Home › Vehicle Interior › WINDOW / GLASS › WINDSHIELD DEICER SYSTEM
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234461 WINDSHIELD DEICER SYSTEM J

WINDOW / GLASS  WINDSHIELD DEICER SYSTEM  Windshield Deicer does not Operate  


DESCRIPTION

When the air conditioning control assembly (windshield deicer switch) turns is turned on, a windshield deicer activation request signal is sent via the LIN communication line to the air conditioning amplifier. Then the air conditioning amplifier operates the windshield deicer.

WIRING DIAGRAM

B356784E01
0.231,0.523 1.446,0.693 1.215,0.170 10 from IG No.1 Relay 0.651,0.957 1.450,1.127 0.798,0.170 10 from Battery 2.013,0.691 2.457,0.861 0.444,0.170 10 LH-IG 1.942,1.132 2.511,1.302 0.569,0.170 10 DEICER 3.644,1.322 4.213,1.491 0.569,0.170 10 DEICER 3.186,0.461 3.334,0.659 0.149,0.198 10 1 3.186,0.882 3.334,1.080 0.149,0.198 10 3 4.559,0.461 4.708,0.659 0.149,0.198 10 2 2.247,1.844 2.395,2.042 0.149,0.198 10 2 2.422,1.844 2.570,2.042 0.149,0.198 10 E 3.437,1.844 3.586,2.042 0.149,0.198 10 B 3.613,1.844 3.761,2.042 0.149,0.198 10 1 5.554,0.445 5.791,0.643 0.237,0.198 10 40 5.836,0.523 5.982,0.721 0.146,0.198 10 D 5.836,3.297 6.247,3.495 0.411,0.198 10 LIN1 5.318,3.794 5.611,3.964 0.293,0.170 10 J19 5.318,3.946 6.949,4.165 1.631,0.219 10 Air Conditioning Amplifier 1.995,3.724 2.386,3.894 0.390,0.170 10 J127 1.995,3.876 4.422,4.319 2.426,0.443 10 Air Conditioning Control Assembly (Windshield Deicer Switch) 0.949,4.497 2.598,4.665 1.649,0.168 10 : LIN Communication Line 1.967,2.344 2.306,2.514 0.339,0.170 10 A23 2.935,3.31 3.275,3.481 0.339,0.170 10 STX 1.967,2.493 4.672,2.804 2.705,0.311 10 Windshield Glass (Windshield Deicer Wire) 5.554,3.164 5.791,3.362 0.237,0.198 10 37 4.559,0.882 4.708,1.080 0.149,0.198 10 5 3.288,3.164 3.437,3.362 0.149,0.198 10 7

CAUTION / NOTICE / HINT

HINT:

This circuit uses the LIN communication line. Before performing the inspection, check that the LIN communication system is functioning normally (see page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (WINDSHIELD DEICER RELAY ASSEMBLY)
a.

Select the Active Test using the Techstream to generate a control command, and then check that the windshield deicer operates (see page Vehicle Interior>WINDOW / GLASS>WINDSHIELD DEICER SYSTEM>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Deicer Relay (Front) Windshield deicer relay assembly ON or OFF -

OK:

Windshield deicer relay assembly turns ON and OFF.




OK

2.CHECK AIR CONDITIONING CONTROL ASSEMBLY

NG

3.INSPECT FUSE (DEICER, LH-IG)
2.CHECK AIR CONDITIONING CONTROL ASSEMBLY
a.

Temporarily replace the air conditioning control assembly with a new or normally functioning one (see page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL).


b.

Check that the malfunction disappears.

OK:

Malfunction disappears.




OK

END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER

3.INSPECT FUSE (DEICER, LH-IG)
a.

Remove the DEICER fuse from the engine room relay block, junction block.


b.

Remove the LH-IG fuse from the driver side junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
DEICER fuse Always Below 1 Ω
LH-IG fuse Always Below 1 Ω




OK

4.INSPECT WINDSHIELD DEICER RELAY ASSEMBLY (DEICER)

NG

REPLACE FUSE

4.INSPECT WINDSHIELD DEICER RELAY ASSEMBLY (DEICER)
B356785E03
1.615,0.427 1.979,0.74 true 2.5,1.104 2.906,1.104 true 2.302,1.604 2.302,1.854 true 2.615,0.729 3.01,0.448 true 0.313,0.719 0.438,0.906 0.125,0.188 10 false 3 0.313,1.229 0.438,1.417 0.125,0.188 10 false 1 1.229,1.24 1.354,1.427 0.125,0.188 10 false 2 1.229,0.74 1.354,0.927 0.125,0.188 10 false 5 1.469,0.333 1.656,0.604 0.188,0.271 10 false 1 2.979,1 3.167,1.271 0.188,0.271 10 false 5 2.271,1.906 2.458,2.177 0.188,0.271 10 false 3 3.052,0.323 3.24,0.594 0.188,0.271 10 false 2

a.

Remove the windshield deicer relay assembly (DEICER) from the engine room relay block, junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 5 When battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
When battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIR CONDITIONING AMPLIFIER AND BATTERY)

NG

REPLACE WINDSHIELD DEICER RELAY ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIR CONDITIONING AMPLIFIER AND BATTERY)
B442875E01
4.313,2.229 4.667,2.448 0.354,0.219 2.271,2.927 2.677,2.531 false 4.583,2.75 4.99,2.354 false 0.26,0.156 3.021,0.542 2.76,0.385 10 false Component without relay connected: (Engine Room Relay Block, Junction Block) 4.052,0.156 6.323,0.51 2.271,0.354 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier) 0.76,2.844 2.292,3.198 1.531,0.354 10 false Windshield Deicer Relay Assembly (DEICER) 4.396,2.25 4.656,2.438 0.26,0.188 10 false J19 4.427,2.781 4.583,2.979 0.156,0.198 10 false D

a.

Remove the windshield deicer relay assembly (DEICER) from the engine room relay block, junction block.


b.

Disconnect the J19 air conditioning amplifier connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
Windshield deicer relay assembly (DEICER) terminal 1 - Body ground Ignition switch ON 11 to 14 V
Ignition switch OFF Below 1 V
Windshield deicer relay assembly (DEICER) terminal 3 - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Windshield deicer relay assembly (DEICER) terminal 2 - J19-40 (D) Always Below 1 Ω
Windshield deicer relay assembly (DEICER) terminal 2 or J19-40 (D) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (DEICER RELAY - WINDSHIELD DEICER WIRE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (DEICER RELAY - WINDSHIELD DEICER WIRE)
B442877E01
4.479,1.979 4.896,2.229 0.417,0.25 2.656,2.896 3.01,2.479 false 5.75,2.104 6.208,2.229 false 0.24,0.156 2.99,0.552 2.75,0.396 10 false Component without relay connected: (Engine Room Relay Block, Junction Block) 1.146,2.823 2.667,3.188 1.521,0.365 10 false Windshield Deicer Relay Assembly (DEICER) 4.552,2.01 4.854,2.198 0.302,0.188 10 false A23 6.229,2.177 6.396,2.375 0.167,0.198 10 false B 4.26,0.188 6.531,0.563 2.271,0.375 10 false Front view of wire harness connector: (to Windshield Deicer Wire)

a.

Remove the windshield deicer relay assembly (DEICER) from the engine room relay block, junction block.


b.

Disconnect the A23 windshield glass (windshield deicer wire) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Windshield deicer relay assembly (DEICER) terminal 5 - A23-1 (B) Always Below 1 Ω
Windshield deicer relay assembly (DEICER) terminal 5 or A23-1 (B) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER WIRE - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER WIRE - BODY GROUND)
U151882E01
1.666,1.402 1.182,1.798 false 1.002,1.791 1.158,1.973 0.156,0.181 10 E 0.398,1.154 0.662,1.336 0.264,0.181 10 A23 0.292,0.019 2.687,0.534 2.395,0.515 10 Front view of wire harness connector: (to Windshield Deicer Wire)

a.

Disconnect the A23 windshield glass (windshield deicer wire) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A23-2 (E) - Body ground Always Below 1 Ω




OK

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER POWER SOURCE)
U151883E02
1.667,1.406 1.177,1.802 false 2.115,1.406 2.719,1.802 false 1,1.792 1.156,1.969 0.156,0.177 10 false E 2.75,1.792 2.906,1.969 0.156,0.177 10 false B 0.427,1.208 0.688,1.385 0.26,0.177 10 false A23 0.344,0.031 2.625,0.406 2.281,0.375 10 false Front view of wire harness connector: (to Windshield Deicer Wire)

a.

Disconnect the A23 windshield glass (windshield deicer wire) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A23-1 (B) - A23-2 (E) Ignition switch ON, windshield deicer switch on 11 to 14 V
Ignition switch ON, windshield deicer switch off Below 1 V




OK

NG

REPLACE AIR CONDITIONING AMPLIFIER