Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234451 REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) C

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

This DTC is stored if the navigation receiver assembly judges as a result of its self check that the signals or signal lines between the navigation receiver assembly and the television camera assembly are not normal.

DTC Code DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in television camera signal
·

Harness or connector

·

Television camera assembly

·

Navigation receiver assembly



WIRING DIAGRAM

E224828E27
0.219,2.813 0.583,2.958 0.365,0.146 10 false X1 0.208,2.979 1.75,3.354 1.542,0.375 10 false Television Camera Assembly 5.604,2.833 6.063,2.979 0.458,0.146 10 false J136 5.76,2.365 6.198,2.51 0.438,0.146 10 false CGND 5.76,1.469 6.198,1.615 0.438,0.146 10 false V+ 5.76,1.948 6.198,2.094 0.438,0.146 10 false V- 5.76,1 6.198,1.146 0.438,0.146 10 false CA+ 1.01,2.385 1.448,2.531 0.438,0.146 10 false CGND 1.135,1.469 1.448,1.615 0.313,0.146 10 false CV+ 1.156,1.948 1.448,2.094 0.292,0.146 10 false CV- 1.146,1.01 1.448,1.156 0.302,0.146 10 false CB+ 1.542,2.271 1.75,2.417 0.208,0.146 10 false 5 1.542,1.344 1.688,1.49 0.146,0.146 10 false 3 1.542,1.844 1.688,1.99 0.146,0.146 10 false 2 1.542,0.885 1.688,1.031 0.146,0.146 10 false 6 5.479,2.271 5.667,2.469 0.188,0.198 10 false 23 5.49,1.354 5.677,1.542 0.188,0.188 10 false 12 5.49,1.844 5.667,2.01 0.177,0.167 10 false 24 5.479,0.875 5.667,1.063 0.188,0.188 10 false 11 0.198,3.448 0.969,3.667 0.771,0.219 10 false *: Shielded 2.427,2.542 2.594,2.708 0.167,0.167 10 false * 5.615,3.01 6.885,3.365 1.271,0.354 10 false Navigation Receiver Assembly 3.542,2.542 3.708,2.708 0.167,0.167 10 false * 4.677,2.542 4.844,2.708 0.167,0.167 10 false *

PROCEDURE

1.CHECK FOR DTC

A

B

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the J136 navigation receiver assembly connector.


b.

Disconnect the X1 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J136-11 (CA+) - X1-6 (CB+) Always Below 1 Ω
J136-12 (V+) - X1-3 (CV+) Always Below 1 Ω
J136-23 (CGND) - X1-5 (CGND) Always Below 1 Ω
J136-24 (V-) - X1-2 (CV-) Always Below 1 Ω
J136-11 (CA+) - Body ground Always 10 kΩ or higher
J136-12 (V+) - Body ground Always 10 kΩ or higher
J136-23 (CGND) - Body ground Always 10 kΩ or higher
J136-24 (V-) - Body ground Always 10 kΩ or higher




OK

3.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
U152843E02
0.938,1.281 0.688,1.531 0.688,1.531 0.479,1.531 true 1.083,1.281 0.938,1.906 0.938,1.906 0.813,1.906 true 1.594,0.292 2.042,0.458 0.448,0.167 10 false J136 0.375,1.833 0.865,2.031 0.49,0.198 10 false CGND 0.271,1.438 0.51,1.635 0.24,0.198 10 false V- 0.115,0.073 0.354,0.271 0.24,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J136-23 (CGND) - Body ground Always Below 1 Ω
J136-24 (V-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)

Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

4.CHECK NAVIGATION RECEIVER ASSEMBLY

B

C

4.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
U152815E02
1.865,1.521 2.5,1.656 2.5,1.656 2.708,1.656 true 1.677,1.521 1.198,1.646 1.198,1.646 0.844,1.646 true 0.146,0.083 0.542,0.271 0.396,0.188 10 false *a 1.615,0.26 1.833,0.448 0.219,0.188 10 false X1 2.771,1.573 3.208,1.76 0.438,0.188 10 false CB+ 0.406,1.573 0.844,1.76 0.438,0.188 10 false CGND

Disconnect the television camera assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
X1-6 (CB+) - X1-5 (CGND) Ignition switch ACC 5.5 to 7.05 V


Text in Illustration
*a Front view of wire harness connector
(to Television Camera Assembly)

Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

5.CHECK TELEVISION CAMERA ASSEMBLY

B

C

5.CHECK TELEVISION CAMERA ASSEMBLY
a.

Using an oscilloscope, check the waveform.

U152821E02
0.583,1.323 0.5,0.781 0.5,0.781 0.333,0.781 true 0.583,1.51 0.5,2.063 0.5,2.063 0.333,2.063 true 2.792,1.885 2.708,2.438 2.708,2.438 2.552,2.438 false 2.896,1.792 2.979,2.438 2.979,2.438 3.135,2.438 false 5.427,1.74 5.354,2.427 5.354,2.427 5.198,2.427 false 5.552,1.677 5.635,2.417 5.635,2.417 5.792,2.417 false 0.125,0.708 0.365,0.875 0.24,0.167 10 false V+ 0.125,0.125 0.365,0.292 0.24,0.167 10 false *a 2.281,0.115 2.521,0.281 0.24,0.167 10 false *b 2.365,2.354 2.604,2.521 0.24,0.167 10 false *d 4.833,0.104 5.073,0.271 0.24,0.167 10 false *c 2.052,1.354 2.458,1.521 0.406,0.167 10 false GND 1.01,0.729 1.417,0.896 0.406,0.167 10 false J136 4.646,1.354 5.052,1.521 0.406,0.167 10 false GND 0.146,1.979 0.385,2.146 0.24,0.167 10 false V- 3.177,2.344 3.417,2.51 0.24,0.167 10 false *e 4.99,2.333 5.229,2.5 0.24,0.167 10 false *d 5.833,2.323 6.073,2.49 0.24,0.167 10 false *e

Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronized Signal
*e Video Waveform - -

Measurement Condition
Item Content
Tester Connection J136-12 (V+) - J136-24 (V-)
Tool Setting 0.2 V/DIV., 50 μs/DIV.
Condition

Waveform 1: Ignition switch ON

Waveform 2: Ignition switch ON, screen blacked out by covering camera lens



OK:

Waveform is as shown in illustration.


HINT:

The video waveform changes according to the image sent by the television camera assembly.




OK

NG

6.REPLACE TELEVISION CAMERA ASSEMBLY
6.REPLACE TELEVISION CAMERA ASSEMBLY
a.

Replace the television camera assembly with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL).



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR).

Result
Result Proceed to
No DTC is output A
DTC is output (for Column Shift Type) B
DTC is output (for Floor Shift Type) C



A

END (TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

B

C