range detection 300 +/-30 to 450 +/-50 mm (11.8 +/-1.18 to 17.7 +/-1.97 in.)
3. Long-range detection 450 +/-50 to 600 +/-60 mm (17.7 +/-1.97 to 23.6 +/-2.36 in.)

HINT:

Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.



ii.
E275662

Check the indicator and buzzer on the combination meter assembly when the front corner sensors have detected an obstacle.

Combination meter assembly
Detection Range Buzzer Indicator displayed
1. Close-range detection Sounds continuously Corner indicator(s) are blinking
2. Medium-range detection Sounds intermittently
(ON: 75 msec. / OFF: 75 msec.)
Corner indicator(s) are illuminated
3. Long-range detection Sounds intermittently
(ON: 150 msec. / OFF: 150 msec.)
Corner indicator(s) are illuminated

HINT:

Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.




g.

When the No. 2 ultrasonic sensors (rear corner sensor) have detected an obstacle, check the multi-information display in the combination meter assembly displays and buzzer in the combination meter assembly sounds with the back sonar or clearance sonar switch assembly ON.

Operation Condition
Ignition Switch Back Sonar or Clearance Sonar Switch Assembly Shift Lever Position Vehicle Speed
ON ON R No Limit

i.

Check the buzzer sounds with the back sonar or clearance sonar switch assembly ON.

E270548E03
0.125,0.219 1.792,0.427 1.667,0.208 10 false 1. Close-range Detection 0.125,1.083 2.156,1.292 2.031,0.208 10 false 2. Medium-range Detection 0.125,2.333 1.917,2.542 1.792,0.208 10 false 3. Long-range Detection 2.469,0.438 2.771,0.583 0.302,0.146 10 false ON 2.469,0.854 2.833,1 0.365,0.146 10 false OFF 2.469,1.729 2.771,1.875 0.302,0.146 10 false ON 2.469,2.146 2.833,2.292 0.365,0.146 10 false OFF 2.469,2.969 2.771,3.115 0.302,0.146 10 false ON 2.469,3.385 2.833,3.531 0.365,0.146 10 false OFF 1.198,1.385 2.75,1.594 1.552,0.208 10 false 0.75 +/-0.075 seconds 1.188,2.594 2.75,2.781 1.563,0.188 10 false 0.15 +/-0.015 seconds 4.625,2.594 6.25,2.75 1.625,0.156 10 false 0.15 +/-0.015 seconds 4.323,1.375 6,1.531 1.677,0.156 10 false 0.75 +/-0.07.5 seconds

Rear corner detection range
Detection Distance
1. Close-range detection Within 400 +/-40 mm (15.7 +/-1.57 in.)
2. Medium-range detection 400 +/-40 to 600 +/-60 mm (15.7 +/-1.57 to 23.6 +/-2.36 in.)
3. Long-range detection 600 +/-60 to 850 +/-90 mm (23.6 +/-2.36 to 33.5 +/-3.54 in.)

HINT:

Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.



ii.
E285887

Check the combination meter assembly and buzzer when the rear corner sensors have detected an obstacle.

Combination meter assembly
Detection Range Buzzer Indicator displayed
1. Close-range detection Sounds continuously Corner indicator(s) are blinking
2. Medium-range detection Sounds intermittently
(ON: 75 msec. / OFF: 75 msec.)
Corner indicator(s) are illuminated
3. Long-range detection Sounds intermittently
(ON: 150 msec. / OFF: 150 msec.)
Corner indicator(s) are illuminated

HINT:

Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.




h.

When the No. 3 ultrasonic sensors (rear center sensor) have detected an obstacle, check the multi-information display displays and buzzer in the combination meter assembly sounds with the back sonar or clearance sonar switch assembly ON.

Operation Condition
Ignition Switch Back Sonar or Clearance Sonar Switch Assembly Shift Lever Position Vehicle Speed
ON ON R No limit

i.

Check the buzzer sounds with the back sonar or clearance sonar switch assembly ON.

E270549E03
0.104,0.146 1.771,0.354 1.667,0.208 10 false 1. Close-range Detection 0.104,1.01 2.135,1.219 2.031,0.208 10 false 2. Medium-range Detection 0.104,2.26 1.896,2.469 1.792,0.208 10 false 3. Long-range Detection 2.49,0.365 2.792,0.51 0.302,0.146 10 false ON 2.49,0.792 2.854,0.938 0.365,0.146 10 false OFF 2.49,1.635 2.792,1.781 0.302,0.146 10 false ON 2.49,2.073 2.854,2.219 0.365,0.146 10 false OFF 2.49,2.865 2.792,3.01 0.302,0.146 10 false ON 2.49,3.292 2.854,3.438 0.365,0.146 10 false OFF 1.281,1.302 2.698,1.458 1.417,0.156 10 false 0.75 +/-0.075 seconds 1.271,2.521 2.729,2.677 1.458,0.156 10 false 0.15 +/-0.015 seconds 4.719,2.521 6.26,2.677 1.542,0.156 10 false 0.15 +/-0.015 seconds 0.104,3.438 1.896,3.646 1.792,0.208 10 false 4. Longest-range Detection 2.49,4.01 2.792,4.156 0.302,0.146 10 false ON 2.49,4.448 2.854,4.594 0.365,0.146 10 false OFF 1.281,3.688 2.813,3.844 1.531,0.156 10 false 0.15 +/-0.015 seconds 5.323,3.667 6.75,3.823 1.427,0.156 10 false 0.65 +/-0.065 seconds 4.365,1.313 6.24,1.469 1.875,0.156 10 false 0.75 +/-0.075 seconds

Rear center detection range
Detection Distance
1. Close-range detection Within 500 +/-50 mm (19.7 +/-1.97 in.)
2. Medium-range detection 500 +/-50 to 750 +/-80 mm (19.7 +/-1.97 to 29.5 +/-2.95 in.)
3. Long-range detection 750 +/-80 to 1000 +/-100 mm (29.5 +/-2.95 to 39.4 +/-3.94 in.)
4. Longest-range detection 1000 +/-100 to 1800 +/-180 mm (39.4 +/-3.94 to 70.9 +/-7.09 in.)

HINT:

Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.



ii.
E285888

Check the combination meter assembly and buzzer when the rear center sensors have detected an obstacle.

Combination meter assembly
Detection Range Buzzer Indicator displayed
1. Close-range detection Sounds continuously Rear center indicator is blinking
2. Medium-range detection Sounds intermittently
(ON: 75 msec. / OFF: 75 msec.)
Rear center indicator is illuminated
3. Long-range detection Sounds intermittently
(ON: 150 msec. / OFF: 150 msec.)
Rear center indicator is illuminated

HINT:

Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.