Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.08
RM27M0U _52 Drivetrain _049125 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0234142 AUTOMATIC TRANSMISSION SYSTEM C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The ECM detects the signal from the transfer indicator switch.

This DTC indicates that the transfer indicator switch (L4) remains on.

DTC Code DTC Detection Condition Trouble Area
P2772 Transfer indicator switch (L4) remains on while the vehicle is being driven under the following conditions for 1.8 sec. or more (1-trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer position switch is in 2WD or 4H.
·

Short in transfer indicator switch (L4) circuit

·

4 wheel drive control ECU

·

ECM



MONITOR DESCRIPTION

The ECM monitors the transfer-case transfer indicator switch to determine when the transfer-case 4L gears are engaged. If the transfer-case 4L gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the transfer indicator switch, illuminate the MIL and store the DTC:

·

The transfer indicator switch indicates that the 4L transfer-case gears are engaged.

·

The transfer-case shifter is in the "2WD" or "4H" position.

·

The transfer-case output shaft speed is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


MONITOR STRATEGY

Related DTCs P2772: Transfer indicator switch/Rationality fault diagnostics
Required sensors/Components Transfer indicator switch
Frequency of operation Continuous
Duration ON malfunction (A): 1.8 seconds
ON malfunction (B): 0.5 seconds
MIL operation 1 driving cycle
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present P0500 (Output speed sensor circuit)
P0722 (Vehicle speed sensor circuit)
Transfer neutral position switch OFF

ON Malfunction (A)
Output speed (Transfer output speed) 1000 rpm or more, and less than 3000 rpm

ON Malfunction (B)
Output speed (Transfer output speed) 143 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: ON malfunction (A) and (B)

ON Malfunction (A)
Transfer indicator switch (L4) ON

ON Malfunction (B)
Actual transfer gear ratio
Transfer input speed/Transfer output speed
0.9 or more, and less than 1.1

WIRING DIAGRAM

C292708E02
1.289,1.906 1.714,2.108 0.425,0.202 10 D70 1.289,2.093 2.871,2.295 1.582,0.202 10 Transfer Indicator Switch 1.289,2.557 2.580,2.759 1.290,0.202 10 Transfer Assembly 2.702,0.819 3.127,1.021 0.425,0.202 10 L4 2.403,3.58 2.828,3.782 0.425,0.202 10 L4 2.679,1.294 3.104,1.496 0.425,0.202 10 H4 2.382,3.232 2.807,3.434 0.425,0.202 10 H4 2.984,1.529 3.408,1.731 0.425,0.202 10 1 2.984,1.044 3.408,1.246 0.425,0.202 10 2 5.603,0.927 6.028,1.129 0.425,0.202 10 L4 1.051,3.989 1.475,4.191 0.425,0.202 10 A26 2.691,3.369 3.116,3.571 0.425,0.202 10 12 2.691,3.719 3.116,3.921 0.425,0.202 10 13 1.051,4.175 3.600,4.377 2.550,0.202 10 4 Wheel Drive Control ECU 5.8,3.989 6.225,4.191 0.425,0.202 10 A24 5.8,4.175 6.281,4.377 0.480,0.202 10 ECM 5.342,1.044 5.767,1.246 0.425,0.202 10 21

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.CHECK TRANSFER INDICATOR SWITCH
a.
U152644E03
1.719,1.146 2.531,1.698 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.563,1.604 2.875,1.802 0.313,0.198 10 false L4 0.344,1.01 0.719,1.24 0.375,0.229 10 false D70

Disconnect the D70 transfer indicator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D70-2 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Transfer Indicator Switch)



OK

NG

2.CHECK 4 WHEEL DRIVE CONTROL ECU
2.CHECK 4 WHEEL DRIVE CONTROL ECU
a.
U152643E03
1.844,1.271 2.5,1.729 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.552,1.677 2.865,1.875 0.313,0.198 10 false L4 0.354,1 0.729,1.229 0.375,0.229 10 false A26

Disconnect the D70 transfer indicator switch connector.


b.

Disconnect the A26 4 wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-13 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)



OK

NG

3.CHECK ECM
3.CHECK ECM
a.
U152406E03
1.365,1.792 1.646,0.979 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.625,0.271 2,0.5 0.375,0.229 10 false A24 1.083,1.802 1.667,2 0.583,0.198 10 false 21 (L4)

Disconnect the D70 transfer indicator switch connector.


b.

Disconnect the A26 4 wheel drive control ECU connector.


c.

Disconnect the A24 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-21 (L4) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for 3UR-FE) A
OK (for 3UR-FBE) B
NG C

Text in Illustration
*a Front view of wire harness connector
(to ECM)



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - 4 WHEEL DRIVE CONTROL ECU, TRANSFER INDICATOR SWITCH)