Home › Drivetrain › K320 (MULTIDRIVE / CVT) › SHIFT PADDLE SWITCH
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438039 SHIFT PADDLE SWITCH A

K320 MULTIDRIVE / CVT  SHIFT PADDLE SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C449099N03
0.583,2.167 2.417,3.75 1.833,1.583 1.417,1.365 1.552,1 1.552,1 1.719,1 false 4.24,3.833 4.073,3.833 4.073,3.833 3.917,3.354 false 2.083,3.167 2.083,2.833 false 0.917,3.417 0.917,3.083 false 1.51,4.25 1.51,3.75 false 6.563,2.74 6.396,2.74 6.396,2.74 6.24,2.26 false 5.104,2.729 4.938,2.729 4.938,2.729 4.781,2.25 false 4.281,3.719 4.677,4.052 0.396,0.333 18 false 1 1.771,0.927 2.083,1.083 0.313,0.156 10 false *3 0.844,3.438 1.156,3.594 0.313,0.156 10 false *1 2.021,3.177 2.333,3.333 0.313,0.156 10 false *2 4.875,2.125 5.156,2.323 0.281,0.198 10 false x2 1.563,4.271 1.958,4.604 0.396,0.333 18 false 3 6.615,2.604 7.01,2.938 0.396,0.333 18 false 2 5.135,2.667 5.635,2.896 0.5,0.229 10 false ●★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING WHEEL ASSEMBLY 45100 - - -
2 STEERING PAD SWITCH ASSEMBLY 84250A - - -
3 SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) - (Click here) - -

*1 NO. 1 TRANSMISSION SHIFT SWITCH ASSEMBLY *2 NO. 2 TRANSMISSION SHIFT SWITCH ASSEMBLY
*3 NO. 1 SWITCH WIRE - -
● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during shift paddle switch (transmission shift switch assembly) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 45100 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 84250A 2.REMOVE STEERING PAD SWITCH ASSEMBLY

Hide 3.REMOVE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

a.
C449100N01
0.365,0.083 0.646,0.438 0.281,0.354 18 false i 4.094,0.198 4.375,0.552 0.281,0.354 18 false ii 0.26,1.927 0.542,2.281 0.281,0.354 18 false iii 4.073,2.01 4.354,2.365 0.281,0.354 18 false iv

i.

Remove the 2 screws and disengage the 2 guides to disconnect the 2 shift paddle switches (transmission shift switch assemblies) from the steering wheel assembly.


ii.

Disengage the 4 claws.


iii.

Disengage the 4 guides to remove the 2 shift paddle switches (transmission shift switch assemblies) with No. 1 switch wire from the steering wheel assembly.


iv.

Disconnect the No. 1 transmission shift switch assembly connector and No. 2 transmission shift switch assembly connector to remove the No. 1 transmission shift switch assembly and No. 2 transmission shift switch assembly from the No. 1 switch wire.