Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234466 POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)  Power Windows do not Operate at All  


DESCRIPTION

If all of the power windows do not operate, the master switch may have no power or may be malfunctioning.

WIRING DIAGRAM

B166127E04
2.063,1.604 2.281,1.802 0.219,0.198 10 false N2 5.542,1.115 6.354,1.323 0.813,0.208 10 false from Battery 3.521,0.99 4.417,1.156 0.896,0.167 10 false 15*1, 6*2, 6*3 1.125,1 1.948,1.177 0.823,0.177 10 false 7*1, 1*2, 1*3 3.25,1.042 3.552,1.229 0.302,0.188 10 false B 2.135,1.052 2.438,1.24 0.302,0.188 10 false E 0.104,1.885 1.667,2.125 1.563,0.24 10 false *1: for Regular Cab 0.104,2.146 1.688,2.385 1.583,0.24 10 false *2: for Double Cab 0.104,2.406 1.469,2.646 1.365,0.24 10 false *3: for CrewMax 2.063,1.771 5.156,1.969 3.094,0.198 10 false Power Window Regulator Master Switch Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - BATTERY AND BODY GROUND)
U151977E02
2.052,1.76 2.813,1.438 false 1.927,2.021 2.823,2.083 false 1.885,1.771 2.427,1.042 false 1.01,1.74 0.646,1.156 false 0.219,1.802 0.458,1.948 0.24,0.146 10 false N2 2.833,1.281 3.146,1.427 0.313,0.146 10 false E*1 0.125,0.969 0.635,1.146 0.51,0.177 10 false E*2,*3 0.083,2.385 1.427,2.563 1.344,0.177 10 false *1: for Regular Cab 0.083,2.719 1.521,2.896 1.438,0.177 10 false *2: for Double Cab 0.083,3.031 1.292,3.208 1.208,0.177 10 false *3: for CrewMax 2.854,2.031 3.167,2.219 0.313,0.188 10 false B*1 2.458,0.833 2.99,1.021 0.531,0.188 10 false B*2,*3 0.146,0.073 2.49,0.438 2.344,0.365 10 false Front view of wire harness connector: (to Master Switch)

a.

Disconnect the N2 master switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Regular Cab:
Tester Connection Switch Condition Specified Condition
N2-15 (B) - Body ground Ignition switch ON 11 to 14 V

for Double Cab:
Tester Connection Switch Condition Specified Condition
N2-6 (B) - Body ground Ignition switch ON 11 to 14 V

for CrewMax:
Tester Connection Switch Condition Specified Condition
N2-6 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Regular Cab:
Tester Connection Condition Specified Condition
N2-7 (E) - Body ground Always Below 1 Ω

for Double Cab:
Tester Connection Condition Specified Condition
N2-1 (E) - Body ground Always Below 1 Ω

for CrewMax:
Tester Connection Condition Specified Condition
N2-1 (E) - Body ground Always Below 1 Ω




OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR