The circuit detects the conditions of the outer mirror switch.
The outer mirror switch sends information about the operating condition of the mirror switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU. Mirror adjustment is controlled by the outer mirror control ECU.
Use the Techstream to check if the CAN communication system is functioning normally (see page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| CAN DTC is not output | A |
| CAN DTC is output | B |
A
B
Check the DATA LIST for proper functioning of the outer mirror switch.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Mirror Selection SW (Right) | Mirror master switch signal for RH mirror / ON or OFF | ON: Switch is in R position
OFF: Switch is OFF or in L position |
- |
| Mirror Position SW (Right) | Mirror control switch signal (RIGHT) / ON or OFF | ON: RIGHT switch is ON
OFF: Any switch except RIGHT is ON or all switches are OFF |
- |
| Mirror Position SW (Left) | Mirror control switch signal (LEFT) / ON or OFF | ON: LEFT switch is ON
OFF: Any switch except LEFT is ON or all switches are OFF |
- |
| Mirror Position SW (UP) | Mirror control switch signal (UP) / ON or OFF | ON: UP switch is ON
OFF: Any switch except UP is ON or all switches are OFF |
- |
| Mirror Position SW (Down) | Mirror control switch signal (DOWN) / ON or OFF | ON: DOWN switch is ON
OFF: Any switch except DOWN is ON or all switches are OFF |
- |
On screen, each item changes between ON and OFF according to above chart.
OK
NG
Remove the mirror RH (see page Vehicle Interior>MIRROR>OUTER REAR VIEW MIRROR>REMOVAL).
Apply battery voltage and check the operation of the power mirror.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 10 (MV)
Battery negative (-) → Terminal 11 (M+) |
Turns upward (A) |
| Battery negative (-) → Terminal 10 (MV)
Battery positive (+) → Terminal 11 (M+) |
Turns downward (B) |
| Battery positive (+) → Terminal 12 (MH)
Battery negative (-) → Terminal 11 (M+) |
Turns left (C) |
| Battery negative (-) → Terminal 12 (MH)
Battery positive (+) → Terminal 11 (M+) |
Turns right (D) |
OK
NG
Disconnect the N8 ECU connector.
Disconnect the M6 mirror connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N8-38 (M+R) - M6-11 (M+) | Always | Below 1 Ω |
| N8-39 (MHR) - M6-12 (MH) | ||
| N8-40 (MVR) - M6-10 (MV) | ||
| M6-11 (M+) - Body ground | Always | 10 kΩ or higher |
| M6-12 (MH) - Body ground | ||
| M6-10 (MV) - Body ground |
OK
NG
Remove the switch (see page Vehicle Interior>MIRROR>OUTER MIRROR SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (M+) - 2 (E) | UP switch pushed | 100 Ω |
| DOWN switch pushed | 470 Ω | |
| LEFT switch pushed | 800 Ω | |
| RIGHT switch pushed | 250 Ω | |
| 1 (MSW) - 2 (E) | No switches pushed | 10 kΩ or higher |
| R switch pushed | Below 1 Ω |
OK
NG
Disconnect the J4 ECU connector.
Disconnect the J131 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J4-2 (MIRE) - J131-2 (E) | Always | Below 1 Ω |
| J4-11 (MIRB) - J131-3 (M+) | ||
| J4-12 (MIRS) - J131-1 (MSW) | ||
| J131-2 (E) - Body ground | Always | 10 kΩ or higher |
| J131-3 (M+) - Body ground | ||
| J131-1 (MSW) - Body ground |
OK
NG