If either the sliding function or tilt function does not operate, there may be a malfunction in the sliding roof switch circuit.
Select the Active Test, use the Techstream to generate a control command, and then check that the sliding roof operates (see page Vehicle Interior>SLIDING ROOF>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding roof SLIDE CLOSE/TILT UP or SLIDE OPEN/TILT DOWN | Clos/Up: Sliding roof SLIDE CLOSE or TILT UP operation occurs
Opn/Dwn: Sliding roof SLIDE OPEN or TILT DOWN operation occurs OFF: Sliding roof is not operating |
- |
Sliding roof operates normally.
OK
NG
Use the Data List to check if the sliding roof switch is functioning properly (see page Vehicle Interior>SLIDING ROOF>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Open Switch | Sliding roof open switch signal/ON or OFF | ON: SLIDE switch is pressed to open
OFF: SLIDE switch is not pressed to open |
- |
| Close Switch | Sliding roof close switch signal/ON or OFF | ON: SLIDE switch is pressed to close
OFF: SLIDE switch is not pressed to close |
- |
| Up Switch | Sliding roof up switch signal/ON or OFF | ON: TILT switch is pressed to up
OFF: TILT switch is not pressed to up |
- |
| Down Switch | Sliding roof down switch signal/ON or OFF | ON: TILT switch is pressed to down
OFF: TILT switch is not pressed to down |
- |
The Techstream displays as shown in the table according to the operation of each switch.
OK
NG
Remove the sliding roof switch (see page Vehicle Interior>SLIDING ROOF>SLIDING ROOF SWITCH ASSEMBLY(for CrewMax)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (UP) - 5 (E) | TILT switch is pressed to up | Below 1 Ω |
| 1 (UP) - 5 (E) | TILT switch is not pressed to up | 10 kΩ or higher |
| 2 (DWN) - 5 (E) | TILT switch is pressed to down | Below 1 Ω |
| 2 (DWN) - 5 (E) | TILT switch is not pressed to down | 10 kΩ or higher |
| 4 (OPN) - 5 (E) | SLIDE switch is pressed to open | Below 1 Ω |
| 4 (OPN) - 5 (E) | SLIDE switch is not pressed to open | 10 kΩ or higher |
| 3 (CLS) - 5 (E) | SLIDE switch is pressed to close | Below 1 Ω |
| 3 (CLS) - 5 (E) | SLIDE switch is not pressed to close | 10 kΩ or higher |
OK
NG
Remove the roof console box with sliding roof switch (see page Vehicle Interior>INTERIOR>OVERHEAD CONSOLE BOX>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 6 (UP) - 7 (E) | TILT switch is pressed to up | Below 1 Ω |
| 6 (UP) - 7 (E) | TILT switch is not pressed to up | 10 kΩ or higher |
| 5 (DWN) - 7 (E) | TILT switch is pressed to down | Below 1 Ω |
| 5 (DWN) - 7 (E) | TILT switch is not pressed to down | 10 kΩ or higher |
| 4 (OPN) - 7 (E) | SLIDE switch is pressed to open | Below 1 Ω |
| 4 (OPN) - 7 (E) | SLIDE switch is not pressed to open | 10 kΩ or higher |
| 3 (CLS) - 7 (E) | SLIDE switch is pressed to close | Below 1 Ω |
| 3 (CLS) - 7 (E) | SLIDE switch is not pressed to close | 10 kΩ or higher |
OK
NG
Disconnect the W3 ECU connector.
Disconnect the W7 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W3-1 (UP) - W7-6 (UP) | Always | Below 1 Ω |
| W3-2 (DWN) - W7-5 (DWN) | Always | Below 1 Ω |
| W3-6 (OPN) - W7-4 (OPN) | Always | Below 1 Ω |
| W3-7 (CLS) - W7-3 (CLS) | Always | Below 1 Ω |
| W7-6 (UP) - Body ground | Always | 10 kΩ or higher |
| W7-5 (DWN) - Body ground | Always | 10 kΩ or higher |
| W7-3 (CLS) - Body ground | Always | 10 kΩ or higher |
| W7-4 (OPN) - Body ground | Always | 10 kΩ or higher |
| W7-7 (E) - Body ground | Always | Below 1 Ω |
OK
NG