Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.



CHECK FREEZE FRAME DATA


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the blind spot monitor main switch assembly (warning canceling switch assembly) on.


d.

Turn the Techstream on.


e.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.


f.

According to the display on the Techstream, display the Freeze Frame Data for the selected DTC.

Blind Spot Monitor Master
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main Switch Blind spot monitor main switch assembly (warning canceling switch assembly) / OFF or ON ON: Blind spot monitor main switch assembly (warning canceling switch assembly) on
OFF: Blind spot monitor main switch assembly (warning canceling switch assembly) off
-
Warning Indicator Turning on (Master) State of the outer rear view mirror indicator RH turning on / OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in warning area

·

Vehicle speed 16 km/h (10 mph) or more

·

Shift lever in any position except R

·

No DTC output



-
Warning Indicator Flashing (Master) State of the outer rear view mirror indicator RH flashing / OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in warning area

·

Vehicle speed 16 km/h (10 mph) or more

·

Shift lever in any position except R

·

No DTC output



-
Main Switch Indicator Status State of the blind spot monitor indicator on the blind spot monitor main switch assembly (warning canceling switch assembly) / OFF or ON OFF: Indicator not illuminated
ON: Indicator illuminated
-
Warning Indicator Input Circuit Voltage The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V Not illuminated: 0 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Right Turn SW State (CAN) State of the headlight dimmer switch assembly (right turn signal light switch) / ON or OFF ON: Right side of turn signal light switch on
OFF: Right side of turn signal light switch off
-
Left Turn SW State (CAN) State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF ON: Left side of turn signal light switch on
OFF: Left side of turn signal light switch off
-
Reverse State of the shift position R signal / OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering sensor / Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Number of DTC Number of DTC / Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-

Blind Spot Monitor Slave
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Warning Indicator Turning on (Slave) State of the outer rear view mirror indicator LH turning on / OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in warning area

·

Vehicle speed 16 km/h (10 mph) or more

·

Shift lever in any position except R

·

No DTC output



-
Warning Indicator Flashing (Slave) State of the outer rear view mirror indicator LH flashing / OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in warning area

·

Vehicle speed 16 km/h (10 mph) or more

·

Shift lever in any position except R

·

No DTC output



-
Buzzer Sound Status State of the rear cross traffic alert buzzer (blind spot monitor buzzer) / OFF or ON OFF: Buzzer not sounding

ON: All of the following conditions are met:

·

Not during initial check

·

Vehicle detected in warning area of rear cross traffic alert

·

Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more

·

Shift lever in R

·

No DTC output



-
Warning Indicator Input Circuit Voltage The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V Not illuminated: 0 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Buzzer Input Circuit Voltage Rear cross traffic alert buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V Not sounding buzzer: 11 to 14 V
Sounding buzzer: Alternating between 0 to 14 V
-
Right Turn SW State (CAN) State of the headlight dimmer switch assembly (right signal light switch) / ON or OFF ON: Right side of turn signal light switch on
OFF: Right side of turn signal light switch off
-
Left Turn SW State (CAN) State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF ON: Left side of turn signal light switch on
OFF: Left side of turn signal light switch off
-
Reverse State of the shift position R signal / OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering sensor / Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Number of DTC Number of DTC / Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-



CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the Freeze Frame Data


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the blind spot monitor main switch assembly (warning canceling switch assembly) on.


d.

Turn the Techstream on.


e.

Clear the DTCs and Freeze Frame Data.