Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E244551E49
0.333,0.719 1.198,1.125 0.865,0.406 10 false from IG No.1 Relay 6.365,0.875 7.135,1.073 0.771,0.198 10 false to CAN 0.854,5.302 2.646,5.51 1.792,0.208 10 false : CAN Communication Line 1.646,0.875 2.771,1.188 1.125,0.313 10 false ECU-IG No.1 3.635,0.719 4.094,0.917 0.458,0.198 10 false BRB 3.635,3.292 4.094,3.49 0.458,0.198 10 false BLB 3.635,1.521 4.198,1.75 0.563,0.229 10 false BRGD 3.625,4.083 4.188,4.313 0.563,0.229 10 false BLGD 3.385,0.594 3.594,0.802 0.208,0.208 10 false 5 3.385,3.167 3.594,3.375 0.208,0.208 10 false 5 3.333,1.375 3.594,1.583 0.26,0.208 10 false 10 3.333,3.958 3.594,4.167 0.26,0.208 10 false 10 3.49,2.031 3.948,2.229 0.458,0.198 10 false S6 3.49,2.208 4.865,2.573 1.375,0.365 10 false Blind Spot Monitor Sensor RH 3.521,4.625 3.979,4.823 0.458,0.198 10 false S5 3.531,4.781 4.906,5.146 1.375,0.365 10 false Blind Spot Monitor Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH, BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)
a.
U152914E02
1.99,1.281 2.438,0.865 2.438,0.865 2.656,0.865 true 1.969,1.51 2.396,2.031 2.396,2.031 2.615,2.031 true 1.99,3.594 2.438,3.177 2.438,3.177 2.656,3.177 true 1.948,3.792 2.375,4.313 2.375,4.313 2.594,4.313 true 0.104,0.063 0.469,0.313 0.365,0.25 10 false *a 1.594,0.417 1.958,0.594 0.365,0.177 10 false S6 2.698,0.792 3.063,0.969 0.365,0.177 10 false BRB 1.604,2.677 1.969,2.844 0.365,0.167 10 false S5 2.667,1.938 3.115,2.115 0.448,0.177 10 false BRGD 0.104,2.323 0.469,2.573 0.365,0.25 10 false *b 2.698,3.083 3.063,3.26 0.365,0.177 10 false BLB 2.667,4.219 3.115,4.396 0.448,0.177 10 false BLGD

Disconnect the blind spot monitor sensor RH connector.


b.

Disconnect the blind spot monitor sensor LH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S6-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
S6-5 (BRB) - Body ground Ignition switch off Below 1 V
S5-5 (BLB) - Body ground Ignition switch ON 11 to 14 V
S5-5 (BLB) - Body ground Ignition switch off Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-10 (BRGD) - Body ground Always Below 1 Ω
S5-10 (BLGD) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
*b Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR