Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL TANK › from 2016.08
RM27M0U _51 Engine / Hybrid System _049097 3UR-FE FUEL _0233962 FUEL TANK A

3UR-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 28800 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 77310A 4.REMOVE FUEL TANK CAP

Hide 77606 5.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)

a.

for 100 L (26.4 US gal) Fuel Tank:

i.

Remove the 2 bolts, 2 nuts and No. 1 fuel tank protector sub-assembly.



b.
A330902

for 144 L (38 US gal) Fuel Tank:

i.

Remove the 6 nuts and No. 1 fuel tank protector sub-assembly.



Hide 77209D 6.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A159750E04
2.458,3.948 2.458,4.135 false 0.615,4.104 0.615,4.292 false 1.052,3.052 1.146,3.052 false 0.26,3.552 0.083,2.958 0.083,2.958 0.208,2.958 false 0.677,3.438 1.063,3.052 true 1.083,3.854 1.229,4.177 true 1.229,4.188 1.323,3.854 true 2.365,4.167 2.563,4.344 0.198,0.177 10 false *5 1.115,4.229 1.302,4.417 0.188,0.188 10 false *4 0.5,4.323 0.719,4.521 0.219,0.198 10 false *3 1.167,2.969 1.396,3.188 0.229,0.219 10 false *2 2.448,2.188 2.698,2.406 0.25,0.219 10 false *a 0.229,2.875 0.427,3.052 0.198,0.177 10 false *1

for 100 L (26.4 US gal) Fuel Tank:

i.

Detach the lock claw by lifting up the cover as shown in the illustration.

Text in Illustration
*1 Pipe
*2 Retainer
*3 Connector
*4 O-Ring
*5 Nylon Tube
*a Lifting Up


ii.

Pinch and pull the main tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





b.
A330904E04
0.979,0.24 0.917,0.24 false 0.917,0.24 0.771,0.51 true 0.375,1.365 0.542,1.365 0.542,1.365 0.771,1.115 true 0.469,1.115 0.469,1.365 true 1.01,0.146 1.323,0.344 0.313,0.198 10 true *1 0.135,1.281 0.323,1.531 0.188,0.25 10 true *2 2.552,0.24 2.802,0.417 0.25,0.177 10 false *a

for 144 L (38 US gal) Fuel Tank:

i.

Pull the tabs of the retainer and pull up as shown in the illustration.

Text in Illustration
*1 Retainer
*2 Tab
*a Pull Up


ii.

Pull the main tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





Hide 77204A 7.DISCONNECT FUEL TANK RETURN TUBE

a.
A152240E04
2.458,3.948 2.458,4.135 false 0.625,4.115 0.625,4.302 false 1.073,3.063 1.156,3.063 false 0.271,3.552 0.094,2.958 0.094,2.958 0.219,2.958 false 0.677,3.427 1.073,3.063 true 1.083,3.854 1.219,4.177 true 1.229,4.188 1.323,3.854 true 2.375,4.146 2.573,4.323 0.198,0.177 10 false *5 1.146,4.24 1.333,4.427 0.188,0.188 10 false *4 0.542,4.323 0.76,4.521 0.219,0.198 10 false *3 1.177,2.979 1.406,3.198 0.229,0.219 10 false *2 2.469,2.188 2.719,2.406 0.25,0.219 10 false *a 0.24,2.875 0.438,3.052 0.198,0.177 10 false *1

for 100 L (26.4 US gal) Fuel Tank:

i.

Detach the lock claw by lifting up the cover as shown in the illustration.

Text in Illustration
*1 Pipe
*2 Retainer
*3 Connector
*4 O-Ring
*5 Nylon Tube
*a Lifting Up


ii.

Pinch and pull the return tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





b.
A330903E02
0.854,2.219 1.323,2.438 1.323,2.438 1.323,2.896 false 0.792,2.75 0.792,2.969 0.792,2.969 0.469,2.969 false 0.469,2.75 0.469,3.021 false 0.385,3.042 0.667,3.208 0.281,0.167 10 false *2 1.229,2.917 1.542,3.094 0.313,0.177 10 false *1 2.563,1.865 2.823,2.083 0.26,0.219 10 false *a

for 144 L (38 US gal) Fuel Tank:

i.

Pull the tabs of the retainer and pull up as shown in the illustration.


ii.

Pull the return tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Tab
*a Pull Up



Hide 8.DISCONNECT VENT LINE HOSE

a.
A152244E03
1.979,0.177 2.167,0.396 0.188,0.219 10 false *a

Pull up the retainer and disconnect the vent line hose.

NOTICE:
·

Do not use any tools in this procedure.


·

Check for any dirt and foreign matter contamination in the valve and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the valve and connector.



Text in Illustration
*a Up


Hide 9.DISCONNECT WIRE HARNESS

a.
A152242

Detach the harness clamp from the fuel tank assembly.


Hide 77213B 10.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A152252E05
2.479,3.958 2.479,4.146 false 0.615,4.104 0.615,4.292 false 1.052,3.063 1.146,3.063 false 0.271,3.531 0.094,2.979 0.094,2.979 0.219,2.979 false 0.688,3.417 1.063,3.094 false 1.083,3.865 1.229,4.188 false 1.229,4.177 1.323,3.844 false 2.365,4.167 2.563,4.344 0.198,0.177 10 false *5 1.115,4.198 1.302,4.385 0.188,0.188 10 false *4 0.5,4.323 0.719,4.521 0.219,0.198 10 false *3 1.167,2.969 1.396,3.188 0.229,0.219 10 false *2 2.917,0.313 3.167,0.531 0.25,0.219 10 false *a 0.229,2.875 0.427,3.052 0.198,0.177 10 false *1

Detach the lock claw by lifting up the cover as shown in the illustration.

Text in Illustration
*1 Pipe
*2 Retainer
*3 Connector
*4 O-Ring
*5 Nylon Tube
*a Lifting Up


b.

Disconnect the fuel tank breather tube from the inlet fuel tank pipe sub-assembly.


c.

Disconnect the fuel tank to filler pipe hose from the inlet fuel tank pipe sub-assembly.


d.

Detach the filler pipe hose and fuel tank breather tube from the No. 1 breather tube clamp.


Hide 77754 11.DISCONNECT OUTLET NO. 1 CANISTER HOSE

a.

Disconnect the outlet No. 1 canister hose from the inlet fuel tank pipe sub-assembly.


b.

Detach the hose from the No. 1 breather tube clamp.


Hide 77100 12.REMOVE FUEL TANK ASSEMBLY

a.

Set an engine lifter underneath the fuel tank assembly.


b.
A152248

for 100 L (26.4 US gal) Fuel Tank:

i.

Remove the 2 bolts, 2 clips, 2 pins, No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly.



c.
A330905

for 144 L (38 US gal) Fuel Tank:

i.

Remove the 3 bolts, 3 clips, 3 pins, 2 No. 1 fuel tank band sub-assemblies and No. 2 fuel tank band sub-assembly.



d.

Slowly lower the engine lifter slightly.

NOTICE:

Be careful not to cut the wiring.



e.
A307675

w/ Cover:

Detach the 3 claws and remove the No. 2 fuel tank protector.


f.
A152243

Detach the wire harness clamp from the fuel tank assembly as shown in the illustration.


g.

Disconnect the fuel pump connector and lower the engine lifter.

NOTICE:
·

Before this procedure, check the connector for dirt, mud or other contamination.

·

Do not use any tools in this procedure.




Hide 77201 13.REMOVE INLET FUEL TANK PIPE SUB-ASSEMBLY

a.
A156396

Remove the 2 nuts and inlet fuel tank pipe sub-assembly.


Hide 77697 14.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
A152249E03
2.809,2.33 3.032,2.540 0.223,0.210 10 *1 2.935,1.603 2.935,2.325 false

for 100 L (26.4 US gal) Fuel Tank:

i.

Remove the nut from the No. 1 fuel tank heat insulator.

Text in Illustration
*1 Nut


ii.

Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.



b.
A330911E02
2.979,0.688 2.781,0.688 2.781,0.688 2.333,1.76 false 2.781,1.531 2.781,0.688 false 3.021,0.604 3.323,0.781 0.302,0.177 10 false *1

for 144 L (38 US gal) Fuel Tank:

i.

Remove the 2 nuts from the No. 1 fuel tank heat insulator.

Text in Illustration
*1 Nut


ii.

Using needle-nose pliers, remove the 2 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.



Hide 77697A 15.REMOVE NO. 2 FUEL TANK HEAT INSULATOR (for 144 L (38 US gal) Fuel Tank)

a.
A330912

Using needle-nose pliers, remove the 3 clips shown in the illustration and then remove the No. 2 fuel tank heat insulator.


Hide 77213B 16.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A152251

Remove the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77020A 17.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A152246C01
0.531,0.646 0.948,0.229 true 1.99,3.031 2.167,2.615 2.167,2.615 2.406,2.615 true 1.938,3.927 2.521,3.927 true 0.76,2.927 0.99,2.927 0.99,2.927 1.24,3.417 true 0.771,2.625 1,2.625 1,2.625 1.438,3.063 true 1.052,4.104 1.052,3.688 1.052,3.688 1.458,3.688 true 1.052,3.833 1.49,3.833 true 2.448,2.49 2.76,2.646 0.313,0.156 10 false *1 0.604,2.521 0.917,2.677 0.313,0.156 10 false *2 0.594,2.833 0.906,2.99 0.313,0.156 10 false *3 2.552,3.823 2.865,3.979 0.313,0.156 10 false *4 0.979,4.167 1.292,4.323 0.313,0.156 10 false *5
*1 Fuel Tank Tube
*2 Tube Joint
*3 Tube Joint Clip
*4 Fuel Suction Plate
*5 O-Ring


Remove the 2 tube joint clips and pull out the fuel tank main tube sub-assembly and fuel tank return tube.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tank tubes.




b.
A390960C01
0.771,1.208 0.771,0.792 true 0.448,1.188 1.281,1.188 1.281,1.188 1.281,0.938 true 0.26,1.073 0.573,1.229 0.313,0.156 10 false *a 0.708,1.323 0.833,1.5 0.125,0.177 10 true . 2.625,0.635 2.75,0.813 0.125,0.177 10 true .
*a Co-rotation Prevention Check Mark


Apply a co-rotation prevention check mark to the fuel suction with pump and gauge tube assembly and fuel tank assembly.

NOTICE:
·

The fuel tank assembly cutout is attached to the protrusion on the fuel tank vent tube assembly.

·

If the fuel suction with pump and gauge tube assembly and fuel tank assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel suction with pump and gauge tube assembly will co-rotate and result in the fuel suction with pump and gauge tube assembly being damaged.

·

Make sure to apply a co-rotation prevention check mark to prevent the fuel suction with pump and gauge tube assembly from co-rotating.




c.
A390961C01
1.229,2.885 1.427,2.885 1.427,2.885 1.625,2.573 true 0.646,0.302 0.833,0.302 0.833,0.302 0.896,0.51 true 1.313,0.771 1.479,0.646 1.479,0.646 1.635,0.646 true 1.979,2.365 2.135,2.094 2.135,2.094 2.292,2.094 true 1,1.99 1.188,1.99 1.188,1.99 1.656,2.49 true 1.063,4.604 1.26,4.604 1.26,4.604 1.646,4.26 true 2.344,1.979 2.656,2.135 0.313,0.156 10 false *1 0.479,0.177 0.792,0.333 0.313,0.156 10 false *a 1.052,2.792 1.365,2.948 0.313,0.156 10 false *b 0.833,1.875 1.146,2.031 0.313,0.156 10 false *c 0.875,4.49 1.188,4.646 0.313,0.156 10 false *d 1.688,0.542 2,0.698 0.313,0.156 10 false *1
*1 Fuel Pump Gauge Retainer
*a SST (claw set)
*b Rib
*c Cutout
*d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer)


Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.

·

Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.




d.
A390962C01
0.677,2.031 0.906,2.031 0.906,2.031 1.094,1.823 true 2.104,1.313 2.25,1.094 2.25,1.094 2.438,1.094 true 0.708,0.74 0.938,0.74 0.938,0.74 1.354,1.021 true 2.49,0.979 2.802,1.135 0.313,0.156 10 false *1 0.531,0.635 0.844,0.792 0.313,0.156 10 false *a 0.5,1.938 0.813,2.094 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Press
V100136

SST (Bolt)


While firmly pressing the claw of SST into rib of the fuel pump gauge retainer, tighten the bolt.


e.
A390959C01
0.76,0.125 0.958,0.125 0.958,0.125 1.24,0.281 true 2.802,1.583 2.802,1.406 2.802,1.406 2.646,1.198 true 0.563,0.031 0.875,0.188 0.313,0.156 10 false *a 2.74,1.594 3.052,1.75 0.313,0.156 10 true *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).


f.
A387317C02
0.615,1.198 0.854,1.198 0.854,1.198 1.333,0.906 true 1.74,1.083 2.573,1.083 true 2.604,1 2.917,1.198 0.313,0.198 10 true *a 0.427,1.094 0.74,1.25 0.313,0.156 10 false *b
*a Center of Fuel Pump Gauge Retainer
*b SST (Plate)


Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.


g.
A391923C01
0.917,0.677 1.115,0.677 1.115,0.677 1.313,0.99 false 0.656,2.542 1.052,2.542 false 1.927,0.802 2.208,0.583 2.208,0.583 2.427,0.583 false 1.781,1.146 1.99,1.594 1.99,1.594 2.25,1.594 true 0.771,2.125 0.969,2.125 0.969,2.125 1.375,2.385 false 0.75,0.583 1.063,0.74 0.313,0.156 10 false *1 0.479,2.448 0.813,2.604 0.333,0.156 10 false *a 2.458,0.479 2.771,0.635 0.313,0.156 10 false *b 0.583,2.021 0.896,2.177 0.313,0.156 10 false *c 2.281,1.5 2.594,1.656 0.313,0.156 10 false *d
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
*d Rib
V100135

Press


While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).


h.

Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


i.
A387343C01
3.177,1.125 3.073,0.906 true 0.625,1.521 0.99,1.521 true 1.281,0.604 1.5,0.365 1.5,0.365 1.708,0.365 true 0.458,1.417 0.771,1.573 0.313,0.156 10 false *a 1.74,0.24 2.052,0.396 0.313,0.156 10 false *b 3.156,1.135 3.406,1.354 0.25,0.219 10 false *c
*a SST (Plate)
*b SST (Handle)
*c SST (Claw Set)
V100135

Loosen


Slowly loosen the fuel pump gauge retainer by approximately 90°.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel tank vent tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.




j.

While one person slowly loosens the fuel pump gauge retainer, have another person press down the rising fuel suction with pump and gauge tube assembly, securely attach the protrusion of the fuel suction with pump and gauge tube assembly to the groove of the fuel tank assembly, and then remove the fuel pump gauge retainer while making sure that the fuel suction with pump and gauge tube assembly is properly aligned.

A390966C01
0.281,1.885 0.479,1.885 0.479,1.885 0.854,1.219 true 2.594,2.177 2.594,1.76 2.594,1.76 2.885,1.76 true 2.594,1.865 3.25,1.865 true 1.125,0.573 1.281,0.146 1.281,0.146 1.031,0.146 true 0.115,1.771 0.427,1.927 0.313,0.156 10 false *a 0.844,0.052 1.156,0.208 0.313,0.156 10 false *b 1.021,1.844 1.333,2 0.313,0.156 10 false *c 1.948,0.302 2.26,0.458 0.313,0.156 10 false *d 2.521,2.198 2.833,2.354 0.313,0.156 10 false *e 5.625,1.74 5.938,1.896 0.313,0.156 10 false *c 6.563,0.156 6.875,0.313 0.313,0.156 10 false *d
*a SST (Plate) *b SST (Handle)
*c Person in Charge of Loosening *d Person in Charge of Supporting
*e Co-rotation Prevention Check Mark - -


NOTICE:
·

The fuel suction with pump and gauge tube assembly is equipped with a spring that pushes against the bottom of the fuel tank assembly to constantly lift the fuel suction with pump and gauge tube assembly upwards.

·

If the fuel suction with pump and gauge tube assembly and fuel tank assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel suction with pump and gauge tube assembly will co-rotate and result in the fuel suction with pump and gauge tube assembly and fuel tank assembly being damaged.

·

Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.

·

Do not bend the arm of the fuel sender gauge assembly.




k.

Remove the gasket from the fuel tank assembly.


Hide 77641A 18.REMOVE NO. 1 FUEL TANK PROTECTOR (w/ Cover)

A307676

HINT:

Only perform this procedure when replacement of the No. 1 fuel tank protector is necessary.


a.

Detach the 4 clamps to remove the No. 1 fuel tank protector.