| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | AIR DUCT ASSEMBLY | 87220 | - | - | - |
| 2 | FRONT PANEL SILENCER | 55211B | ( )
|
- | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 3 | NO. 1 COOLER THERMISTOR | 88625 | - | - | - |
| 4 | NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY | 88501 | - | - | - |
| 5 | HEATER RADIATOR UNIT SUB-ASSEMBLY | 87107A | - | - | - |
| 6 | HEATER CLAMP | 87124B | - | - | - |
| *1 | UPPER HEATER CASE | - | - |
| *A | for Automatic Air Conditioning System | *B | for Manual Air Conditioning System |
| *A | for Automatic Air Conditioning System | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
for Gasoline Model:
Compressor oil ND-OIL 8 or equivalent for HV Model: Compressor oil ND-OIL 11 or equivalent |
- | - |
87220
1.INSTALL AIR DUCT ASSEMBLY
55211B
2.INSTALL FRONT PANEL SILENCER
Install the front panel silencer with the 3 retainers as shown in the illustration.
88625
3.INSTALL NO. 1 COOLER THERMISTOR
88501
4.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
87107A
5.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
87124B
6.INSTALL HEATER CLAMP
87114B
7.INSTALL HEATER COVER
55909A
8.INSTALL AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)
| *a | MAX-COLD | *b | MAX-HOT |
Set the cable gear and unit gear to the MAX COLD position.
Engage the guides and claws to install the air mix damper control cable sub-assembly.
Engage the clamps.
55906A
9.INSTALL DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)
| *a | FACE | *b | 45° |
Set the cable gear and unit link to the FACE position.
Engage the claws to install the defroster damper control cable sub-assembly.
Engage the clamp.
87050C
10.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)
| *a | Align shapes | - | - |
Move the gear of the air conditioner radiator assembly so that the shape of the center gear portion of the air conditioner radiator assembly is aligned with the sensor shaft and output shaft of the No. 1 air conditioning radiator damper servo sub-assembly, and temporarily install the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
Install the No. 1 air conditioning radiator damper servo sub-assembly with the 3 screws.
87130D
11.INSTALL BLOWER ASSEMBLY
88650N
12.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
82210K
13.INSTALL AIR CONDITIONING HARNESS ASSEMBLY (for Automatic Air Conditioning System)
88539J
14.INSTALL DRAIN COOLER HOSE
| *a | Lower Heater Case | *b | Rib |
| *c | Hose Notch | - | - |
Align the hose notch with the rib as shown in the illustration and install the drain cooler hose.
Do not place the rib on top of the drain cooler hose. Otherwise, water may leak into the interior.
88482A
15.INSTALL COVER
87211A
16.INSTALL NO. 2 AIR DUCT
|
|
88897P
17.INSTALL ASPIRATOR
88515
18.INSTALL COOLER EXPANSION VALVE
Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.
for Gasoline Model:
ND-OIL 8 or equivalent
for HV Model:
ND-OIL 11 or equivalent
Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.
88897K
19.INSTALL COOLER PIPE GROMMET
55990B
20.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY