Home › Engine / Hybrid System › 3UR-FE EXHAUST › EXHAUST MANIFOLD
RM27M0U _51 Engine / Hybrid System _049109 3UR-FE EXHAUST _0234046 EXHAUST MANIFOLD A

3UR-FE EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

If an exhaust gas leak has been repaired, perform an inspection following the repair (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 17104 1.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A162117E02
3.063,2.375 3.271,2.375 3.271,2.375 3.271,1.438 false 1.188,2.219 1.198,2.104 1.198,2.104 1.094,2.104 false 2.823,2.292 3.083,2.448 0.26,0.156 10 false Tab 0.76,2.021 1.104,2.188 0.344,0.167 10 false Claw

Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.

HINT:
·

Install the exhaust manifold gasket with the gasket tab facing toward the front of the engine.

·

Install the air tube gasket with the gasket's claws facing the tube side.




b.
A162754E01
0.655,0.296 0.783,0.442 0.128,0.145 10 A 0.517,0.913 0.646,1.058 0.128,0.145 10 A

Temporarily install the exhaust manifold and then uniformly tighten 8 new nuts that are not labeled A. Then tighten the new nuts labeled A in the illustration.

Torque:
for nut A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except nut A : 21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17167 2.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A162752

Install the heat insulator with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17105 3.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A162119E02
2.667,0.625 2.792,0.625 2.792,0.625 2.792,1.104 false 1.823,2.24 2.208,2.24 false 2.344,0.542 2.667,0.729 0.323,0.188 10 true Tab 2.229,2.146 2.573,2.302 0.344,0.156 10 false Claw

Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.

HINT:
·

Install the exhaust manifold gasket with the gasket tab facing toward the rear of the engine.

·

Install the air tube gasket with the gasket's claws facing the tube side.




b.
A162115E01
2.783,0.098 2.906,0.261 0.123,0.163 10 A 3.069,0.862 3.192,1.025 0.123,0.162 10 A

Temporarily install the exhaust manifold and then uniformly tighten 8 new nuts that are not labeled A. Then tighten the new nuts labeled A in the illustration.

Torque:
for nut A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except nut A : 21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17168 4.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A162114

Install the heat insulator with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 45203 5.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
U151575E02
1.375,1.406 0.948,1.719 0.948,1.719 1.771,1.583 false 0.552,1.75 1.281,1.896 0.729,0.146 10 false Matchmark

Align the matchmarks and insert the No. 2 intermediate shaft into the intermediate shaft.


b.
U151576E02
1.646,1.354 1.104,1.667 1.104,1.667 1.688,1.667 false 0.344,1.604 1.063,1.813 0.719,0.208 10 true Matchmark

Align the matchmarks and insert the No. 2 intermediate shaft into the power steering gear.


c.

Install the 2 bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 17410 6.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 37140 7.INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

Hide 88320 8.CONNECT COOLER COMPRESSOR ASSEMBLY

Hide 11452 11.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16572 14.CONNECT OUTLET RADIATOR HOSE

Hide 16571 15.CONNECT INLET RADIATOR HOSE

Hide 17880 17.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 21.INSPECT FOR EXHAUST GAS LEAK

HINT:

If an exhaust gas leak has been repaired, perform an inspection following the repair (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

Hide 53739A 22.INSTALL FRONT FENDER APRON SEAL REAR LH

a.

Install the fender apron seal with the 5 clips.


Hide 53737B 23.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the fender apron seal with the 6 clips.


Hide 53736A 24.INSTALL FRONT FENDER APRON SEAL REAR RH

a.

Install the fender apron seal with the 5 clips.


Hide 53736 25.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the fender apron seal with the 6 clips.


Hide 11209 27.INSTALL V-BANK COVER SUB-ASSEMBLY