Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Manual Seat) › from 2016.08
RM27M0U _58 Vehicle Interior _049136 SEAT _0234294 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SEAT CUSHION SHIELD WIRE LH

a.

Install the front seat cushion shield wire LH with the 2 screws.


Hide 2.INSTALL FRONT SEAT CUSHION SHIELD WIRE RH (for Front Passenger Side)

HINT:

Use the same procedure described for the LH side.


Hide 72125N 3.INSTALL UPPER NO. 4 SEAT TRACK COVER

a.

Attach the 2 claws to install the upper No. 4 seat track cover.


Hide 72125M 4.INSTALL UPPER NO. 3 SEAT TRACK COVER

HINT:

Use the same procedure described for the upper No. 4 seat track cover.


Hide 72125A 5.INSTALL UPPER SEAT TRACK COVER

a.

Attach the 2 claws to install the upper seat track cover.

HINT:

Use the same procedure for all upper seat track covers.



Hide 71874 6.INSTALL FRONT LOWER SEAT CUSHION SHIELD LH

a.

Attach the 2 claws to install the front lower seat cushion shield LH.


Hide 71873 7.INSTALL FRONT LOWER SEAT CUSHION SHIELD RH

HINT:

Use the same procedure described for the LH side.


Hide 71620S 8.INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

a.

Attach the 4 hooks of the rear side to install the separate type front seat cushion spring assembly.


b.

Attach the hook of the front side.


Hide 82191 9.INSTALL FRONT SEAT CUSHION WIRE RH (for Front Passenger Side)

a.
U152050E01
1.006,0.305 1.187,0.480 0.181,0.174 10 *1 0.322,1.354 0.504,1.528 0.181,0.174 10 *2 3.085,1.066 3.267,1.240 0.181,0.174 10 *2 1.742,1.351 1.923,1.525 0.181,0.174 10 *2 1.206,0.433 1.412,0.515 false 0.523,1.395 0.841,1.206 false 1.369,0.802 1.822,1.181 1.822,1.181 2.276,0.807 false 1.82,0.828 1.82,1.288 false 2.766,1.159 3.084,1.159 false

Attach the connector clamp and 5 wire harness clamps to install the front seat cushion wire RH.

Text in Illustration
*1 Connector Clamp
*2 Wire Harness Clamp


b.

Connect the 4 connectors.


Hide 89952 10.INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)

Hide 71072S 11.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.

Set the separate type front seat cushion cover in place.


b.
B354573E02
1.104,0.448 0.75,0.677 true 2.458,0.479 2.813,0.708 true 0.854,2.188 0.354,2.427 true 0.875,2.958 0.573,2.958 false 0.573,0.635 0.792,0.823 0.219,0.188 10 false *1 0.146,2.375 0.365,2.563 0.219,0.188 10 false *a 0.406,2.885 0.625,3.073 0.219,0.188 10 false *2 2.833,0.656 3.052,0.844 0.219,0.188 10 false *1

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 10 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



HINT:

Install the hog rings at the cutouts if they are there.



c.

Attach the 2 fasteners.

Text in Illustration
*1 Fastener
*2 Hog Ring Pliers
*a Cutout


Hide 12.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

Attach the 12 hooks to install the separate type front seat cushion cover with pad.

B354571


Hide 71759B 13.INSTALL FRONT SEATBACK HOOK

a.

Install the 2 front seatback hooks to the front seatback spring assembly.


Hide 71013 14.INSTALL FRONT SEATBACK SPRING ASSEMBLY

a.

Attach the 2 guides and 2 clips to install the front seatback spring assembly.


Hide 72574 15.INSTALL RECLINING CONTROL LEVER LH

a.

Install the reclining control lever LH with the bolt.


Hide 71552S 17.INSTALL SEPARATE TYPE FRONT SEATBACK PAD

a.

Install the separate type front seatback pad to the front seatback frame sub-assembly LH.


Hide 71074S 18.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

Set the separate type front seatback cover in place.


b.

Attach the 4 claws to install the 2 front seat headrest supports.


c.
B354566E02
0.729,2.375 1.344,2.188 true 1.406,2.906 1.031,2.906 false 0.833,2.813 1.021,3 0.188,0.188 10 false *1 0.552,2.313 0.74,2.5 0.188,0.188 10 false *a

Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


d.
B354568E01
0.348,0.447 0.513,0.608 0.165,0.161 10 *1 0.549,0.536 1.242,0.536 false 0.348,1.043 0.513,1.204 0.165,0.161 10 *1 0.549,1.132 1.293,1.132 false 0.348,0.115 0.513,0.275 0.165,0.161 10 *1 2.863,0.447 3.028,0.608 0.165,0.161 10 *1 2.863,1.043 3.028,1.204 0.165,0.161 10 *1 2.863,0.115 3.028,0.275 0.165,0.161 10 *1 0.549,0.204 1.379,0.204 false 2.84,0.536 2.147,0.536 false 2.84,1.132 2.096,1.132 false 2.84,0.204 2.01,0.204 false

Attach the 6 fasteners.

Text in Illustration
*1 Fastener


e.

Pass the 4 straps of the separate type front seatback cover through the separate type front seatback pad.


f.

Attach the 2 hooks.

CAUTION:
·

For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

·

Make sure that the strap is not twisted after attaching the 2 hooks.

·

Attach the 2 hooks securely.



i.

Slide each hook to attach them.


ii.

Install the 4 clips.



g.
B356803

Close the 2 fasteners.


h.

Pass the wire harness through the separate type front seatback cover.


i.

Attach the hook.


Hide 19.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.

When reusing a bolt:

i.

Clean the threads of the bolt with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




b.
B354560

Install the separate type front seatback assembly with the 4 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


c.
B354559E01
3.12,0.787 3.318,0.966 0.198,0.179 10 *2 3.081,0.158 3.279,0.337 0.198,0.179 10 *1 2.353,0.261 3.052,0.261 false 2.371,0.433 3.034,0.874 3.034,0.874 2.296,1.481 false 2.405,0.874 3.099,0.874 false

Attach the connector clamp and 3 wire harness clamps to connect the wire harness of the front seat airbag assembly LH.

Text in Illustration
*1 Connector Clamp
*2 Wire Harness Clamp


Hide 71868A 20.INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH

a.
B354557

Attach the guide in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.


b.

Install the 2 screws.


Hide 73240 22.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

Hide 73230 23.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

Hide 71812D 24.INSTALL FRONT SEAT CUSHION SHIELD LH

a.
U152048E01
0.142,1.901 0.335,2.093 0.193,0.193 10 (1) 1.964,0.783 2.157,0.976 0.193,0.193 10 (2)

Attach the 2 claws, clip and guide as indicated by the arrows in the order shown in the illustration to install the front seat cushion shield LH.


b.

Install the 3 screws.


c.

Connect the 2 rubber bands.


Hide 72526 25.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.

Attach the claw to install the reclining adjuster release handle LH.