Home › Power Source / Network › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049167 MULTIPLEX COMMUNICATION _0234509 LIN COMMUNICATION SYSTEM U

MULTIPLEX COMMUNICATION  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)


U152763E02
4.76,2.635 5.563,2.635 false 2.333,1.667 2.688,1.667 false 5.563,3.75 5.781,3.927 0.219,0.177 10 false DC 2.458,3.74 2.667,3.917 0.208,0.177 10 false DB 0.646,3.729 0.854,3.906 0.208,0.177 10 false DA 2.104,5.396 2.323,5.573 0.219,0.177 10 false DD 5.521,5.5 5.729,5.677 0.208,0.177 10 false DE 0.656,7.167 0.823,7.344 0.167,0.177 10 false J1 1.875,7.177 2.042,7.354 0.167,0.177 10 false J2 3.521,7.177 3.688,7.354 0.167,0.177 10 false J3 5.458,7.167 5.625,7.344 0.167,0.177 10 false J4 1.875,1.875 2.083,2.052 0.208,0.177 10 false DB 1.885,1.01 2.104,1.188 0.219,0.177 10 false DC 2.219,2.219 2.385,2.396 0.167,0.177 10 false J1 2.208,2 2.375,2.177 0.167,0.177 10 false J2 2.729,1.583 2.896,1.76 0.167,0.177 10 false J3 2.198,1.24 2.365,1.417 0.167,0.177 10 false J4 2.125,2.74 2.333,2.917 0.208,0.177 10 false DA 4.635,1.573 4.854,1.75 0.219,0.177 10 false DD 5.625,2.552 5.833,2.729 0.208,0.177 10 false DE

a.

Disconnect the DA and DB main body ECU (driver side junction block) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
DA-1 (ACC) - Body ground B - Body ground ACC power supply Always 11 to 14 V
DA-1 (IG) - Body ground B - Body ground IG power supply Always 11 to 14 V
DB-21 (GND1) - Body ground B - Body ground Body ground Always Below 1 Ω
DB-21 (GND2) - Body ground B - Body ground Body ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.




CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Power Window Control System [w/ Jam Protection Function])


B443150E01
3.458,0.188 3.76,0.385 0.302,0.198 3.521,0.198 3.75,0.365 0.229,0.167 10 false N2

a.

Disconnect the N2 power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
N2-3 (B) - N2-1 (E) L - W-B Battery power supply Always 11 to 14 V
N2-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.




CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Power Window Control System [w/ Jam Protection Function])


B443151E01
3.396,0.219 3.729,0.438 0.333,0.219 3.448,0.24 3.74,0.406 0.292,0.167 10 false N12

a.

Disconnect the N12 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
N12-2 (B) - N12-1 (GND) G - W-B Battery power supply Always 11 to 14 V
N12-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.




CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Power Window Control System [w/ Jam Protection Function])


B443152E01
3.375,0.208 3.74,0.406 0.365,0.198 3.427,0.219 3.719,0.375 0.292,0.156 10 false M11

a.

Disconnect the M11 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
M11-2 (B) - M11-1 (GND) V - W-B Battery power supply Always 11 to 14 V
M11-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.




CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (w/ Sliding Roof System)


B443153E01
3.427,0.156 3.74,0.365 0.313,0.208 3.469,0.177 3.781,0.375 0.313,0.198 10 false W3

a.

Disconnect the W3 sliding roof drive gear sub-assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
W3-9 (IG) - Body ground SB - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch OFF Below 1 V
W3-10 (B) - Body ground L - Body ground +B power supply Always 11 to 14 V
W3-8 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


B443154E01
3.99,0.125 4.313,0.333 0.323,0.208 6.146,0.135 6.469,0.344 0.323,0.208 4.031,0.135 4.281,0.313 0.25,0.177 10 false J19 6.219,0.156 6.469,0.333 0.25,0.177 10 false z1

a.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Check from the rear of the connector while it is connected to the air conditioning amplifier.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
J19-1 (IG+) - J19-14 (GND) P - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch OFF Below 1 V
J19-21 (B) - J19-14 (GND) BR - W-B Battery power source Always 11 to 14 V
J19-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, the ECU may have a malfunction.




CHECK AIR CONDITIONING CONTROL ASSEMBLY


B443156E01
3.354,0.229 3.771,0.469 0.417,0.24 3.406,0.271 3.76,0.448 0.354,0.177 10 false J127

a.

Disconnect the J127 air conditioning control assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
J127-4 (IG+) - J127-5 (GND) SB - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch OFF Below 1 V
J127-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.