77641A
1.INSTALL NO. 1 FUEL TANK PROTECTOR (w/ Cover)
Only perform this procedure when replacement of the No. 1 fuel tank protector is necessary.
Attach the 4 clamps to install a new No. 1 fuel tank protector.
77020A
2.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
Apply a light coat of gasoline to a new gasket, and install it to the fuel tank assembly.
Align the protrusion of the pump and gauge tube with the groove of the fuel tank assembly.
| *a | Protrusion |
| *b | Groove |
Install the fuel suction with pump and gauge tube into the fuel tank assembly.
Be careful not to bend the arm of the fuel sender gauge.
| *a | Co-rotation Prevention Check Mark |
Apply a co-rotation prevention check mark to the fuel suction with pump and gauge tube assembly.
Perform this procedure when replacement of the fuel suction with pump and gauge tube assembly is necessary.
| *a | Rotational Start Point Mark (Fuel Tank Assembly Side) |
| *b | Rotational Start Point Mark (Fuel Pump Gauge Retainer Side) |
Temporarily place the fuel pump gauge retainer by aligning the rotational start point mark of a new fuel pump gauge retainer with the rotational start point mark of the fuel tank assembly while pressing the fuel suction with pump and gauge tube into the fuel tank assembly.
| *1 | Fuel Pump Gauge Retainer |
| *a | SST (claw set) |
| *b | Rib |
| *c | Cutout |
| *d | SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer) |
Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.
Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.
Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.
| *1 | Fuel Pump Gauge Retainer |
| *a | SST (Claw Set) |
| *b | Hook |
|
Press |
|
SST (Bolt) |
While firmly pressing the claw of SST into rib of the fuel pump gauge retainer, tighten the bolt.
| *a | SST (Plate) |
| *b | SST (Claw Set) |
|
SST (Bolt) |
Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).
| *a | Center of Fuel Pump Gauge Retainer |
| *b | SST (Plate) |
Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.
| *1 | Fuel Pump Gauge Retainer |
| *a | SST (Plate) |
| *b | SST (Claw Set) |
| *c | SST (Bolt) |
| *d | Rib |
|
Press |
While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).
| *a | Co-rotation Prevention Check Mark |
| *b | Tightening Start Position |
| *c | One and Half Rotation Position |
While one person presses the fuel suction with pump and gauge tube assembly into the fuel tank assembly, have another person firmly press the fuel pump gauge retainer into the threads of the fuel tank assembly and tighten approximately one and a half turns.
Do not use any tools other than SST, such as a screwdriver, etc.
Do not use excessive force when pressing down on SST, as the fuel suction with pump and gauge tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.
Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.
Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.
Check the tightening condition of the fuel pump gauge retainer.
| *1 | Fuel Pump Gauge Retainer |
| *2 | Fuel Tank Assembly |
| *a | Vernier Caliper |
| *b | Measurement Position |
| *c | Measurement Height |
Using a vernier caliper, measure the upper surface dimensions of the fuel tank assembly at the 3 positions as shown in the illustration.
Measurement difference is within 3 mm.
If the measurement difference is approximately 6 mm, the threads misaligned by 1 threads (6 mm) and the fuel pump gauge retainer must be installed again.
| *a | SST (Plate) |
| *b | Person in Charge of Tightening |
| *c | Person in Charge of Supporting |
While one person presses the fuel tank vent tube assembly into the fuel tank assembly, have another person slowly tighten approximately half turns.
Install SST (handle) to SST (plate).
| *a | SST (Handle) |
| *b | SST (Plate) |
| *c | Tightening Complete Position |
| *d | Rotational Start Point Mark of Fuel Pump Gauge Retainer |
| *e | Rotational Start Point Mark of Fuel Tank Assembly |
| *f | Person in Charge of Tightening |
| *g | Person in Charge of Supporting |
|
Tighten |
While one person presses the fuel suction with pump and gauge tube assembly onto the fuel tank sub-assembly, have another person use SST (handle) and slowly tighten the fuel pump gauge retainer until it reaches the tightening complete position.
Install the fuel tank main tube sub-assembly and fuel tank return tube with the 2 tube joint clips.
| *1 | Fuel Tube Joint |
| *2 | O-Ring |
| *3 | Fuel Tube |
| *4 | Fuel Tube Joint Clip |
| *a | CORRECT |
| *b | INCORRECT |
Check that there are no scratches or foreign objects on the connecting parts.
Check that the fuel tube joints are inserted securely.
Check that the tube joint clips are on the collars of the fuel tube joints.
After installing the tube joint clips, check that the fuel tube joints have not been pulled off.
77213B
3.INSTALL FUEL TANK TO FILLER PIPE HOSE
Install the fuel tank to filler pipe hose to the fuel tank assembly.
77697A
4.INSTALL NO. 2 FUEL TANK HEAT INSULATOR (for 144 L (38 US gal) Fuel Tank)
Install the No. 2 fuel tank heat insulator with the 3 clips.
77697
5.INSTALL NO. 1 FUEL TANK HEAT INSULATOR
for 100 L (26.4 US gal) Fuel Tank:
Install the No. 1 fuel tank heat insulator with the 4 clips and nut.
for 144 L (38 US gal) Fuel Tank:
Install the No. 1 fuel tank heat insulator with the 2 clips and 2 nuts.
77201
6.INSTALL INLET FUEL TANK PIPE SUB-ASSEMBLY
Install the inlet fuel tank pipe sub-assembly with the 2 nuts.
77100
7.INSTALL FUEL TANK ASSEMBLY
Set the fuel tank assembly on an engine lifter and raise the fuel tank assembly.
Connect the harness clamp and fuel pump connector to the fuel tank assembly.
Be careful not to cut the wiring.
w/ Cover:
Attach the 3 claws to install the No. 2 fuel tank protector.
Raise the engine lifter.
for 100 L (26.4 US gal) Fuel Tank:
Install the No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly with the 2 pins and 2 clips.
Connect the No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly with the 2 bolts.
for 144 L (38 US gal) Fuel Tank:
Install the 2 No. 1 fuel tank band sub-assemblies and No. 2 fuel tank band sub-assembly with the 3 pins and 3 clips.
Connect the 2 No. 1 fuel tank band sub-assemblies and No. 2 fuel tank band sub-assembly with the 3 bolts.
77754
8.CONNECT OUTLET NO. 1 CANISTER HOSE
Connect the outlet No. 1 canister hose to the inlet fuel tank pipe sub-assembly.
| *1 | Pipe |
| *2 | Retainer |
| *3 | Connector |
| *4 | O-Ring |
| *5 | Nylon Tube |
| *a | Push |
Attach the hose to the No. 1 breather tube clamp.
77213B
9.CONNECT FUEL TANK TO FILLER PIPE HOSE
Connect the fuel tank to filler pipe hose to the inlet fuel tank pipe sub-assembly.
Connect the fuel tank breather tube to the inlet fuel tank pipe sub-assembly.
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
Attach the lock claws to the connector by pushing down on the cover as shown in the illustration.
Attach the filler pipe hose and fuel tank breather tube to the No. 1 breather tube clamp.
10.CONNECT WIRE HARNESS
Attach the harness clamp to the fuel tank assembly.
11.CONNECT VENT LINE HOSE
Connect the vent line hose and install the retainer.
Before installing the hose, make sure that it is not damaged. Make sure that there is no foreign matter present on the connecting surfaces.
After connecting, check if the hose and the connector are securely connected by pulling on them.
77204A
12.CONNECT FUEL TANK RETURN TUBE
for 100 L (26.4 US gal) Fuel Tank:
Connect the fuel tank return tube.
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
| *1 | Pipe |
| *2 | Retainer |
| *3 | Connector |
| *4 | O-Ring |
| *5 | Nylon Tube |
| *a | Push |
Attach the lock claws to the connector by pushing down on the cover as shown in the illustration.
for 144 L (38 US gal) Fuel Tank:
Connect the fuel tank return tube.
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
| *1 | Retainer |
| *a | Push |
Push down the retainer.
77209D
13.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
for 100 L (26.4 US gal) Fuel Tank:
Connect the fuel tank main tube.
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
| *1 | Pipe |
| *2 | Retainer |
| *3 | Connector |
| *4 | O-Ring |
| *5 | Nylon Tube |
| *a | Push |
Attach the lock claws to the connector by pushing down on the cover as shown in the illustration.
for 144 L (38 US gal) Fuel Tank:
Connect the fuel tank main tube.
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
| *1 | Retainer |
| *a | Push |
Push down the retainer.
77606
14.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)
for 100 L (26.4 US gal) Fuel Tank:
Install the No. 1 fuel tank protector sub-assembly with the 2 bolts and 2 nuts.
for 144 L (38 US gal) Fuel Tank:
Install the No. 1 fuel tank protector sub-assembly with the 6 nuts.
77310A
15.INSTALL FUEL TANK CAP
28800
16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
17.INSPECT FOR FUEL LEAK