85221B
1.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
85211B
2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
53383
3.REMOVE HOOD TO COWL TOP SEAL
53867H
4.REMOVE FRONT FENDER TO COWL SIDE SEAL LH
53866J
5.REMOVE FRONT FENDER TO COWL SIDE SEAL RH
55781E
6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
62312B
7.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Partially remove the front door opening trim weatherstrip LH so that the front pillar garnish LH can be removed (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>REMOVAL).
62311B
8.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedures described for the LH side.
62212
9.REMOVE FRONT PILLAR GARNISH LH
62211
10.REMOVE FRONT PILLAR GARNISH RH
87834
11.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
87810
12.REMOVE INNER REAR VIEW MIRROR ASSEMBLY
w/ EC Mirror:
Remove the inner mirror (see page Vehicle Interior>MIRROR>INNER REAR VIEW MIRROR>REMOVAL).
w/o EC Mirror:
Remove the inner mirror (see page Vehicle Interior>MIRROR>INNER REAR VIEW MIRROR>REMOVAL).
63650A
13.REMOVE ROOF CONSOLE BOX ASSEMBLY
Remove the roof console box (see page Vehicle Interior>INTERIOR>OVERHEAD CONSOLE BOX>REMOVAL).
81240
14.REMOVE NO. 1 ROOM LIGHT ASSEMBLY
74320
15.REMOVE VISOR ASSEMBLY LH
for Regular Cab:
Remove the visor (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>REMOVAL).
for Double Cab:
Remove the visor (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>REMOVAL).
for CrewMax:
Remove the visor (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>REMOVAL).
74310
16.REMOVE VISOR ASSEMBLY RH
Use the same procedures described for the LH side.
74348
17.REMOVE VISOR HOLDER
for Regular Cab:
Remove the visor holder (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>REMOVAL).
for Double Cab, w/o Illumination:
Remove the visor holder (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>REMOVAL).
for CrewMax, w/o Illumination:
Remove the visor holder (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>REMOVAL).
74610A
18.REMOVE ASSIST GRIP SUB-ASSEMBLY
for Regular Cab, for Double Cab:
Remove the assist grip (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>REMOVAL).
for CrewMax:
Remove the assist grip (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>REMOVAL).
74631C
19.REMOVE COAT HOOK
63310
20.REMOVE ROOF HEADLINING ASSEMBLY
Partially remove the roof headlining.
It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.
For Regular Cab, refer to the following procedures (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>REMOVAL).
For Double Cab, refer to the following procedures (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>REMOVAL).
For CrewMax, refer to the following procedures (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>REMOVAL).
75554A
21.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING LH
75553A
22.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING RH
Use the same procedures described for the LH side.
75552
23.REMOVE ROOF DRIP SIDE FINISH MOULDING LH
75551
24.REMOVE ROOF DRIP SIDE FINISH MOULDING RH
Use the same procedures described for the LH side.
75561
25.REMOVE ROOF DRIP SIDE FINISH MOULDING CLIP
75534
26.REMOVE OUTSIDE WINDSHIELD MOULDING
Using a knife, cut off the moulding as shown in the illustration.
Be careful not to damage the vehicle body.
Remove the remaining moulding.
Make a partial cut in the moulding. Then pull and remove it by hand.
27.REMOVE UPPER WINDSHIELD OUTSIDE MOULDING
Using a knife, cut off the moulding as shown in the illustration.
Be careful not to damage the vehicle body.
Remove the remaining moulding.
Make a partial cut in the moulding. Then pull and remove it by hand.
56111
28.REMOVE WINDSHIELD GLASS
w/ Windshield Deicer:
Remove the clip and disconnect the connector.
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.
Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.
Matchmarks do not need to be placed if not reusing the glass.
Cut through the adhesive by pulling the piano wire around the glass.
Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.
Disengage the stoppers.
Using suction cups, remove the glass.
56111
29.CLEAN WINDSHIELD GLASS
Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.
Clean the outer edges of the glass with non-residue solvent.
Even if using new glass, clean it with non-residue solvent.
30.CLEAN VEHICLE BODY
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
Leave as much adhesive on the vehicle body as possible.
Be careful not to damage the vehicle body.
Clean the contact surface of the vehicle body with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.