The combination meter assembly blinks or turns off the passenger seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (for passenger side) and occupant detection sensor (front seat cushion pad (for passenger side)).
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION
If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Passenger Seat Buckle Switch Status | Passenger side seat belt buckle switch status | Set, Unset, Unknown | Set: Passenger seat belt fastened
Unset: Passenger seat belt not fastened Unknown: Data is not determined |
- |
| Passenger Seat Occupant Sensor Status | Passenger seat occupant detection sensor status | OFF, ON, Unknown | OFF: Passenger seat not occupied
ON: Passenger seat occupied Unknown: Data is not determined |
- |
| Tester Display |
|---|
| Passenger Seat Buckle Switch Status |
| Passenger Seat Occupant Sensor Status |
The GTS display changes correctly in response to the front passenger seat belt and front passenger seat condition.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Passenger Seat Buckle Switch Status) | B |
| NG (Passenger Seat Occupant Sensor Status) | C |
A
B
C
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt Warning | Front seat belt warning light | ON or OFF | - |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O18)Location & Routingewd_type=routing;type=c;code=O18 Click Connector(O18)Seat>Floor Wire>Front Seat Inner Belt Assembly LHewd_type=component;type=c;code=O18;pinno=3,2 |
||
| O18-3 (+) - 4E-11 | Always | Below 1 Ω |
| O18-3 (+) or 4E-11 - Body ground | Always | 10 kΩ or higher |
| O18-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR (for Front Passenger Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O18)Location & Routingewd_type=routing;type=c;code=O18 Click Connector(O18)Seat>Floor Wire>Front Seat Inner Belt Assembly LHewd_type=component;type=c;code=O18;pinno=5,4 |
||
| O18-5 (+) - 4E-29 | Always | Below 1 Ω |
| O18-5 (+) or 4E-29 - Body ground | Always | 10 kΩ or higher |
| O18-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG