Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET(for Bank 1) › from 2016.08
RM27M0U _51 Engine / Hybrid System _049106 3UR-FE ENGINE MECHANICAL _0234021 CYLINDER HEAD GASKET(for Bank 1) A

3UR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET(for Bank 1)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly LH (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY LH

Hide 11116 3.INSTALL CYLINDER HEAD GASKET LH

a.

Check the piston protrusions for each cylinder.

i.

Clean the cylinder block with solvent.


ii.

Set the piston of the cylinder to be measured to slightly ATDC.



b.
A380008E01
2.292,1.823 2.469,1.823 2.469,1.823 3.073,1.052 true 1.573,0.281 2.344,0.479 0.771,0.198 10 false Front 1.823,1.719 2.594,1.917 0.771,0.198 10 false Lot No.

Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

NOTICE:
·

Be careful of the installation direction.

·

Make sure that no oil is on the front end (indicated by the arrows) of the cylinder head gasket.




Hide 11101 4.INSTALL CYLINDER HEAD SUB-ASSEMBLY LH

HINT:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly LH (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.

Place the cylinder head on the cylinder block.

NOTICE:
·

Ensure that no oil is on the mounting surface of the cylinder head.

·

Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.



HINT:

The cylinder head bolts are tightened in 3 progressive steps.



b.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


c.
A160737E13
1.635,0.281 1.74,0.458 0.104,0.177 10 true 1 1.635,1.802 1.74,1.979 0.104,0.177 10 true 2 1.094,0.281 1.198,0.458 0.104,0.177 10 true 3 2.198,1.802 2.302,1.979 0.104,0.177 10 true 4 2.188,0.271 2.292,0.448 0.104,0.177 10 true 5 1.063,1.802 1.167,1.979 0.104,0.177 10 true 6 0.51,1.813 0.615,1.99 0.104,0.177 10 false 7 2.729,0.271 2.833,0.448 0.104,0.177 10 false 8 2.771,1.802 2.875,1.979 0.104,0.177 10 true 9 0.469,0.271 0.656,0.448 0.188,0.177 10 true 10

Step 1:

i.

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts with the plate washers in several steps, in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)



d.
A132162E01
0.04,1.271 0.408,1.446 0.369,0.174 10 Front 0.704,1.638 1.619,1.812 0.915,0.174 10 Painted Mark 1.552,1.168 1.208,1.627 false 0.922,0.378 1.198,0.543 0.276,0.165 10 90° 2.687,0.366 2.963,0.531 0.276,0.165 10 90°

Step 2:

i.

Mark each cylinder head bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head bolts another 90° in the sequence shown in step 1.



e.

Step 3:

i.

Tighten the cylinder head bolts an additional 90° in the sequence shown in step 1.


ii.

Check that the painted marks are now facing rearward.



f.
A160736E12
3.219,0.615 3.313,0.813 0.094,0.198 10 true 1 2.948,0 3.042,0.198 0.094,0.198 10 true 2

Install and uniformly tighten the 2 bolts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13716 5.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem caps.


b.

Install the 16 valve stem caps to the cylinder head.


Hide 13750 6.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

b.

Install the 16 lash adjusters to the cylinder head.

NOTICE:

Install the lash adjuster at the same place it was removed from.



Hide 13801 7.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply engine oil to the lash adjuster tips and valve stem cap ends.


b.
A386787E01
0.74,1.042 0.823,1.042 0.823,1.042 1.031,1.094 false 2.094,0.188 1.865,0.188 1.865,0.188 1.615,0.396 false 2.458,1.125 2.667,1.125 true 2.146,0.094 3.365,0.281 1.219,0.188 10 false Valve Rocker Arm 2.708,1.031 3.417,1.385 0.708,0.354 10 false Valve Lash Adjuster 0.01,0.948 0.771,1.344 0.76,0.396 10 false Valve Stem Cap

Install the 16 valve rocker arms as shown in the illustration.


Hide 8.INSTALL CAMSHAFTS (for Bank 1)

Hide 17105 9.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.

Install the exhaust manifold LH (see page Engine / Hybrid System>3UR-FE EXHAUST>EXHAUST MANIFOLD>INSTALLATION).