Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM3700E _59 Vehicle Exterior _092999 WIPER / WASHER _0438354 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B586320N02
4.438,0.688 5.521,0.854 1.083,0.167 5.646,3.135 6.729,3.302 1.083,0.167 5.365,3.49 6.448,3.656 1.083,0.167 3.385,3.448 4.469,3.615 1.083,0.167 2.958,3.135 2.958,2.885 false 4.781,2.167 5.198,2.167 false 5.021,1.208 5.177,1.208 5.177,1.208 5.281,1.469 false 4.292,3.156 4.583,3.156 false 6.188,0.615 6.479,0.615 false 6.438,0.26 6.792,0.26 false 5.521,0.771 5.688,0.771 5.688,0.771 5.854,1.021 false 5.354,3.219 5.646,3.219 false 5.021,3.396 5.188,3.563 5.188,3.563 5.365,3.563 false 4.469,3.531 4.625,3.531 4.625,3.531 4.719,3.344 false 2.896,3.146 3.177,3.5 0.281,0.354 18 false 3 4.594,2 4.875,2.354 0.281,0.354 18 false 1 4.802,1.073 5.083,1.427 0.281,0.354 18 false 4 4.104,2.979 4.385,3.333 0.281,0.354 18 false 2 6.552,0.458 6.833,0.813 0.281,0.354 18 false 6 6.26,0.104 6.458,0.396 0.198,0.292 18 false 5 4.521,0.708 5.51,0.906 0.99,0.198 8 false 5.5 (56, 49 in.*lbf) 5.76,3.156 6.917,3.323 1.156,0.167 8 false 5.5 (56, 49 in.*lbf) 5.448,3.5 6.552,3.667 1.104,0.167 8 false 5.5 (56, 49 in.*lbf) 3.469,3.458 4.646,3.656 1.177,0.198 8 false 5.5 (56, 49 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR WIPER MOTOR GROMMET 85143R (Click here) - -
2 REAR WIPER MOTOR AND BRACKET ASSEMBLY 85120R - - -
3 BACK DOOR TRIM BOARD 67751 - - -
4 INSTALL REAR WIPER ARM AND BLADE ASSEMBLY - (Click here) - -
5 INSPECT REAR WIPER ARM AND BLADE ASSEMBLY - (Click here) - -
6 REAR WIPER ARM HEAD CAP 85292A - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

MP grease

PROCEDURE

Hide 85143R 1.INSTALL REAR WIPER MOTOR GROMMET

a.
B586321C01
5.75,0.677 6.125,0.313 true 1.792,0.396 2.135,0.99 2.135,0.99 2.49,0.396 true 0.563,0.083 0.844,0.438 0.281,0.354 18 false i 3.823,0.115 4.104,0.469 0.281,0.354 18 false ii 6.177,0.219 6.49,0.417 0.313,0.198 10 false *b 2.063,1.01 2.375,1.208 0.313,0.198 10 false *a
*a Rear Wiper Motor Grommet Lip *b Alignment Mark
V100145

MP grease - -


i.

Apply MP grease to the entire surface of the rear wiper motor grommet lip.

NOTICE:

Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



ii.

Install the rear wiper motor grommet with its alignment mark facing up.



Hide 85120R 2.INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

Hide 67751 3.INSTALL BACK DOOR TRIM BOARD

Hide 4.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.
B586322C02
1.063,1.052 1.802,0.885 true 1.958,2.292 2.531,2.74 true 5.375,2.458 5.625,2.177 true 0.531,0.135 1.042,0.5 0.51,0.365 18 false i, ii 3.938,0.135 4.594,0.542 0.656,0.406 18 false iii 1.781,3.854 2.063,4.208 0.281,0.354 18 false v 0.885,0.99 1.115,1.229 0.229,0.24 10 false *a 2.583,2.677 2.813,2.917 0.229,0.24 10 false *a 5.677,2.073 5.906,2.25 0.229,0.177 10 true *b 5.094,2.25 5.229,2.406 0.135,0.156 10 true A 5.073,2.49 5.208,2.656 0.135,0.167 10 true A 4.208,1.969 4.583,2.417 0.375,0.448 18 false iv
*a Serration *b Alignment Mark


i.

When reusing the rear wiper arm and blade assembly:

1. Clean the rear wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.



ii.

When reusing the rear wiper motor assembly:

1. Clean the wiper pivot serrations with a wire brush.

NOTICE:

Do not grind down the wiper arm serrations.



iii.

Set the automatic stop position by the below procedure.

1. Turn the ignition switch on.

2. Operate the rear wiper motor assembly and stop it at the automatic stop position.

3. Turn the ignition switch off.


iv.

Install the rear wiper arm and blade assembly to the position shown in the illustration.

Reference Measurement:
Area Measurement
A 10 mm (0.394 in.)



v.

Hold the wiper arm by hand to install the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)



Hide 5.INSPECT REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85292A 6.INSTALL REAR WIPER ARM HEAD CAP