Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM3700E _59 Vehicle Exterior _092998 WINDOW / GLASS _0438347 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B586221N01
6.438,0.271 6.771,0.271 false 2.708,0.667 3.042,0.667 false 3.573,1.49 3.75,1.49 false 5.563,2.271 5.948,2.271 false 5.271,2.885 5.75,2.885 false 5.354,3.552 5.75,3.552 false 4.688,4.49 5.083,4.49 false 5,5.135 5.333,5.135 false 1.427,3.375 1.646,3.375 false 1.823,2.552 1.979,2.552 false 3.635,2.104 3.865,2.104 false 5.865,0.115 6.51,0.458 0.646,0.344 18 false 1, 12 3.104,0.521 3.385,0.875 0.281,0.354 18 false 9 4.063,1.385 4.344,1.74 0.281,0.354 10 false ● 4.24,1.302 4.521,1.656 0.281,0.354 18 false 6 6.229,2.208 6.51,2.563 0.281,0.354 10 false ● 6.406,2.125 6.688,2.479 0.281,0.354 18 false 5 6.021,2.75 6.302,3.104 0.281,0.354 18 false 8 6.01,3.521 6.292,3.875 0.281,0.354 10 false ● 6.188,3.417 6.469,3.771 0.281,0.354 18 false 7 4.375,4.323 4.708,4.656 0.333,0.333 18 false 11 5.385,4.99 5.719,5.323 0.333,0.333 18 false 10 1.01,3.302 1.292,3.656 0.281,0.354 10 false ● 1.198,3.219 1.531,3.552 0.333,0.333 18 false 4 1.5,2.49 1.781,2.844 0.281,0.354 10 false ● 1.667,2.406 2,2.74 0.333,0.333 18 false 2 3.281,2.042 3.448,2.365 0.167,0.323 10 false ● 3.438,1.948 3.771,2.281 0.333,0.333 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CLEAN BACK DOOR GLASS - (Click here) - -
2 BACK WINDOW GLASS CLIP LH 64828B (Click here) - -
3 BACK WINDOW GLASS CLIP RH 64827B (Click here) - -
4 BACK WINDOW OUTSIDE MOULDING LH 75574B (Click here) - -
5 BACK WINDOW OUTSIDE MOULDING RH 75573C (Click here) - -
6 BACK WINDOW GLASS ADHESIVE DAM 64813B (Click here) - -
7 BACK WINDOW LOWER MOULDING 75575D (Click here) - -
8 INSTALL BACK DOOR GLASS 68131 (Click here) - -
9 REAR SPOILER SIDE PROTECTOR SUB-ASSEMBLY RH 76807 - - -
10 REAR WIPER MOTOR GROMMET 85143R - - -
11 BACK DOOR OUTSIDE GARNISH - - - -
12 INSPECT FOR LEAK - (Click here) - -

● Non-reusable part - -

PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS

a.
B590207C02
1.469,0.219 1.75,0.521 0.281,0.302 18 false i 4.594,0.24 4.875,0.542 0.281,0.302 18 false ii 0.948,0.281 1.323,0.521 0.375,0.24 12 false *A
*A When reusing the Back Door Glass - -


i.

When reusing the back door glass:

1. Using a scraper, remove any remaining adhesive residue from the back door glass.

NOTICE:

Be careful not to damage the back door glass.



ii.

Clean the outer circumference of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the back door glass surface after cleaning it.

·

Even if using a new back door glass, clean it with a non-residue solvent.





Hide 64828B 2.INSTALL BACK WINDOW GLASS CLIP LH

a.

When reusing the back door glass:

B586222C01
5.302,0.854 5.688,0.573 true 1.021,0.24 1.333,0.438 0.313,0.198 10 false *a 3.292,0.083 3.583,0.448 0.292,0.365 18 false i 4.781,0.479 5.146,0.833 0.365,0.354 18 false ii 5.75,0.49 6.063,0.688 0.313,0.198 10 false *b
*a Back Side of Back Door Glass *b Ag Print Mark


i.

Using a brush or sponge, coat the installation area of the back window glass clip LH with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



ii.

Install the a new back window clip LH to the back door glass as shown in the illustration.



Hide 64827B 3.INSTALL BACK WINDOW GLASS CLIP RH

Hide 75574B 4.INSTALL BACK WINDOW OUTSIDE MOULDING LH

a.

When reusing the back door glass:

B586223C01
5.76,0.635 5.927,0.458 true 6.125,2.365 5.938,2.188 true 0.688,0.563 1,0.719 0.313,0.156 10 false *a 6.177,2.333 6.49,2.49 0.313,0.156 10 false *b 5.958,0.365 6.271,0.521 0.313,0.156 10 false *b 3.698,0.417 4.146,0.833 0.448,0.417 18 false i 5.208,0.229 5.385,0.5 0.177,0.271 18 true ii 5.219,1.573 5.396,1.844 0.177,0.271 18 true ii
*a Back Side of Back Door Glass *b R end


i.

Using a brush or sponge, coat the installation area of the back window outside moulding LH with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



ii.

Install the a new back window outside moulding LH to the back door glass as shown in the illustration.



Hide 75573C 5.INSTALL BACK WINDOW OUTSIDE MOULDING RH

Hide 64813B 6.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

When reusing the back door glass:

B586224C01
0.969,0.823 0.813,1.021 true 6.292,1.01 6.479,0.792 true 2.51,1 2.823,1.156 0.313,0.156 10 false *a 1.021,0.677 1.208,0.823 0.188,0.146 10 true *b 6.521,0.708 6.708,0.854 0.188,0.146 10 true *b 3.365,1.031 3.667,1.365 0.302,0.333 18 false i 5.635,0.583 5.958,1.021 0.323,0.438 18 false ii 0.469,0.604 0.792,1.042 0.323,0.438 18 false ii
*a Back Side of Back Door Glass *b R end


i.

Using a brush or sponge, coat the installation area of the back window glass adhesive dam with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



ii.

Install the a new back window glass adhesive dam to the back door glass as shown in the illustration.



Hide 75575D 7.INSTALL BACK WINDOW LOWER MOULDING

a.

When reusing the back door glass:

B586225C01
1.323,1.865 1.125,1.677 true 6.031,1.719 5.844,1.865 true 2.031,0.104 2.344,0.26 0.313,0.156 10 false *a 0.896,1.583 1.094,1.74 0.198,0.156 10 true *b 6.063,1.625 6.26,1.781 0.198,0.156 10 true *b 1.052,1.302 1.292,1.635 0.24,0.333 18 false ii 3.198,1.719 3.344,2 0.146,0.281 18 true i 5.396,1.313 5.563,1.573 0.167,0.26 18 true ii
*a Back Side of Back Door Glass *b R end


i.

Using a brush or sponge, coat the installation area of the back window lower moulding with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



ii.

Install the a new back window lower moulding to the back door glass as shown in the illustration.



Hide 68131 8.INSTALL BACK DOOR GLASS

a.
B590229C01
0.49,0.146 1.865,0.5 1.375,0.354 18 false i
V100155

Adhesive - -


i.

Clean and shape the contact surface of the vehicle body.

1. Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.


2 Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.



b.
B586226C01
3.917,1.51 3.583,1.552 3.583,1.552 3.781,1.25 true 2.552,1.5 3.271,1.094 true 4.094,0.906 5.052,1.073 true 3.333,1.51 3.563,1.698 0.229,0.188 10 true *a 2.323,1.427 2.552,1.615 0.229,0.188 10 true *b 5.094,0.99 5.323,1.177 0.229,0.188 10 false *b 0.427,0.083 0.708,0.438 0.281,0.354 18 false i
*a Matchmark *b Suction Cup


i.

Prepare to install the back door glass by the below procedure.

1. Using suction cups, place the back door glass in the correct position.

2. Check that the whole contact surface of the back door glass rim is perfectly even.

3. Align the matchmarks on the back door glass and vehicle body.

NOTICE:

Check that the back window glass clips are engaged to the vehicle body correctly.


4. Remove the back door glass.

5. Using a brush, coat the installation surface on the vehicle body with body primer.

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.




c.
B586227C01
6.135,0.844 6.427,0.677 false 0.479,0.104 0.76,0.458 0.281,0.354 18 false i 0.406,1.427 0.656,1.635 0.25,0.208 10 false *a 1.823,1.833 2.073,2.042 0.25,0.208 10 false A 1.792,2.177 1.927,2.365 0.135,0.188 10 true A 1.802,3.281 1.938,3.469 0.135,0.188 10 true B 1.823,3.667 2.073,3.875 0.25,0.208 10 false B 0.802,1.927 0.938,2.115 0.135,0.188 10 true C 3.198,1.729 3.448,1.938 0.25,0.208 10 false D 4.896,0.323 5.219,0.49 0.323,0.167 10 false A-A 5.729,0.396 6.052,0.563 0.323,0.167 10 false a 6.479,0.552 6.802,0.719 0.323,0.167 10 false *1 4.927,1.448 5.25,1.615 0.323,0.167 10 false B-B 5.781,1.448 6.104,1.615 0.323,0.167 10 false b 4.479,2.927 4.802,3.094 0.323,0.167 10 false C-C 6.052,3.01 6.375,3.177 0.323,0.167 10 false c 0.448,1.823 0.583,2.01 0.135,0.188 10 true C 3.281,2.083 3.406,2.271 0.125,0.188 10 true D 5.104,3.802 5.427,3.969 0.323,0.167 10 false d 5.833,4.833 6.156,5 0.323,0.167 10 false e 6.146,4.49 6.469,4.656 0.323,0.167 10 false f 4.635,4.49 4.958,4.656 0.323,0.167 10 false D-D
*1 Back Window Glass Adhesive Dam - -
*a Back Side of Back Door Glass - -
V100155

Glass Primer - -


i.

Using a brush or sponge, coat the adhesive application area with glass primer as shown in the illustration.

Standard Dimension:
Area Dimension
a 14.8 mm (0.583 in.) or more
b 11 mm (0.433 in.) or more
c 22 mm (0.866 in.) or more
d 83.6 mm (3.291 in.)
e 14.8 mm (0.583 in.)
f 6.3 mm (0.248 in.)


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:
·

Apply glass primer onto the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.





d.
B582006C02
3.188,0.271 3.063,0.344 false 4.427,0.406 4.854,0.156 true 3.24,0.177 3.552,0.333 0.313,0.156 10 false *b 0.479,0.104 0.781,0.406 0.302,0.302 18 false i 2.417,0.479 2.729,0.635 0.313,0.156 10 false a 2.615,0.906 2.927,1.063 0.313,0.156 10 false b 2.969,0.729 3.281,0.885 0.313,0.156 10 false b 3.167,1.323 3.479,1.479 0.313,0.156 10 false a 4.896,0.083 5.208,0.281 0.313,0.198 10 false *a
*a Sealer Gun *b Cartridge Nozzle
V100155

Adhesive - -


i.

Prepare to apply adhesive to the back door glass by the below procedure.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


1. Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12 to 15 mm (0.472 to 0.591 in.)
b 8.0 to 11 mm (0.315 to 0.433 in.)


2. Load the sealer gun with the cartridge.



e.
B586228C01
6.427,0.594 6.063,0.76 true 6.49,0.5 6.802,0.656 0.313,0.156 10 false *1 0.479,0.115 0.635,0.448 0.156,0.333 18 false i 0.281,1.406 0.594,1.563 0.313,0.156 10 false *a 4.823,0.177 5.135,0.333 0.313,0.156 10 false A-A 5.927,0.281 6.24,0.438 0.313,0.156 10 false a 4.885,1.531 5.198,1.688 0.313,0.156 10 false B-B 5.823,1.354 6.135,1.51 0.313,0.156 10 false b 4.375,3 4.688,3.156 0.313,0.156 10 false C-C 5.188,4 5.479,4.156 0.292,0.156 10 false d 1.833,1.833 2.146,1.99 0.313,0.156 10 false A 1.781,2.177 1.938,2.375 0.156,0.198 10 true A 1.802,3.271 1.927,3.438 0.125,0.167 10 true B 1.813,3.656 2.125,3.813 0.313,0.156 10 false B 3.25,2.063 3.406,2.26 0.156,0.198 10 true D 3.135,1.719 3.448,1.875 0.313,0.156 10 false D 5.49,1.677 5.802,1.833 0.313,0.156 10 false c 0.458,1.833 0.615,2 0.156,0.167 10 true C 0.813,1.979 0.969,2.146 0.156,0.167 10 true C 5.979,4.406 6.271,4.563 0.292,0.156 10 false e 4.521,4.344 4.833,4.5 0.313,0.156 10 false D-D
*1 Back Window Glass Adhesive Dam - -
*a Back Side of Back Door Glass - -
V100155

Adhesive - -


i.

Apply adhesive to the back door glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 14.1 mm (0.555 in.)
b 7.8 mm (0.307 in.)
c 14.6 mm (0.575 in.)
d 90.6 mm (3.567 in.)
e 13.7 mm (0.539 in.)




f.
B586229C01
3.927,1.49 3.604,1.594 3.604,1.594 3.771,1.24 true 3.292,1.115 2.656,1.49 true 5.052,1.198 4.094,0.906 true 3.375,1.521 3.594,1.698 0.219,0.177 10 true *a 0.573,0.208 0.854,0.563 0.281,0.354 18 false i 2.438,1.469 2.646,1.656 0.208,0.188 10 true *b 5.094,1.135 5.406,1.333 0.313,0.198 10 false *b
*a Matchmark *b Suction Cup


i.

Install the back door glass by the below procedure.

1. Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the back window glass spacers are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and back door glass sub-assembly.



2. Lightly press the outer surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.


3. Using a scraper, remove any excess or protruding adhesive.

4. Hold the back door glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




g.
B586212N02
1.229,0.042 1.51,0.396 0.281,0.354 18 false i

i.

Connect each connector.



h.

w/ Digital Audio Broadcasting Antenna:

B590366N01
1.875,0.052 2.156,0.406 0.281,0.354 18 false i

i.

Connect the connector.



Hide 76807 9.INSTALL REAR SPOILER SIDE PROTECTOR SUB-ASSEMBLY RH

Hide 85143R 10.INSTALL REAR WIPER MOTOR GROMMET

Hide 12.INSPECT FOR LEAK

a.
B586230N01
0.521,0.146 0.698,0.427 0.177,0.281 18 false i

i.

Inspect for leaks by the below procedure.

1. Remove the protective tape.

2. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

3. If water leaks into the cabin, allow the water to dry and add adhesive.