FAIL-SAFE FUNCTION
When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.
The table below shows the effects on each system when communication is impossible. For further details, refer to each system.
| Function | Behavior during CAN Failure | |||
|---|---|---|---|---|
1.
Control Master 2.
System Related |
Vehicle Behavior | Indicator and Buzzer | Diagnostic Trouble Code | |
| Compressor Control/Lock Judgment
(Determines whether compressor is locked.) |
1.
Air conditioning amplifier assembly 2.
ECM |
·
When there is not a periodic malfunction: ·
Performs control with engine speed as 0 rpm. ·
Cannot determine whether compressor is locked. ·
When there is a periodic malfunction, the previous value is maintained. |
Nothing | B1499 |
| Forced Air Recirculation Control
(Performs forced air recirculation when coolant temperature is high.) |
1.
Air conditioning amplifier assembly 2.
ECM |
·
When there is not a periodic malfunction, cannot perform forced air recirculation when coolant temperature is high. ·
When there is a periodic malfunction, the previous value is maintained. |
Nothing | Nothing |
| Coolant Temperature Correction Control/Warm-up Control
(Performs A/C correction based on the engine coolant temperature.) |
1.
Air conditioning amplifier assembly 2.
ECM |
·
When there is not a periodic malfunction: ·
Performs control with engine coolant temperature as 80°C (176°F). ·
Cannot perform warm-up control. ·
When there is a periodic malfunction, the previous value is maintained. |
Nothing | Nothing |
| Vent Control/Automatic FOOT/DEF Control
(Performs vent control according to automatic FOOT/DEF.) |
1.
Air conditioning amplifier assembly 2.
ECM, Combination meter assembly |
·
When there is not a periodic malfunction: ·
Performs control with engine coolant temperature as 80°C (176 °F)(when communication is lost with the ECM). ·
Performs control with vehicle speed as 0 km/h (0 mph) (when communication is lost with the combination meter assembly). ·
Cannot perform automatic FOOT/DEF control ·
When there is a periodic malfunction, the previous value is maintained. |
Nothing | Nothing |
| Engine Model Information Judgment
(Uses the engine model information to determine the engine type.) |
1.
Air conditioning amplifier assembly 2.
ECM |
·
When there is not a periodic malfunction, the default settings are used. ·
When there is a periodic malfunction, the previous value is maintained. |
Nothing | Nothing |
| Ambient Temperature Display
(Sends the ambient temperature data to the combination meter and displays it on the multi-information display.) |
1.
Air conditioning amplifier assembly 2.
Combination meter assembly |
·
When there is not a periodic malfunction, the ambient temperature cannot be displayed. ·
When there is a periodic malfunction, the previous value is maintained. |
Nothing | Nothing |
| Defogger Control
(Performs defogger control.) |
1.
Air conditioning amplifier assembly 2.
Combination meter assembly |
·
When there is not a periodic malfunction, cannot perform defogger control. ·
When there is a periodic malfunction, the previous value is maintained. |
Nothing | Nothing |
| A/C Control/Correction Using Vehicle Speed
(A/C control is performed according to the vehicle speed.) |
1.
Air conditioning amplifier assembly 2.
Combination meter assembly |
·
When there is not a periodic malfunction: ·
Performs control with vehicle speed as 0 km/h (0 mph). ·
Cannot perform correction using vehicle speed. ·
When there is a periodic malfunction, the previous value is maintained. |
Nothing | Nothing |
| Temperature Unit of Measurement
(Determines the unit of measurement for the temperature.) |
1.
Air conditioning amplifier assembly 2.
Combination meter assembly |
·
When there is not a periodic malfunction, the unit of measurement is set to °F. ·
When there is a periodic malfunction, the previous value is maintained. |
Nothing | Nothing |
| Memory Seat
(Memorizes and recalls the seat position.) |
1.
Front power seat control ECU and switch LH 2.
ECM, Main body ECU (driver side junction block assembly), Outer mirror control ECU assembly, Multiplex tilt and telescopic ECU |
·
If communication is lost with the ECM: ·
The position is not recalled when ignition switch is turned to ON. ·
The position cannot be memorized or recalled. ·
If communication is lost with the main body ECU or outer mirror control ECU assembly: The position cannot be memorized or recalled. ·
If communication is lost with the multiplex tilt and telescopic ECU: The tilt position cannot be memorized or recalled. |
Nothing | Nothing |
| 2WD-4WD LOW Switching Limitation and 4WD-4WD LOW Switching Limitation
(When there is a wheel speed signal malfunction, 2WD-4WD LOW and 4WD HIGH-4WD LOW switching are prohibited.) |
1.
4WD control ECU 2.
Brake actuator assembly (skid control ECU) |
2WD-4WD HIGH and 4WD HIGH-4WD LOW switching are prohibited. | 4HI and 4LO indicator light blinks | U0122 |
| High-Low Switching Limitation
(When there is a vehicle speed/automatic transmission signal malfunction, High-Low switching is prohibited.) |
1.
4WD control ECU 2.
ECM, Brake actuator assembly (skid control ECU) |
2WD-4WD HIGH and 4WD HIGH-4WD LOW switching are prohibited. | 4HI and 4LO indicator light blinks | ·
U0100 ·
U0122 |
| Engine ON/OFF Judgment
(Changes control when engine is ON/OFF according to the engine speed.) |
1.
4WD control ECU 2.
ECM |
4WD HIGH-4WD LOW switching are prohibited. | 4HI and 4LO indicator light blinks | U0100 |
| Shift Position Judgment | 1.
4WD control ECU 2.
ECM |
4WD HIGH-4WD LOW switching are prohibited. | 4HI and 4LO indicator light blinks | U0100 |
| Indicator and Buzzer Signal Output
(Outputs a signal indicating the state of the indicators and buzzers, which represents the actuator position and switching status.) |
1.
4WD control ECU 2.
- |
Cannot update the indicator and buzzer signals, as signal cannot be transmitted. | Cannot update the indicator and buzzer signals, as signal cannot be transmitted. | Nothing |
| Electrical Load Control
(Performs idle up according to the electrical load.) |
1.
ECM 2.
Main body ECU (driver side junction block assembly), Air conditioning amplifier assembly |
Idle up according to the electrical load is not performed. | The idling speed changes. | Nothing |
| Air Conditioning-linked Control
(Performs idle up according to the compressor load. Performs air conditioning cut control.) |
1.
ECM 2.
Air conditioning amplifier assembly |
Air conditioning-linked control does not operate. | Air conditioning does not operate. | Nothing |
| Charging Control
(Performs idle up according to charging requests.) |
1.
ECM 2.
Main body ECU (driver side junction block assembly), Air conditioning amplifier assembly |
Idle up according to charging requests is not performed. | Idle up according to charging requests is not performed. | Nothing |
| Integrated Control
(Estimates the driver requested torque based on the accelerator pedal operation and performs torque characteristic control according to driving conditions so that drivability, acceleration performance and acceleration feeling are improved.) |
1.
ECM 2.
Brake actuator assembly (skid control ECU), Steering angle sensor |
Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, drivability, acceleration performance and acceleration feeling are not improved. | Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, drivability, acceleration performance and acceleration feeling are not improved. | Nothing |
| ECT System Indicator
(Displays shift, switch and mode information to the meter.) |
1.
ECM 2.
Main body ECU (driver side junction block assembly) |
Nothing | ECT system indicators do not illuminate. | Nothing |
| AI-SHIFT Control
(Controls the automatic transmission in order to improve engine braking power and acceleration feel.) |
1.
ECM 2.
Brake actuator assembly (skid control ECU), Radio and display receiver assembly, Navigation receiver assembly |
AI-SHIFT control does not operate. | AI-SHIFT control does not operate. | Nothing |
| Coast Downshift/Heater
Requested Upshift Delay (Changes the coast downshift point based on the air conditioning load. Performs heater requested upshift delay.) |
1.
ECM 2.
Air conditioning amplifier assembly |
Coast downshift does not operate. | Coast downshift shock becomes stronger. | Nothing |
| Cruise Control
(Adjusts the engine throttle valve opening amount automatically to control the vehicle.) |
1.
ECM 2.
Brake actuator assembly (skid control ECU), Combination meter assembly |
Cruise control is not performed. | ·
When transmission is lost: The cruise main indicator light does not illuminate. ·
When reception is lost: Cruise control is not performed. |
Nothing |
| Engine Control
(Performs fuel supply analysis and alcohol concentration learning.) |
1.
ECM 2.
Combination meter assembly |
Alcohol concentration learning is not performed. | Drivability worsens and the engine may stall due to the delay of alcohol concentration learning. | U0155 |
| ABS control
(Monitors for tire slippage and performs fluid pressure control to prevent the wheels from locking up in order to maintain vehicle stability and vehicle body deceleration.) |
1.
Brake actuator assembly (skid control ECU) 2.
4WD control ECU |
The ABS does not operate. | ABS warning light turns on. | U0073 |
| MSR control
(Prevents the tires from slipping due to engine drag torque by increasing engine torque.) |
1.
Brake actuator assembly (skid control ECU) 2.
ECM, Steering angle sensor, 4WD control ECU |
MSR does not operate. | Light turns on. | ·
U0073 ·
U0100 ·
U0114 ·
U0123 ·
U0126 |
| TCS control
(Prevents excessive tire slippage due to engine torque by decreasing engine torque and increasing pressure to the brakes.) |
1.
Brake actuator assembly (skid control ECU) 2.
ECM, Steering angle sensor, 4WD control ECU |
TCS does not operate. | Light turns on. | ·
U0073 ·
U0100 ·
U0114 ·
U0123 ·
U0126 |
| VSC control
(Reduces excess yaw by increasing brake pressure, and induces necessary yaw by increasing brake pressure and reducing engine torque.) |
1.
Brake actuator assembly (skid control ECU) 2.
ECM, Steering angle sensor, 4WD control ECU |
VSC does not operate. | Light turns on. | ·
U0073 ·
U0100 ·
U0114 ·
U0123 ·
U0126 |
| Memory Mirror
·
Memorizes and recalls the mirror position. ·
Retracts the mirrors electronically. |
1.
Outer mirror control ECU assembly 2.
ECM, Main body ECU (driver side junction block assembly), Front power seat ECU and switch LH |
·
When communication is lost with the ECM, mirror position memorization cannot be performed. ·
When communication is lost with the main body ECU: Manual and automatic mirror retraction cannot be performed. ·
When communication is lost with the front power seat ECU and switch LH: The position cannot be memorized or recalled. |
Nothing | Nothing |
| Steering sensor
(Detects the steering wheel angle.) |
1.
Steering angle sensor 2.
Brake actuator assembly (skid control ECU) |
Periodically sends STR1S01 (STS0=1) every 12 milliseconds. | Brake warning light turns on. | Nothing |
| Auto away/return control
(Controls the auto away/return operation according to the SKSW and IG signals. Prohibits auto away/return control.) |
1.
Multiplex tilt and telescopic ECU 2.
Main body ECU (driver side junction block assembly), Combination meter assembly, Bus buffer ECU |
The memorization, recall, auto-return and auto-away functions do not operate. | Nothing | ·
B2621 ·
B2624 |
| Memorization/recall control
(Controls the steering wheel position memorization and recall for the seat position memory.) |
1.
Multiplex tilt and telescopic ECU 2.
Front power seat control ECU and switch LH |
Memorization/recall control does not operate. | Nothing | B2621 |
| TC DTC output service
(While TC = ON is being received from the engine, a DTC is output in response to the request from the combination meter assembly.) |
1.
Combination meter assembly 2.
ECM |
If the TC signal is lost during TC service (TC=ON), the TC is determined to be OFF and TC service ends. | Nothing | Nothing |
| Event Data Recorder (12 EDR)
(Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.) |
1.
Center airbag sensor assembly 2.
ECM, Brake actuator assembly (skid control ECU), Steering angle sensor |
·
When reception is lost, an invalid value is recorded in the EDR. ·
When there is a periodic problem, the previous value is maintained. |
Nothing | Nothing |
| Airbag Warning Light Control
(Sends airbag warning light illumination information.) |
1.
Combination meter assembly 2.
Center airbag sensor assembly |
- | Nothing | Nothing |
| Collision Detection Signal
(Notifies the system of a collision in order to perform fuel cut when a vehicle collision occurs.) |
1.
ECM 2.
Center airbag sensor assembly |
- | Nothing | Nothing |
| Seat Belt Warning Control
(Sends information about the passengers in order to turn the seat belt warning on and off.) |
1.
Main body ECU (driver side junction block assembly), Combination meter assembly 2.
Center airbag sensor assembly |
- | Nothing | Nothing |
| Tachometer
(Controls the tachometer according to engine speed signals.) |
1.
Combination meter assembly 2.
ECM |
The tachometer displays 0 rpm. | Nothing | Nothing |
| Speedometer
(Controls the speedometer according to vehicle speed signals.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
The speedometer displays 0 km/h (0 mph). | Nothing | Nothing |
| Engine Coolant Temperature Gauge
(Controls the temperature gauge according to the temperature signals.) |
1.
Combination meter assembly 2.
ECM |
The temperature gauge needle is at the middle of the "C" mark or below. | Nothing | Nothing |
| ODO/TRIP Meter
(Indicates the driven distance in the combination meter according to the vehicle speed pulse signal summation value.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
The calculation stops and the last displayed value remains. | Nothing | Nothing |
| Automatic Transmission Shift Indicator
(Displays shift information according to the shift position signal.) |
1.
Combination meter assembly 2.
ECM |
The automatic transmission shift indicator turns off. | Nothing | Nothing |
| Brake Warning Light
(Turns the brake warning light on and off.) |
1.
Combination meter assembly 2.
Main body ECU (driver side junction block assembly), Brake actuator assembly (skid control ECU) |
The brake warning light illuminates. | The brake warning light illuminates. | Nothing |
| SRS Warning Light
(Turns the SRS warning light on and off.) |
1.
Combination meter assembly 2.
Center airbag sensor assembly |
The SRS warning light illuminates. | The SRS warning light illuminates. | Nothing |
| Driver Side Seat Belt Warning Light
(Turns the driver side seat belt warning light on and off.) |
1.
Combination meter assembly 2.
Main body ECU (driver side junction block assembly) |
The driver side seat belt warning light illuminates. | The driver side seat belt warning light illuminates. | Nothing |
| All Doors Open Light
(Turns the all doors open light on and off.) |
1.
Combination meter assembly 2.
Main body ECU (driver side junction block assembly) |
The all doors open light illuminates. | Nothing | Nothing |
| BEAM Indicator Light
(Turns the BEAM indicator light on and off.) |
1.
Combination meter assembly 2.
Main body ECU (driver side junction block assembly) |
The BEAM indicator condition is maintained. | Nothing | Nothing |
| TAIL Indicator Light
(Turns the TAIL indicator light on and off.) |
1.
Combination meter assembly 2.
Main body ECU (driver side junction block assembly) |
The TAIL indicator condition is maintained. | Nothing | Nothing |
| HEAD Indicator Light
(Turns the HEAD indicator light on and off.) |
1.
Combination meter assembly 2.
Main body ECU (driver side junction block assembly) |
The HEAD indicator condition is maintained. | Nothing | Nothing |
| CRUISE Main Indicator Light
(Turns the CRUISE main indicator light on and off.) |
1.
Combination meter assembly 2.
ECM |
The cruise main indicator condition is maintained. | Nothing | Nothing |
| ABS Warning Light
(Turns the ABS warning light on and off.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
The ABS warning light illuminates. | The ABS warning light illuminates. | Nothing |
| VSC OFF Indicator Light
(Turns the VSC OFF indicator light on and off.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
The VSC OFF indicator condition is maintained. | Nothing | Nothing |
| SLIP Indicator Light
(Turns the SLIP indicator light on and off.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
The slip indicator condition is maintained. | Nothing | Nothing |
| 4LO Warning Light
(Turns the 4LO warning light on and off.) |
1.
Combination meter assembly 2.
4WD control ECU |
The 4LO indicator condition is maintained. | Nothing | Nothing |
| 4HI Warning Light
(Turns the 4HI warning light on and off.) |
1.
Combination meter assembly 2.
4WD control ECU |
The 4HI indicator condition is maintained. | Nothing | Nothing |
| Passenger Side Seat Belt Warning Light
(Turns the passenger side seat belt warning light on and off.) |
1.
Combination meter assembly 2.
Center airbag sensor assembly |
The passenger side seat belt warning light illuminates. | Nothing | Nothing |
| Seat Belt Warning Buzzer
Controls the seat belt warning buzzer to sound and not sound according to the various signals that are input. |
1.
Combination meter assembly 2.
ECM, Main body ECU (driver side junction block assembly), Brake actuator assembly (skid control ECU), Center airbag sensor assembly |
The seat belt warning buzzer condition is maintained. | Nothing | Nothing |
| Key Reminder Buzzer
Controls the key reminder buzzer to sound and not sound according to the various signals that are input. |
1.
Combination meter assembly 2.
Main body ECU (driver side junction block assembly) |
The key reminder buzzer does not sound. | Nothing | Nothing |
| Parking Brake Unreleased Warning Buzzer
Controls the parking brake unreleased warning buzzer to sound and not sound according to the various signals that are input. |
1.
Combination meter assembly 2.
Main body ECU (driver side junction block assembly), Brake actuator assembly (skid control ECU) |
The parking brake unreleased warning buzzer does not sound. | Nothing | Nothing |
| Door Ajar Driving Warning Buzzer
Controls the door ajar driving warning buzzer to sound and not sound according to the various signals that are input. |
1.
Combination meter assembly 2.
Main body ECU (driver side junction block assembly), Brake actuator assembly (skid control ECU) |
The door ajar driving warning buzzer does not sound. | Nothing | Nothing |
| Sequential Shift Reject Buzzer
Controls the sequential shift reject buzzer to sound and not sound according to the various signals that are input. |
1.
Combination meter assembly 2.
ECM |
The sequential shift reject buzzer condition is maintained. | Nothing | Nothing |
| Alarm Control
(Sounds various warnings.) |
1.
Main body ECU (driver side junction block assembly) 2.
ECM, Bus buffer ECU |
·
If communication is lost with the ECM: Alarm cancellation according to the engine speed does not operate. ·
When communication is lost with the bus buffer ECU, warning output does not operate. |
Nothing | ·
U0199 ·
U0208 ·
U1002 ·
U1115 |
| Door Lock Control
(Locks/unlocks the doors.) |
1.
Main body ECU (driver side junction block assembly) 2.
ECM, Combination meter assembly, Center airbag sensor assembly, Bus buffer ECU |
·
If communication is lost with the combination meter assembly: ·
The speed-sensitive automatic door lock function does not operate. ·
The key lock-in prevention unlock function when the vehicle is being driven is permitted. ·
When communication is lost with the ECM: ·
The shift-linked automatic door unlock function does not operate. ·
The shift-linked automatic door unlock switching using the manual switch does not operate. ·
The key lock-in prevention unlock function when the engine is started is permitted. ·
When communication is lost with the center airbag sensor assembly: Key-linked lock control prohibition when the seat belts are fastened is not possible. ·
When communication is lost with the bus buffer ECU: KLEG is maintained. |
Nothing | ·
U0199 ·
U0208 ·
U1002 ·
U1115 |
| Illumination Control
(Performs illumination control.) |
1.
Main body ECU (driver side junction block assembly) 2.
Bus buffer ECU |
KLEG is maintained. | Nothing | ·
U0199 ·
U0208 ·
U1002 ·
U1115 |
| Power Window Control
(Performs key off power window control.) |
1.
Main body ECU (driver side junction block assembly) 2.
Bus buffer ECU |
KLEG is maintained. | Nothing | ·
U0199 ·
U0208 ·
U1002 ·
U1115 |
| Light Control
(Controls the display dimming and daytime running lights.) |
1.
Main body ECU (driver side junction block assembly) 2.
ECM, Combination meter assembly |
·
When communication is lost with the ECM, daytime running light control is not performed. ·
When communication is lost with the combination meter assembly, automatically performs display dimming control when tail mode is not canceled (when the light sensor illuminance signal value is less than the display dimming value, the interior displays and indicators are dimmed). |
Nothing | ·
U0199 ·
U0208 ·
U1002 ·
U1115 |
| Wireless
(Controls the wireless lock/unlock functions.) |
1.
Main body ECU (driver side junction block assembly) 2.
Bus buffer ECU |
KLEG is maintained. | Nothing | ·
U0199 ·
U0208 ·
U1002 ·
U1115 |
| Option Control
(Controls optional wireless lock, answer-back optional illumination, alarm warning requests and dome light warning requests.) |
1.
Main body ECU (driver side junction block assembly) 2.
Bus buffer ECU |
·
Optional wireless lock control does not operate. ·
Answer-back control for optional illumination does not operate. ·
Alarm warning request control does not operate. ·
Dome light warning request control does not operate. |
Nothing | ·
U0199 ·
U0208 ·
U1002 ·
U1115 |
| Lock Control
(Sends a door lock request signal.) |
1.
Bus buffer ECU 2.
Main body ECU (driver side junction block assembly) |
Lock control is not performed. | Nothing | Nothing |
| Air conditioning control
(Requests air conditioning control by sending DFON and ACON signals.) |
1.
Bus buffer ECU 2.
Air conditioning amplifier assembly |
Air conditioning control is not performed. | Nothing | Nothing |
| Hazard answer-back control
(Requests hazard blinking through the HZRD bit.) |
1.
Bus buffer ECU 2.
Main body ECU (driver side junction block assembly) |
Hazard answer-back control is not performed. | Nothing | Nothing |
| Eco Navigation Display
(Displays the average fuel consumption history and a graph indicating the fuel consumption in 1 minute intervals.) |
1.
Radio and display receiver assembly, Navigation receiver assembly 2.
Combination meter assembly |
·
Stops updating the average fuel consumption history on the eco navigation (eco drive screen). ·
If the distance to empty is displayed on the eco navigation (eco drive) screen, the value for the distance to empty is cleared due to a distance to empty communication stop. |
·
The most recent value for the fuel consumption interval graph on the eco navigation (eco drive) screen is cleared. ·
The numbers of the distance to empty displayed on the fuel consumption screen of the eco navigation (eco drive) display are cleared. |
U0155 |
| Destination Determination
(Determines the destination based on the destination symbol and destination package information and selects the display language, time zone, etc.) |
1.
Radio and display receiver assembly, Navigation receiver assembly 2.
Main body ECU (driver side junction block assembly) |
Determines the destination according to the last received value and operates accordingly (if there is no last received value, the system operates using the default value). | The time zone and language selection screens do not match the destination. | U0140 |
| Vehicle Customize Function
(Changes the behavior and control parameters of various functions [illumination lighting time, etc.] according to user operation via the screen.) |
1.
Radio and display receiver assembly, Navigation receiver assembly 2.
Main body ECU (driver side junction block assembly), Front power seat ECU and switch LH, Multiplex tilt and telescopic ECU |
3 retries are performed (including the first time). | ·
The customize options for items related to the main body ECU are not displayed or the setting cannot be changed. ·
The customize options for items related to the front power seat ECU and switch LH are not displayed or the setting cannot be changed. ·
The customize options for items related to the multiplex tilt and telescopic ECU are not displayed or the setting cannot be changed. |
·
B15F6 ·
B15F8 |
| ESPO
(Displays the level of "eco" driving.) |
1.
Radio and display receiver assembly, Navigation receiver assembly 2.
Center airbag sensor assembly, Air conditioning amplifier assembly, Main body ECU (driver side junction block assembly), Steering angle sensor |
Nothing | Nothing | Nothing |
| Charging Station Reporting Service
(Informs the user about charging stations within range from distance to empty based on information received from the G-BOOK center.) |
1.
Radio and display receiver assembly, Navigation receiver assembly 2.
Combination meter assembly |
Stops providing information and resets values to the default. | Cannot provide information. | Nothing |
| Meter-linked Function
(Changes display based on customization information set through the meter. Outputs the customization information set in the system.) |
1.
Radio and display receiver assembly, Navigation receiver assembly 2.
Combination meter assembly |
Maintains the last valid state. | Nothing | Nothing |
| Blind Spot Monitor
(Warns the driver when the system detects a vehicle in the blind spots of the outer mirrors.) |
1.
Blind spot monitor sensor RH/LH 2.
ECM, Brake actuator assembly (skid control ECU), Main body ECU (driver side junction block assembly), Steering angle sensor, Blind spot monitor sensor RH/LH |
Nothing | Blind spot monitor system warning displayed. | ·
U0100 ·
U0126 ·
U0129 ·
U0142 ·
U0232 |
| Relay Function
(Transmits relay frames and does not transmit non-relay frames.) |
1.
Network gateway ECU 2.
ECUs connected to V bus and V2 bus |
CAN controller is reset. | Nothing | Nothing |
| Diagnostic Function
(Determines the connection and communication status of ECUs which are connected to the V2 bus.) |
1.
Network gateway ECU 2.
ECUs connected to V2 bus |
CAN controller is reset. | Nothing | ·
U0233 ·
U1002 |
| NM Function
(Performs communication via NM frames with ECUs that are equipped with NM, and controls the CAN communication sleep/wake up functions.) |
1.
Network gateway ECU 2.
ECUs with NM functions connected to V bus and V2 bus |
·
CAN controller is reset. ·
Enter LimpHome mode. |
Nothing | Nothing |
| CCP Function
(Communicates with tools connected via the V bus and monitors the RAM in the gateway ECU.) |
1.
Network gateway ECU 2.
Tools connected via V bus |
CAN controller is reset. | Nothing | Nothing |
| Calculates the operation condition using the following information
·
Vehicle speed information ·
Brake pressure information |
1.
Brake control with bracket relay 2.
ECM, Brake actuator assembly (skid control ECU) |
Maintains the last valid information from before communication stopped. | Warning displayed on multi-information display. | ·
U0101 ·
U0129 |
| Calculates the wheel slip condition using the following information
·
Vehicle speed information ·
Brake pressure information |
1.
Brake control with bracket relay 2.
ECM, Brake actuator assembly (skid control ECU) |
Maintains the last valid information from before communication stopped. | Warning displayed on multi-information display. | ·
U0101 ·
U0129 |
| Calculates the vehicle acceleration condition using the following information
·
Vehicle speed information ·
Brake pressure information |
1.
Brake control with bracket relay 2.
ECM, Brake actuator assembly (skid control ECU) |
Maintains the last valid information from before communication stopped. | Warning displayed on multi-information display. | ·
U0101 ·
U0129 |
| Calculates the wheel condition using the following information
·
Vehicle speed information ·
Brake pressure information |
1.
Brake control with bracket relay 2.
ECM, Brake actuator assembly (skid control ECU) |
Maintains the last valid information from before communication stopped. | Warning displayed on multi-information display. | ·
U0101 ·
U0129 |
| Calculates the vehicle direction of travel using the following information
·
Vehicle speed information ·
Brake pressure information |
1.
Brake control with bracket relay 2.
ECM, Brake actuator assembly (skid control ECU) |
Maintains the last valid information from before communication stopped. | Warning displayed on multi-information display. | ·
U0101 ·
U0129 |
| Informs the driver of a system malfunction | 1.
Brake control with bracket relay 2.
Combination meter assembly |
Does not illuminate. | Warning displayed on multi-information display. | U0155 |