Home › Vehicle Interior › SLIDING ROOF › SLIDING ROOF SYSTEM
RM27M0U _58 Vehicle Interior _049166 SLIDING ROOF _0234506 SLIDING ROOF SYSTEM J

SLIDING ROOF  SLIDING ROOF SYSTEM  Sliding Roof ECU Power Source Circuit  


DESCRIPTION

If the sliding function and tilt function do not operate, there may be a malfunction in the sliding roof ECU power source circuit.

WIRING DIAGRAM

B171240E05
4.962,1.932 5.378,2.168 0.416,0.236 10 W3 5.175,1.398 5.383,1.608 0.208,0.210 10 E 5.175,0.375 5.439,0.585 0.263,0.210 10 IG 4.913,0.277 5.079,0.487 0.166,0.210 10 9 4.885,0.81 5.079,1.019 0.194,0.210 10 10 4.936,1.3 5.130,1.510 0.194,0.210 10 8 5.175,0.908 5.439,1.118 0.263,0.210 10 B 4.962,2.096 6.600,2.294 1.638,0.199 10 Sliding Roof Drive Gear 0.423,0.368 1.765,0.566 1.342,0.199 10 from IG1 No.2 Relay 0.929,0.884 1.771,1.083 0.842,0.199 10 from Battery 3.337,1.089 3.957,1.288 0.620,0.199 10 S/ROOF 4.944,2.399 6.526,2.574 1.582,0.174 10 - Sliding Roof ECU 3.995,1.888 4.193,1.888 false 4.024,1.929 4.163,1.929 false 4.044,1.97 4.142,1.97 false 3.229,0.511 4.170,0.674 0.941,0.163 10 ECU-IG No.2

PROCEDURE

1.READ VALUE USING TECHSTREAM (IGNITION SWITCH SIGNAL)
a.

Use the Data List to check if the ignition switch signal is functioning properly (see page Vehicle Interior>SLIDING ROOF>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).

Sliding Roof
Tester Display Test Part Control Range Diagnostic Note
Ignition (MPX) Ignition switch signal (MPX signal)/ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
-
Ignition (Direct Signal) Ignition switch signal/ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
-

OK:

The Techstream displays as shown in the table according to the operation of each switch.




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

2.INSPECT FUSE (S/ROOF, ECU-IG No.2)
2.INSPECT FUSE (S/ROOF, ECU-IG No.2)
a.

Remove the S/ROOF and ECU-IG No.2 fuses from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
S/ROOF fuse Always Below 1 Ω
ECU-IG No.2 fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY GROUND)
U151866E02
2.104,2.458 1.938,2.854 false 1.813,2.458 1.5,2.885 false 2.365,2.448 2.521,2.771 false 0.094,0.052 2.344,0.417 2.25,0.365 10 false Front view of wire harness connector: (to Sliding Roof ECU) 1.563,1.208 1.813,1.354 0.25,0.146 10 false W3 1.833,2.875 2.021,3.042 0.188,0.167 10 false IG 1.385,2.896 1.573,3.063 0.188,0.167 10 false E 2.49,2.813 2.74,2.979 0.25,0.167 10 false B

a.

Disconnect the W3 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage :
Tester Connection Condition Specified Condition
W3-9 (IG) - Body ground Ignition switch ON 11 to 14 V
W3-9 (IG) - Body ground Ignition switch off Below 1 V
W3-10 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
W3-8 (E) - Body ground Always Below 1 Ω




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR